WARRIOR Trojan 40PUS12 Guide de référence rapide
PORTABLE
ELECTRICAL WINCH
Warrior Trojan Portable Utility Winch
Assembly & Operating Instructions
CONTENTS
INTRODUCTION...................................................................................... 1
GETTING TO KNOW YOUR WINCH .......................................................2
SAFETY PRECAUTIONS.........................................................................3
WINCH ASSEMBLY AND MOUNTING....................................................4
WIRING DRAWING ..................................................................................6
WINCH WORKING DEMONSTRATION...................................................7
REPLACING THE WIRE ROPE ...............................................................8
MAINTENANCE........................................................................................9
TROUBLE SHOOTING.............................................................................9
WINCH ASSEMBLY DRAWING............................................................1 0
WINCH PARTS LIST..............................................................................1 1
SPECIFICATION....................................................................................1 2
1
INTRODUCTION
Congratulations on your purchase of a high quality winch. We design and build
winches to strict specifications and with proper use and maintenance should bring you
years of satisfying service.
WARNING - Read, study and follow all instructions before operating this
device. Failure to read these instructions may result in personal injury
and/or damage to equipment.
Your winch can develop tremendous pulling forces and if used unsafely or
incorrectly could result in damage to property, serious injury or death. Throughout
this manual you will find the following symbols for caution, warning and danger.
Pay attention to these notes proceeded by these symbols as they are written for
your safety. Ultimately, safe operation of this device rests with you, the
operator/user.
This indicates a potentially hazardous situation, which if not avoided, may
result in minor or moderate injury. This notice is also used to alert you against
unsafe practices.
This indicates a potentially hazardous situation, which if not avoided, could
result in death or serious injury.
Read the owners Always use a Keep clear of Never use winch Never use
Manual. Hand Saver. Winch Wire Rope to lift or move winch to hold
And Hook while people. Load in place.
Operating.
CAUTION
WARNING
2
GETTING TO KNOW YOUR WINCH
A Portable winch is a complete winching solution in a convenient kit that
features a 4000lb rated line pull winch on a unique powder coated winch
platform, all in a compact, easy to carry composite plastic box. The kit is
easy to store, use, and repack. Complete portable utility winch requires no
installation and does not require a winch mount; however, it can be
permanently mounted on a trailer or other vehicles is need be.
Your winch is a powerful piece of machinery. It is important that you
understand the basics of its operation and specifications so that when you
need to use it, you can use it with confidence and safety.
WARNING –Do not substitute any strength grade weaker than ISO grade 8.8
WARNING –Be sure that both the mounting plate and winch hardware have been
securely tightened.
CAUTION –No part of the vehicle (skid pates, wiring, auxiliary light, tires, etc.)
should impede the operation of your winch. When mounting, check all vehicle and
winch parts free of obstructions. Be sure that the winch mounting location does not
significantly reduce ground clearance.
WARNING –This winch MUST be mounted with the lid opening at the top.
Improper mounting could damage your winch and void your warranty.
3
SAFETY PRECAUTIONS
⚫AFTER READING AND UNDERSTANDING THIS MANUAL, LEARN TO USE
YOUR WINCH. After installing the winch, practice using it so you will be familiar
with it when required to do so..
⚫ALWAYS STAND CLEAR OF THE WIRE ROPE, HOOK AND WINCH. IN THE
UNLIKELY EVENT OF ANY COMPONENT FAILURE IT’S BEST TO BE OUT OF
HARM’S WAY.
⚫INSPECT ROPE AND EQUIPMENT FREQUENTLY. A FRAYED ROPE WITH
BROKEN STRANDS SHOULD BE REPLACED IMMEDIATELY.
⚫NEVER “move” your vehicle to assist the winch in pulling the load. The
combination of the winch and vehicle pulling together could overload the wire rope
and the winch.
⚫ALWAYS USE HEAVY LEATHER GLOVES when handling rope. DO NOT LET
ROPE SLIDE THROUGH YOUR HANDS.
⚫NEVER WINCH WITH LESS THAN 5 TURNS OF WIRE, 8 TURNS OF
SYNTHETIC ROPE AROUND THE WINCH DRUM since the rope end fastener
may NOT withstand full load.
⚫KEEP CLEAR OF WINCH, ROPE AND HOOK WHEN OPERATING
WINCH. Never put your finger through the hook. If your finger should
become trapped in the hook isolate winch otherwise you could lose
your finger(s). ALWAYS USE THE HANDSAVER when guiding the
wire rope in or out.
⚫NEVER use the winch for lifting people or animals.
⚫Your winch is not intended for overhead hoisting operations.
⚫Maximum working load capacity is on the rope layer closest to the drum. DO NOT
OVERLOAD. DO NOT ATTEMPT PROLONGED PULLS AT HEAVY LOADS.
Overloads can damage the winch and/or the rope and create unsafe operating
conditions. FOR LOADS OVER 1,000 lbs (454 kg), WE RECOMMEND THE USE
OF THE OPTIONAL PULLEY BLOCK TO DOUBLE LINE THE ROPE. This
reduces the load on the winch and the strain on the rope by approximately 50%.
Attach hook to load bearing part. The vehicle engine should be running during
winch operation. If considerable winching is performed with the engine off, the
battery may be too weak to restart the engine.
Double line Single line
⚫Always operate winch with an unobstructed view of the winching operation.
⚫NEVER OBSCURE THE WARNING INSTRUCTION LABELS.
⚫Equipment such as hooks, pulley blocks, straps, etc, should be sized to the
winching task and should be periodically inspected for damage that could reduce
their strength.
⚫NEVER RELEASE FREESPOOL CLUTCH WHEN THERE IS A LOAD ON THE
WINCH.
⚫NEVER WORK ON OR AROUND THE WINCH DRUM WHEN WINCH IS UNDER
LOAD.
4
⚫It is a good idea to use a heavy blanket or winch sail over the wire rope near the
hook end pulling heavy loads. If a rope failure should occur, the cloth will act as a
dampener and help prevent the rope from whipping.
⚫NEVER OPERATE WINCH WHEN UNDER THE INFLUENCE OF DRUGS,
ALCOHOL OR MEDICATION.
⚫ALWAYS DISCONNECT WINCH POWER LEADS TO BATTERY BEFORE
WORKING IN OR AROUND THE WINCH DRUM so that the winch cannot be
turned on accidentally.
⚫Winch should be ISOLATED at all times when not in use.
⚫When moving a load, slowly take up the rope slack until it becomes taut. Stop,
recheck all winching connections. Be sure the hook is properly seated. If a nylon
strap is used, check the attachment to the load.
⚫When using your winch to move a load, if a vehicle is to be used as an anchor
point place the vehicle transmission in neutral, set vehicle handbrake, and chock
all wheels.
⚫NEVER USE THE WINCH TO HOLD LOADS IN PLACE. Use other means of
securing loads such as tie down straps.
⚫ALWAYS USE ONLY FACTORY APPROVED SWITCHES, REMOTE
CONTROLS AND ACCESSORIES.
⚫NEVER MACHINE OR WELD ANY PARTS OF THE WINCH. Such alterations
may weaken the structural integrity of the winch and will void your warranty.
⚫NEVER CONNECT WINCH TO AC supplies as it is dangerous to the winch and
people. DC winches CANNOT be used on mains voltages.
⚫NEVER shock load winch rope otherwise damage will occur internally.
⚫ALWAYS USE caution when pulling or lowering a load up or down a ramp or
incline. Keep people, pets and property clear of the path of the load.
⚫NEVER USE handle on outside of box as a winching anchor.
⚫NEVER hold onto the box handles when winching.
WINCH ASSEMBLY AND MOUNTING
PORTABLE USE
Utility winch can be used in a portable fashion by using the supplied
straps and shackles.
Wrap the rear strap around a tree or secure to an anchor point, secure the two loops
to the two rear shackles on the portable baseplate. ALWAYS be sure that straps do
not contact sharp edges or hot surfaces.
5
PERMANENT MOUNTED USE
The preferred mounting arrangement is to use the four (4) outer bolt holes in the
mounting plate to mount the unit to a surface. To resist the winching loads a minimum
of 1/4” (6mm) mounting plate thickness should be used. Be certain that the structure
used for mounting will resist the winching loads. When using the four (4) bolt mounting
arrangement, the winch’s wire rope may be secured back to the front shackle for
double lining.
4 - Hole Mounting
Pattern dimensions
Using the supplied M10
mounting bolts, washers, and
nuts, tighten the mounting
hardware.
6
(OPTIONAL) PERMANENT MOUNT
For this option, place the winch Freespool in Disengaged, and spool off enough rope
from the winch drum to insert the steel stiffening plate underneath the winch drum, if it
was not Inserted during winch assembly. To resist the winching loads a minimum of
1/4” (6mm) mounting plate thickness should be used. Be certain that the structure
used for mounting will resist the winching loads. Once mounting and wiring is
complete, the winch rope may be powered back onto the drum.
WARNING –WHEN USING THE 2 BOLT MOUNTING OPTION, DO NOT USE
THE FRONT SHACKLE HOLE TO DOUBLE-LINE THE PULL BACK TO THE
WINCH BASEPLATE. IF DOUBLE-LINING WITH THE PULLEY BLOCK, ALWAYS
SECURE THE WINCH HOOK TO A NEARBY STRUCTURE, AND NOT THE WINCH
BASEPLATE.
WIRING DRAWING
WARNING –The location of the Switch MUST NOT Interfere with safe
operation of the vehicle and winch. Wiring MUST NOT come in contact with
any moving parts or sharp edges, such as engine, winch drum, wire rope, straps,
suspension, brakes, exhaust or steering.
Using the supplied M10 mounting bolts,
washers, and nuts, tighten the mounting
hardware.
WINCH2GO
2-Hole Mounting
Pattern dimensions
7
ALWAYS be sure that power and controller cables do not interfere with the
winching operation or tangle the winch operator. ALWAYS keep safety at top
priority.
Apply several layers of electrical tape where wiring may come into contact with
sharp metal parts of the vehicle to prevent insulation abrasion or cutting.
WARNING –Automotive batteries contain gasses which are flammable and
explosive. Wear eye protection during installation and remove all metal jewelry.
Do not lean over battery while making connections.
WINCH WORKING DEMONSTRATION
1. Disengage the clutch by turning the clutch to the “CLUTCH OUT”position.
2. Using the hand saver tool Grab the cable assembly and pull the cable to the desired
length, then attach to item being pulled.
Caution: Always leave at least five turns of cable on the drum;
Reengage the clutch by turn the clutch handle to the “CLUTCH IN”position, as
you need.
3. Insert the switch assembly connector onto the control box.
4. Test-run winch in two directions, each direction for one or two seconds.
5. While standing aside of the tow path, hold and operate the switch assembly supplied
by your choice. To reverse directions. Wait until the motor stops before reversing
directions.
8
6. When the pulling is complete, remove the switch assembly from the female control
socket of the directional valve and replace the female control box socket cover.
REPLACING THE WIRE ROPE
If the wire rope has become worn or is beginning to show signs of strands breaking, it
must be replaced before being used again.
1. Turning clutch to the “CLUTCH OUT”position.
2. Extend cable assembly to its full length. Note how the existing cable is connected
to the drum.
3. Remove old cable assembly and attach new one as the old cable connected to the
drum. Insert the end of the new rope and secure the screw M6x8.
4. Ensure that the new cable wraps in the same rotation direction as the old one.
The cable should leave the drum from the bottom, under the drum.
5. Turning clutch to the “CLUTCH IN”position.
6. Retract Cable Assembly onto drum, first five wraps being careful not to allow
kinking, then winch cable must be wound onto the drum under a load of at least
10% rated line pull.
WARNING - Only replace the wire rope with the identical replacement part
recommended by the manufacturer.
CABLE IN CABLE OUT
Note: Steel winch ropes are not covered by any part of this warranty
and are the sole responsibility of the user to maintain and replace if
necessary.
Table des matières
Autres manuels WARRIOR Treuil
WARRIOR
WARRIOR 5250EN Guide de référence rapide
WARRIOR
WARRIOR SAMURAI S8000 Guide de référence rapide
WARRIOR
WARRIOR 80ENS24 Guide de référence rapide
WARRIOR
WARRIOR 20SPS12 Guide de référence rapide
WARRIOR
WARRIOR 80LDS24 Guide de référence rapide
WARRIOR
WARRIOR T1000-100 Guide de référence rapide
WARRIOR
WARRIOR 50SPS12 Guide de référence rapide
WARRIOR
WARRIOR SAMURAI S8000 Manuel utilisateur
WARRIOR
WARRIOR 135PHS12 Guide de référence rapide
WARRIOR
WARRIOR 260EHLW12 Manuel utilisateur
