Vostok CERES Manuel utilisateur
CERES
HIGH-CLASS LINEAR VCA & MIXER
User Manual
LIMITED WARRANTY
Vostok Instruments warrants this product to be free of defects in material or
construction for three years from the date of purchase (invoice required).
During that period, any malfunctioning unit will be repaired, serviced, and calibrated
on a return-to-factory basis, with the customer paying the transit cost to Vostok
Instruments.
Malfunctions resulting from wrong power supply voltages, backward or reverse power
connections, abusive treatment, removing knobs, or any other obvious user-inflict
faults are not covered by this warranty, and regular rates will apply.
Vostok Instruments implies and accepts no responsibility for harm to persons or
apparatus caused through the operation of this product.
The device intended for repair or replacement under warranty should be shipped in
the original packaging only. Vostok Instruments can not take any responsibility for
damages caused during transport. So before sending us anything, contact us at
INSTALLATION
Ceres needs a power supply capable of providing 50mA on each of the +12V and
-12V rails, and 10HP of free space in your case. We strongly recommend you to check
the current consumption of your system on the ModularGrid website and your power
supply capabilities before plugging in the module.
To install it, turn your case off and connect the supplied power cable to both the
module and your Bus Board, minding the polarity so that the RED Stripe on the cable
is oriented to the -12V line on both the module and the Bus Board. Please refer to
your case manufacturers’ specifications for the location of the negative supply.
Always turn your case off before plugging and unplugging any Eurorack module.
1
INTRODUCTION
If you have been already into the Eurorack world for a while, I’m sure you have heard
the sentence: “you never have enough VCAs” more than once.
As an electronic musician, this has always been present. I can’t count how many times
I needed an extra VCA with all of them already being used.
I wanted to create an all-around, good-sounding, and handy VCA, small enough to fit
on little systems but with a good amount of channels and functionality. And this is
what Ceres is.
Its core, the 3360, has been used for years in dozens of devices with remarkable
performance. Sum it to a carefully designed 4-layer PCB layout, and we get a super
quiet VCA in terms of noise and CV bleeding.
The combination of daisy-chained inputs and mixed outputs achieves a vast range of
possibilities. Several CV signals can modulate a unique source with every output
mixed back at the final stage to create new waveforms and open the door to
experimentation.
TECHNICAL SPECIFICATIONS
-Size: 10HP
-Current draw: +/-12V: 50mA, +5V: 0mA
-Depth: 30mm (including power cable)
-Unity Gain CV Level: 5V
-Input Impedance: 100kΩ
-Output Impedance: 1kΩ
2
OVERVIEW
1. Signal Input: The signal plugged here is
daisy-chained to the next channel input.
2. CV Input: Unipolar (positive) signals are
expected here. Unity gain voltage: 5V
3. Signal Output.
4. LEVEL Pot: Control over the circuit’s gain. With
a signal present at CV, it works as an attenuator
of that signal.
5. LED Indicator: shows the output signal
amplitude.
GETTING STARTED
Ceres counts with six identical channels of Voltage Controlled Amplifiers (VCA).
Each channel is composed of two inputs, one output, Level control, and an LED
indicator. The signal inputs are daisy-chained, so every channel receives the signal of
the previous channel if no other is present at its input. On top of that, every channel is
mixed at channel six if no cable is plugged into its output.
Despite its simple layout, Ceres offers a good amount of functionality to experiment
with, so let’s take a deeper look.
3
FUNCTIONAL MAP
VCAs
On each Ceres channel, the amplitude of the signals present at IN is controlled by a
second signal, plugged at CV. The LEVEL pot adjusts how much of the CV signal will
be injected into the VCA, and by correlation, the system's gain.
To keep signals pristine, Ceres channels don’t amplify them. The maximum gain
achieved by Ceres VCA circuits is equal to the original amplitude. To get that, we
need a CV signal of at least 5V. Higher CV signals will be clipped at 5V and can be
adjusted with the LEVEL pot to correct its shape.
If no CV signal is present at the CV
Input, the LEVEL pot works as a volume
control, matching the signal unity gain
at its fully clockwise position.
Ceres VCAs follow a linear response,
which means that the shape of the CV signals used will be intact, and the dynamic of
the signal will match the exact contour of our CV.
Daisy-Chain Operation
By default, Ceres sends the signal present at each signal input (IN) to the next one. To
break the chain, patch a cable on the desired input. This implementation allows one to
control one source with different CV signals.
Mixing Stage
On Ceres, every output is mixed at channel six output. The circuit allows you to
extract channels from the mix by patching a cable on the desired channel output. In
combination with the daisy-chained inputs, the mixing stage achieves a vast range of
possibilities: from simple signal amplification and clipping to the creation of new
waveforms.
4
Table des matières
Autres manuels Vostok Équipement d'enregistrement
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
