VStarcam C7837WIP Manuel utilisateur
w w w . v starcam. c om
User manual
1. Software download
① Go to www.eye4.so to download the APP.
② Search Eye4 in APP Store, Android market etc.
③ Scan the QR code below to download.
2. Register
① For Android/iOS APP, click on "Register now",
create a user name and password to nish register.
② Also support the third party account login( no need
to register).
3. Add cameras to the network
Note: If it failed to add the camera by the
'Scan QR code' , please choose the Method Two
in the 'Others' to add the camera.
3.1 Scan QR Code
Please power on the camera, wait until the reboot
of the camera finished(it takes about 30 seconds),
then the camera will say " Please use APP for wifi
conguration"or "WiFi conguration is waiting" ( If the
camera doesn't say anything, please reset the camera
to factory default settings by holding the reset button
for 10 seconds, then it will say "reset completed,
device will reboot soon" ).
① Enter the APP ,click the "+"on the top right corner,
click on "Scan QR Code"，to scan the QR code on the
camera's body ;
②Once the camera says "Please use APP for wifi
configuration" for the first time, please click on
the "Heard voice prompt" button, then put in the
password of the WiFi network that the mobile phone
currently connecting to, click'confirm'to go to next
step.
③ During the configuration, please keep the phone
and the camera within 2 meters (at this time, please
maximize the volume of the mobile phone).Click the
'Send'button on the APP, to send conguration signal
to the camera.
④ After the camera prompts "wireless conguration
succeed," please wait about 10 seconds, the APP
will show the "Add Camera" page, click on the it to
complete the adding.
Note: Place the phone close to the camera, and
adjust the phone volume to maximum
Note: During this process, if it prompt that wifi
configured successfully but the binding page does
not pop up, please return to the Add Camera page,
to select 'Others' → 'IP Camera' → 'Search in LAN' or
"Manually add" to bind the camera.
3.2 Other ways of adding
If no QR code can be found on the body of the
device, please choose the 'Others ' to add the
camera.
Method One:
① Enter the APP ,click the "+"on the top right corner,
choose 'Others' → 'IP Camera'.
② Choose 'Wireless Installation', please refer to the
'Wireless conguration add instructions'and the APP's
voice prompt to nish the setting.
Note: Please refer to the ② ③ ④ steps in the
'Scan QR code' above to finish the'Wireless
Installation'settings.
Note: During this process, if it prompt that wifi
congured successfully but the binding page does not
pop up, please return to the Add Camera page,select
the'Search in LAN'or "Manually add" to bind the
camera.
Method Two:
① Please power on the camera, and use network
cable to connect camera with the router LAN port,
make sure the router yellow indicator is flashing；
then choose the " Search in LAN" or " Manually add"
method in the'Others'to add the camera.
Please make sure the phone and camera are
under the same router.
② Login the APP, click on the "+" in the top right
corner,choose'Others' → 'IP Camera'.
Search Camera in LAN：
① Click on "Search in LAN", you can find all the
available cameras in the same router with the
smartphone. If added successfully, the camera can be
added via the same way by other users(with dierent
account).（Note：Cameras that has been added
successfully in this account will not be searched
again）.
Table des matières
Autres manuels VStarcam Caméra de sécurité
VStarcam
VStarcam C38S Manuel utilisateur
VStarcam
VStarcam WM2 Manuel utilisateur
VStarcam
VStarcam C Series Manuel utilisateur
VStarcam
VStarcam Pangolin T series Manuel utilisateur
VStarcam
VStarcam C38S-P Manuel utilisateur
VStarcam
VStarcam C18S Manuel utilisateur
VStarcam
VStarcam CB72 Manuel utilisateur
VStarcam
VStarcam FC2 Manuel utilisateur
VStarcam
VStarcam CS49 Manuel utilisateur
VStarcam
VStarcam C24S Manuel utilisateur
