WAC Lighting Modern Forms F-RC-WT Manuel utilisateur
OPERATION INSTRUCTIONS
SMART
F-RC-WT
COMPATIBLE WITH
works with the
Google Assistant
Package Contents
Pairing
To pair your remote control:
1. Power cycle your fan by turning o the power at the
circuit breaker.
2. Press and hold and buttons on remote control
for 10-15 seconds.
3. The LED will blink green then remain solid green.
4. The green LED along with audible beeps will indicate
that pairing is successful.
5. Test remote control using the steps in section 2.
1button: Switch between Summer and Winter Mode.
SUMMER MODE (Counter-Clockwise):
A downward airow creates a cooling
eect (FIG. 3). This allows you to set
your air conditioner on a warmer
setting without aecting your comfort.
WINTER MODE (Clockwise):
An upward airow moves
warm air o the ceiling area and
re-distributes the warm air that hovers
around the ceiling to the living space.
This should allow for savings on
heating costs (FIG. 4).
NOTE: To operate the reverse button on your fan,
press the button while the fan is running
Remote Control Operation
Remote Control Button Functions
button: Turns the light ON or OFF.
Press or hold to increase the light level.
Press or hold to decrease the light level.
button: Turns the fan ON or OFF.
Press or hold the button to increase fan speed.
Press or hold the button to decrease fan speed.
NOTE: Your fan features 6 speeds. An audible tone will indicate
when the speed is increased or decreased. When the fan has
reached the minimum/maximum speed level the audible
indication will stop.
2
BatteriesRemote Wall Cradle
Screws
CR2032
CR2032
Unpairing
NOTE: Unpairing must be completed within 3 minutes
of turning the power on to the fan receiver.
1. When you re-engage power to the fans you
want to unpair, press and hold the and
buttons for 4 seconds.
2. The LED will alternate red/green, blink green, and the
receiver will beep to indicate that unpairing is successful.
3
Press and Hold
Press and Hold
NOTE: A maximum of 2 fans can be operated using the
remote control.
FIG.1
FIG.2
FIG.3
FIG.4
FIG.5
Fan Wi-Fi Reset
NOTE: This function only resets the Wi-Fi credentials.
1. Press and hold the and buttons for 6 sec.
2. The LED will light red, blink green,and return to solid
red, and the receiver will beep to indicate that Wi-Fi
reset is successful.
3. After the Wi-Fi resets, the fan will broadcast its service
set indicator (SSID).
45
Factory Reset
NOTE: This will remove remote control and app connections.
Remote Control Factory Reset:
1. Press and hold the ,and buttons
for 10 seconds.
2. The LED will blink red and return to solid red,
and the receiver will beep to indicate that the
factory reset is successful.
Receiver Button Factory Reset
NOTE: This will remove remote control and Modern Forms
app connections.
6
Modern Forms App
NOTE: If you are updating your router,the fan will still
appear in the Modern Forms app but will need to be
re-paired. You can change the name of your fan on the
Modern Forms app upon re-pairing.
FIG.6
FIG.7
FIG.8
Press and Hold
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Supplier’s Declaration of Conformity
Brand name: Modern Forms
Model number: F-RC-WT
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
WAC LIGHTING CO.
44 Harbor Park Drive, Port Washington, NY 11050
Tel: 1-800-810-6615
Rules and Regulations
CAUTION: The user is cautioned that changes or modifications
not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
1. Press the reset button on the receiver until the
receiver control beeps.
2. Power cycle the circuit to complete the process.
Autres manuels WAC Lighting Télécommande
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
