Waterhouse XC-SP1606 Manuel utilisateur

12 Volt Hot Water Circulation Pump User Guide Manual

Model: XC-SP1606

Caution:

Please read all instructions carefully before installing this product.

This pump is not ip68 sealed and therefore shall by any means never be submerged.

However, the electric wire connections must not be submerged. For extra protection please

insulate all joins and ends with approved insulation or shrink tapes to avoid electric shocks

and fire sparks that may cause explosions or fires.

Security:

•12V brushless pumps can only be used for pumping clean cold and hot water and

non-corrosive chemicals and liquids.

•Please connect pump’s black and white wire to the negative terminal (-) and white

wire to the positive terminal (+).

•Make sure you use suitable size fuses.

•The wire connections must be insulated by shrink or watertight insulation tape.

•All wire connections must be outside water, unless necessary provided you have an

ip68 waterproof connector.

•Please do not run the pump dry.

•Your pump must always be protected from water splashes or any liquid chemicals.

•Make sure the pump works in a ventilated environment.

About product:

•Circulation pump is non-self-priming pump. Max Flow Rate: 20L/MIN, Max Discharge

Head: 6M

•10mm male adapter on the pump.

•Power source: DC 12V (NOT INCLUDED), Rated current: 2.0A, Brushless Motor, Low noise:

30db at 1 metre, Service life: 30000 hours.

•Max circulating water temperature: 100°C

•Do no submerge.

Specifications:

Model

Flow Rate

Volt

Current (A)

Head (m)

Cable

Outlet Dia

Weight

XC-

SP1606

20L/MIN

3.3AMP

6.0

20cm

10mm

0.30kgs

Warning:

•To prevent injury, always disconnect the power source when installing or servicing

any electric product.

•Do not use the pump-to-pump gasoline oil or any flammable liquids.

•Always make sure you use fuse amperage rated for your pump model.

•Failure to follow these instructions may result in serious injury or fire hazards.

Optional Materials:

•Mounting screws

•Mounting brackets.

Pump Mounting Instructions:

Warning: remove any polystyrene or foam blocks covering the pump around for

shipping purposes.

•Step 1: make sure you mount the pump wit5h safety brackets, make sure it is

holding firmly as to avoid too much vibration that will affect your seals and bearings.

•Step 2: now insert your hose inlet/outlet and use hose clamps to secure the pipes.

•Step 3: now you can link your inlet pipe to the water source and outlet to the supply,

you must always watch for the inlet/outlet arrow when installing this type of pump.

•Step 4: make sure your pump is at bottom of the water level as is the pump is not

self-priming.

•Step 5: make sure you pump is covered or protected from water or rains never

submerge the pump.

Pump mounting:

Operation:

1. Connect your -+ terminals accordingly to your battery positive and negative poles.

2. Make sure you have right size fuse on your positive pole.

3. Connect your pump to the control switch, depending on what operation you are

using the pump for:

•Use manual or thermostat switches for pump control.

Care & Maintenance:

•Always watch your power supply voltage or current for over voltage, under voltage

or short circuit.

•Make sure your pump filter sieve is always clean of debris or any clogging dirty.

•Careful attention will guarantee outstanding pump performance.

Parts:

For more information, please feel free to contact us on 011 466 8520 or email

us at [email protected]a

Table des matières

Autres manuels Waterhouse Pompe à eau

Waterhouse

Waterhouse XC-SP2502 Manuel utilisateur

Waterhouse

Waterhouse WH150 Manuel utilisateur

Waterhouse

Waterhouse FL-800 Manuel utilisateur

Waterhouse

Waterhouse XC-SP08301 Manuel utilisateur

Waterhouse

Waterhouse XC-SP002 Manuel utilisateur

Waterhouse

Waterhouse XC-SP006-FL35 Manuel utilisateur

Waterhouse

Waterhouse XC-SP003-FL40 Manuel utilisateur

Waterhouse

Waterhouse XC-SP0703 Manuel utilisateur

Waterhouse

Waterhouse XC-SP005 Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur