WAC Lighting WT-RT Manuel utilisateur

1 /4

Installation Instructions: WT-RT Recessed Flanged Track System

Safety Instructions:

1. Read all of these instructions before installing the track system.

2. Turn off power at main switch before installing or modifying the system.

3. Do not install within six inches of any curtain or combustible materials.

4. Do not install less than 5 feet above a floor.

5. Do not install in damp or wet locations.

6. Do not install concealed, or extended through building walls.

7. Do not attempt to energize anything other than a track light fixture.

8. This track system shall only be supplied with two single 120V, 60Hz, 20amp branch circuits.

9. Do not load to more than 20 amps per circuit. Although track light systems may seem to operate

acceptably, a dangerous overload of the neutral may occur and result in a risk of fire.

10. Check with a qualified electrician before wiring.

11. All of the installations shall be in accordance with NEC and all local codes.

12. Save these installation instructions and refer to them when additions or changes to the track

configuration are made.

A: Strap Mounting

zRemove the End Cap and save.

zSlide the perforated hanger straps（not

included，can be purchased in a hardware

store）into the groove in the side of the track.

An equal number of straps should be mounted

on each side of the track.

zWrap the straps around the building structure

or nail the straps to the structure. They should

be positioned evenly to balance the track.

zPlacing one hanger strap every foot, per side

is recommended.

zPush End Cap into the track at the end of the

track and secure by screw.

zThe hanger strap can be bought at a hardware

store, recommend size is 11/16 inch (17mm)

in width.

B: Direct Mounting

zMounting slots in top of track can be knocked

out and are spaced every 10 inches for

convenience.

zMounting as shown using a mounting screw

every 2 feet is recommended.

zAdditional supports may be added for heavier

loaded applications.

Generally, for any mounting method, do not exceed 4 feet between mounting points, and do not

exceed 6 inches (for 4 feet of track or less in length) or 12 inches (for track that is greater than 4 feet)

from each end of the single track section. Always use two or more mounting supports for each track

length.

Mounting options

Ceiling Channel

Hanger Strap

Ceiling Structure

Mounting Screw

2 /4

Feed options

Live End Connector can be fed directly

from above using a 1/2 inch or 3/4 inch

electrical connector.

zMake sure power is off before wiring.

zNote the polarity indicator of the track and

accessories

zRemove cover and save.

zRemove knockout in top plate.

zSecure conduit by conduit connector (1/2 or 3/4

size recommended) to top plate and lock the

nut.

zPass wires（12AWG）through conduit and

connector .Cut and strip each end of the wire,

then a single conductor is clamped directly

under the head of the screw when it is

tightened. The single conductor is bent around

the screw in a 3/4 loop, insert the wires to the

corresponding terminals (see fig. below) and

secure tightly with a screw.

zSecure the track to the ceiling (see mounting

options on previous page).

zReplace the cover.

zInsert the spline and secure to the track with two

screws.

C: Suspension Mounting

zSlide or snap the hanger clips (WMT-RT) onto

the track, and space the clips evenly along the

track length.

zSecure the bolt and make sure the hanger clips

tightly hook in the track groove.

zAssemble the stem or cable suspender（refer to

WT/WHT track suspension system）to the

hanger clips. Level track and secure to building

structure.

zRecommended: two clips for 4' track, three clips

for 8' track, and four clips for 12' track. Always

use more than one clip for each track length.

Additional clips may be added for more support.

To Building Structure

Hanger Clip

Bolt

Knock out

Conduit Connector

(1/2” or 3/4”)

Conduit

Electrical Wire

(

5-12AWG

)

Lockin

Nut

Scre

Cover

End Ca

3 /4

Earth InsideMODEL: WLLC-RT Earth Outside

MODEL: WRLC-RT

L1 N1

N1 L2

Over Impediment

Accessory options

zMake sure power is off before connecting.

zNote the polarity indicator of the track and

accessories.

zInsert the spline to the track groove and

secure with two screws.

Mini coupler or

“I” Connector Power Jum

Power Feed

Structural Im

ediment

Live End Connecto

Live End Connector

MODEL: WEDL-RT MODEL: WEDR-RTEarth Left Earth Right

MODEL: WPC-RT

Track Unit

Mini Cou

line

4 /4

N2N2

N1 L2

L2 N1

N1 L1 L2

Earth LeftMODEL: WLTC-RT

MODEL: WIC-RT

Earth Right

MODEL: WRTC-RT

MODEL: WXC-RT

Field Cutting and Field Drilling

Remove the end cap and save.

Use a metal cutting power saw (preferably in a

miter box) to cut the track, insulation material,

and copper bus bars vertically with one

straight cut.

If the mounting openings are not in the proper

position to secure after field cutting, use a

power drill to drill an appropriate number of

mounting holes. The holes should be 3/16” in

diameter, and drill in the top centerline of the

track along the track length.

CAUTION: Remove any burrs that may

have resulted from the cut or drill. There

should be no burrs between the copper

wires and the aluminum track housing.

Replace the End Cap at the end of track and

secure with a screw.

2N2N

Cut Flush

44 Harbor Park Drive

Port Washington, NY 11050

800.526.2588

www.waclighting.com

Table des matières

Autres manuels WAC Lighting Équipement d'éclairage

WAC Lighting

WAC Lighting 5221 Manuel utilisateur

WAC Lighting

WAC Lighting WS-90627 Manuel utilisateur

WAC Lighting

WAC Lighting Paloma MO-LED512 Manuel utilisateur

WAC Lighting

WAC Lighting InvisiLED CCT 100 Manuel utilisateur

WAC Lighting

WAC Lighting dweLED 299-LED Wall Sconce Manuel utilisateur

WAC Lighting

WAC Lighting HR-3LED-H20A Manuel utilisateur

WAC Lighting

WAC Lighting LD-700MA03-EDIM-IS Manuel utilisateur

WAC Lighting

WAC Lighting LD-700MA03-EDIM-IS Manuel utilisateur

WAC Lighting

WAC Lighting Falcon Series Manuel utilisateur

WAC Lighting

WAC Lighting GATE 12V Manuel utilisateur

WAC Lighting

WAC Lighting LED-TC Series Manuel utilisateur

WAC Lighting

WAC Lighting H-LED160 Manuel utilisateur

WAC Lighting

WAC Lighting M6000-STAKE Manuel utilisateur

WAC Lighting

WAC Lighting InvisiLED Classic LED-T24 Manuel utilisateur

WAC Lighting

WAC Lighting Silo X10 Manuel utilisateur

WAC Lighting

WAC Lighting HTK-793 Manuel utilisateur

WAC Lighting

WAC Lighting dweLED FM-96916 Manuel utilisateur

WAC Lighting

WAC Lighting BA-FT08-WT Manuel utilisateur

WAC Lighting

WAC Lighting LED-350MA03-RB Manuel utilisateur

WAC Lighting

WAC Lighting WTK-6010 Series Manuel utilisateur

WAC Lighting

WAC Lighting Modern Forms 708-LED Manuel utilisateur

WAC Lighting

WAC Lighting 6011 Manuel utilisateur

WAC Lighting

WAC Lighting Volta 2" LED Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur