Water HP02 Manuel utilisateur

Installation Guide

HP02 SYSTEMS

Thank You for Your Purchase!

Questions ? Please contact Water, Inc. Service Department 1-800-322-9283

We will be glad to assist you!

Water, Inc 704 Kingshill Place Carson, CA 90746

TABLE OF CONTENTS

•WHAT COMES WITH THE SYSTEM

•JOB SPECIFICATION SHEET

•INSTALLATION

•START-UP INSTRUCTIONS/FLUSHING & CONDITIONING

•START-UP INSTRUCTIONS

•CONTROL FEATURES

•CONTROL OPERATION

•USER PROGRAMMING

•POWER SUPPLY LOCATION

•TROUBLE SHOOTING CODES

WHAT IS INCLUDED WITH YOUR SYSTEM

•1” NPT Plastic Yoke

•¾” NPT Plastic Yoke

•Bypass Plastic Assembly

•90 Degree Adaptor

•5800 Pentair Head

•1054 Preloaded tank (Varies on models)

•Neoprene cover or Chrome sleeve for tank protection

JOB SPECIFICATION SHEET

Model Number: _________________________________________________

Water Hardness: _______________________________________ ppm or gpg

Capacity Per Unit: _______________________________________________

Mineral Tank Size: ______________ Diameter: ________ Height: _________ Salt Setting per Regeneration:

_____________________________________

1. System Type: ____________________________________

A. System #4: 1 Tank, 1 Meter, Immediate, or Delayed Regeneration

B. System #4: Time Clock

2. Control Program Settings:

A. Backwash: ____________________________________ Minutes

C. Rapid Rinse: ___________________________________ Minutes

E. Pause Time: ___________________________________ Minutes

F. Second Backwash: ______________________________ Minutes

3. Drain Line Flow Control: _________________________ GPM

WARNING: CALIFORNIA PROPOSITION 65 WARNING This product contains chemicals known to the State of California to

cause cancer or birth defects or other reproductive harm.

IMPORTANT PLEASE READ

• The information, specifications and illustrations in this manual are based on the latest information available at the

time of printing. The manufacturer reserves the right to make changes at any time without notice.

• This manual is intended as a guide for service of the valve only. System installation requires information from several

suppliers not known at the time of manufacture. This product should be installed by a professional plumber.

• This unit is designed to be installed on potable water systems only. This product must be installed in compliance with

all state and municipal plumbing and electrical codes. Permits may be required at the time of installation.

• It is established that when daytime water pressure exceeds 75 PSI, the maximum pressure rating of 75 PSI cannot be

exceeded. A pressure regulator (not supplied) must be installed on this system or warranty is voided.

• Do not install the unit where temperatures may drop below 32°F (0°C) or above 125°F (52°C). Freezing temperatures

will cause damage to the system which will void the manufactures warranty. Do not place the unit in direct sunlight.

Black units will absorb radiant heat increasing internal temperatures. Do not strike the valve or any of the components.

• Warranty of this product extends to manufacturing defects. Misapplication of this product may result in failure to

properly condition water, or damage to product. A prefilter should be used on installations in which free solids are

present.

• In some applications local municipalities treat water with Chloramines. High Chloramine levels may damage valve

components.

• Correct and constant voltage must be supplied to the controller to maintain proper function.

INSTALLATION:

Water Pressure A minimum of 20 psi (1.4 bar) of water pressure is required for the regeneration valve to operate

effectively.

Electrical Facilities An uninterrupted alternating current (120 VAC) supply is required. The control uses a transformer to

supply 12 VDC. Please make sure your voltage supply is compatible with your unit before installation.

Installation Cont.

Existing Plumbing Condition of existing plumbing should be free from lime and iron buildup. Piping that is built up

heavily with lime and/or iron should be replaced. If piping is clogged with iron, a separate iron filter unit should be

installed ahead of the water softener.

Location Drain You must have an air gap on the drain line to prevent back flow of drain water into the system. A 2x the

drain line pipe diameter air gap is required with a minimum 1" air gap.

Outdoor Locations

When the water conditioning system is installed outdoors, several items must be considered.

• Moisture — The system is not designed to withstand extreme humidity or water spray from below. Examples:

constant heavy mist, near corrosive environment, upwards spray from sprinkler.

CAUTION This unit is for dry location use only unless used with a Listed Class 2 power supply suitable for outdoor use.

•Direct Sunlight — The materials used will fade or discolor over time in direct sunlight. The integrity of the materials

will not degrade to cause system failures. If it is necessary to locate the system in direct sunlight, a protective outdoor

cover # WI-HP-28816 over the valve and controller is necessary.

• Insects — If installing in an environment that may expose the system to insects or other small animals, a protective

cover is required. The protective outdoor cover has been designed to keep all but the smallest insects out of the critical

areas. The cover should be installed securely in place.

Bypass Valves Always provide for the installation of a bypass valve if unit is not equipped with one.

CAUTION Water pressure is not to exceed 75 psi water temperature is not to exceed 110°F (43°C), and the unit cannot

be subjected to freezing conditions.

Warning:The system must be depressurized before removing any connections for servicing.

drain

Installation Instructions

1. During cold weather, the installer should warm the valve to room temperature before operating.

2. All plumbing should be done in accordance with local plumbing codes. The pipe size for a residential drain line

should be a minimum of 1/2" (13 mm). Backwash flow rates in excess of 7 gpm (26.5 Lpm) or drain line length

in excess of 20' (6 m) require 3/4" (19 mm) drain line. Commercial drain lines should be the same size as the

drain line flow control.

NOTE: The tank should have the distributor tube installed and have the proper amount of regenerant in place.

3. Refer to the dimensional drawing for cutting height of the distributor tube. If there is no dimensional drawing,

cut the distributor tube flush with the top of the tank.

4. Lubricate the distributor O-ring seal and tank O-ring seal. Place the main control valve on tank. Note: Only use

silicone lubricant.

5. Soldering of joints near the drain port must be done prior to connecting the Drain Line Flow Control fitting

(DLFC). Leave at least 6" (15 cm) between the DLFC and solder joints when soldering pipes that are connected

on the DLFC. Failure to do this could cause interior damage to the DLFC.

6. PTFE plumbing tape is the only sealant to be used on the drain fitting.

7. Make sure that the floor is clean beneath the salt storage tank and that the tank is level.

8. On units with a bypass, place in bypass position. Turn on the main water supply. Open a cold soft water tap

nearby and let run a few minutes or until the plumbing is free from foreign material (usually solder) that may

have resulted from the installation. Once clean, close the water tap.

9. Slowly place the bypass in service position and let water flow into the mineral tank. When water flow stops,

slowly open a cold water tap nearby and let water run until the air is purged from the unit.

12. Plug the transformer into an electrical outlet.

NOTE: All electrical connections must be connected according to local codes. Be certain the outlet is uninterrupted.

Electrical Connection

The controller operates on 12-volt DC power supply. This requires use of the supplied power adapter included with

your system. See illustration below.

NOTE: The power source should be constant. Be certain the AC adapter is not on a switched outlet. Power

interruptions longer than 8 hours may cause the controller to lose the time setting. When power is restored, the

time setting must then be re-entered.

Head unit

↓

Power Supply Cord→

TROUBLESHOOTING

Error Codes

NOTE:

Error

codes

appear

the

-Service

display.

Error Code Error Type Cause

Reset

and

Recovery

---0

Motor Stall /Cam

Sense Error

No state changes in the optical

sensor are detected for six

seconds.

Unplug the unit and plug back in. Allow the control to attempt to find

position again.

Verify the optical sensor is in place with the wires connected to the

circuit board. Verify the motor and drive train components are in good

condition and assembled properly. Check the valve and verify that the

piston travels freely. Replace/reassemble the various components as

necessary.

Plug the unit back in and observe its behavior. If the error reoccurs,

unplug the unit, put it into bypass and contact technical support.

---1

Motor Run-On Error

/Cycle

Sense

Error

An undesired optical sensor state

change occurred.

Non-critical error. Extra optical sensor pulse detected. Press any

button to clear the error. Press extra cycle button to advance motor to

clear error.

---2

Regen

Failure The system has not regenerated

for more than 99 days (or 7 days if

the Control Type has been set to

Day-of-Week).

Perform a Manual Regeneration to reset the error code.

If the system is metered, verify that it is measuring flow by running

service water and watching for the flow indicator on the display. If the

unit does not measure flow, verify that the meter cable is connected

properly and that the meter is functioning properly.

Enter Master Programming Mode and verify that the unit is configured

properly, For the valve configuration. Check that the correct system

capacity has been selected, that the day override is set properly, and

that meter is identified correctly. If the unit is configured as a Day-of-

Week system, verify that at least one day is set ON. Correct the setting

as necessary.

---3

Memory

Error

Control board memory failure.

Perform a Master Reset and reconfigure the system via Master

Programming Mode. After reconfiguring the system, step the valve

through a manual regeneration. If error continues, call technical

support.

---4

Fail

Safe

Error

Valve has failed to find position in

one minute.

Unplug the unit and plug it back in. If error continues, call technical

support.

Thank You for Your Purchase!

Questions ? Please contact Water, Inc. Service Department 1-800-322-9283

F:HousePure/ HP02 5800 Installation 11-02-2022

Table des matières

Autres manuels Water Système de filtration d'eau

Water

Water Body Glove BG-12000 Manuel utilisateur

Manuels Système de filtration d'eau populaires d'autres marques

Wisy

Wisy LineAir 100 Manuel utilisateur

Schaffner

Schaffner Ecosine FN3446 Series Manuel d'utilisation

Pentair

Pentair FLECK 4600 SXT Guide de l'utilisateur

H2O International

H2O International H20-500 Manuel utilisateur

Renkforce

Renkforce 2306241 Manuel utilisateur

Neo-Pure

Neo-Pure TL3-A502 Manuel utilisateur

FLTR

FLTR OBF Manuel utilisateur

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manuel utilisateur

Applied Membranes

Applied Membranes W-G844EM Manuel utilisateur

BEGA

BEGA 116 Manuel utilisateur

WATA

WATA Standard Manuel utilisateur

Price

Price FFU series Manuel

Gaggenau

Gaggenau BRITA INTENZA 467873 Manuel utilisateur

Brita

Brita SAFF-100 Manuel utilisateur

HEISSNER

HEISSNER FPU24000-00 Manuel utilisateur

BGS technic

BGS technic 1518 Manuel utilisateur

Reverse Osmosis

Reverse Osmosis RF Series Manuel utilisateur

ubbink

ubbink Filtramax Series Manuel utilisateur