VRL PAR-363 Manuel utilisateur

TABLE OF CONTENTS

INTRODUCTION .............................................................................................2

MAIN FEATURES......................................................................................3

UNPACKING..............................................................................................3

SAFETY WARNING.........................................................................................3

PANEL REVIEW ..............................................................................................4

INSTALLATION AND SETTING.......................................................................4

1. MULTI-FIXTURES CONNECTION ........................................................4

2. LAMP BODY INSTALLATION................................................................5

2. DMX CHANNEL SUMMARY .................................................................5

3. CHANNEL FUNTIONS ..........................................................................6

4. ABOUT EACH CHANNEL.........................................................................................7

MAINTENANCE.............................................................................................10

1.TROUBLESHOOTING..........................................................................10

TENICAL SPECIFICATION............................................................................11

INTRODUCTION

Thank you for purchasing the VRL PAR-363 High Power Par Lamp. There are three

operation modes available –

•Auto

•sound–activation

•master/slave

The PAR-363 also features 8 built-in programs. The product has a long lifespan and low

power consumption. Before you begin, please read instructions carefully. If you should

have any problem please contact your nearest distributor.

MAIN FEATURES

■DMX-512 control, 6 channels

■DMX, AUTO, SOUND-ACTIVE, MASTER/SLAVE

■RGB control with 255 grades

■RGB total dimmer is 0~100%

■Shutter speed is 10flashes/sec ~10secs /flash

■36X3W LED

UNPACKING

•VRL PAR-363 High Power Par Lamp

•USER MANUAL

SAFETY WARNING

For your convenient and accurate operation, please read the following information

carefully.

•Suitable for indoor use only.

•Put it in a dry, well -ventilated place in case of short cut caused by erosion of

moisture and rain.

•Do not install nearby hot sources in case that rising temperature of lamp damages

itself.

•Do not barrier vent in order to ventilate well and dissipate in time.

•Connect the fixture with power source, which has a ground line, and voltage of

power source should accord with rating voltage.

•If fuse was damaged, change the same type.

•You can only choose accessories the manufacturer provides when need repairing.

Ambient temperature of the lamp should not exceed 40°

•If any problem, contact with professional technicians working in our after-sales

service department.

PANEL REVIEW

Press FUN button: Switch to function menu or return to previous menu

Press UP/DOWN: Adjusts the currently activated field. The four points will blink indicating

a value change.

Press ENTER: Enter into sub-menu or confirm the current value.

INSTALLATION AND SETTING

1. MULTI-FIXTURES CONNECTION

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain

connection is where the DATA OUT of one fixture connects to the DATA IN of the next

fixture. The order in which the fixtures are connected is not important and has no effect on

how a controller communicates to each fixture. Use an order that provides for the easiest

and most direct cabling. Connect fixtures using shielded two conductor twisted pair cable

with three pin XLR male to female connectors.

The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive

(S+).

2. LAMP BODY INSTALLATION

Notes: do not install it nearby the curtain or flammable materials.

Only for indoor use.

OPERATION

1.SET DIPSWITCHES

■Each fixture occupies 6 DMX channels.

■DMX 512 signal can control multi-fixtures together, however you must set the DMX

address of each lamp first. Different DMX address will lead to different movements.

■You can set DMX address from 1~506 on the multi-function display panel.

■Switch on power supply and after finishing resetting, the panel will show 001,that is to

say DMX address is 1 and the first lamp has been controlled by 1~6 channels. In turn the

second fixture has been controlled by 007~012 channels. (When panel shows 001,press

UP button until it shows 007.Then just press ENTER button). In the same way, the third

fixture has been controlled by 013~018 channels and the panel shows013.

■Through this method, you can control multi-fixtures to perform different movements.

2. DMX CHANNEL SUMMARY

3. CHANNEL FUNTIONS

DISPLAY FUNCTION

VALUE 001-506 DMX address

MODE M-DM DMX mode

M-AU AUTO mode

Notes: Only one lamp can be set as Master and the left are

Slaves (Slaves set to DMX mode with DMX address “001”). Do

not connect the Slaves lamp with controller.

M-SO SOUND mode

Notes: Only one lamp can be set as Master and the left are

Slaves (Slaves set to DMX mode with DMX address “001”). Do

not connect the Slaves lamp with controller.

PRCO PR1~8 8 built-in programs

Pr1-4 means skip

Pr5-8 means fade

SPCO SP01~15 Auto speed SP01: 0.1sec/step, SP15: 10secs/step

TEST ALL Check all channels with motors

RED Check red channels

GREEN Check green channels

BLUE Check blue channels

DSPL STND Display bites normally

REV Display bytes upside down

REST REST/ON Reset

(Press ENTER button to enter into REST menu and the screen

reads flashing “REST”. Then press UP/DOWN button and the

screen reads flashing “ON”. If you press ENTER again, the light

engine resets again)

4. ABOUT EACH CHANNEL

■Channel 1:DMX MODE

Ch DMX Function CH2 CH3 CH4 CH5 CH6

CH1

0~24 RGB Red

0~255 Green

0~255 Blue

0~255 Strobe

Speed

0~255

Dimmer

0~255

25~49 Built-

in program

function No

function

Auto

speed No

function

50~74 Built-

in program

75~99 Built-

in program

100~124 Built-

in program

125~149 Built-

in program

150~174 Built-

in program

175~199 Built-

in program

200~224 Built-

in program

225~255 Sound-active

program No

function

■Channel 2: RED

When CH1 is 0~24

DMX value red

255 carmine

0 0

■Channel 3：GREEN

When CH1 is 0~24

DMX value green

255 bottle green

0 0

■Channel 4:Blue

When CH1 is 0~24

DMX value blue

255 navy blue

0 0

■Channel 5：Strobe

When CH1 is 0~24

DMX value strobe speed

255 slowest

16 fastest

15 no strobe

0 no strobe

Notes: CH2~4 decides brightness. When CH2, CH3, CH4 is 0, there is no

brightness.

When CH1 is 25~224:

DMX value AUTO speed

255 slowest

0 fastest

■Channel 6：RGB Dimming

When CH1is 0~24:

DMX value RGB brightness

255 0

0 brightest

MAINTENANCE

1.TROUBLESHOOTING

Problem Probable cause(s) Suggested remedy

Fixtures does not work

No power source Check if power source is on or

cord works well.

Fuse burnt

Cut off power source and change

the same type fuse. If fuse was

burnt on end, it may be the

problem of connection; Find

qualified professors to repair.

Reset normally, but console

abnormally or no response

False or incomplete

data connection

Check, repair or change the data

line. Ensure connection is well

and the first lamp’s single input is

connected with the controller

output.

False address setting Check DMX address.

roblem of signal

connector of some

fixtures

Pull out the signal output and

input of one fixture. Then connect

both directly. If it works well, this

fixture is proved to be the failed

one. Handle the rest fixtures alike

to check which fixture has

problems. If any problem, please

connect the technician.

Table des matières

Autres manuels VRL Matériel de DJ

VRL

VRL WASH-493 Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur