VonHaus 3500023 Manuel utilisateur
600W DUAL
ACTION POLISHER
WITH ACCESSORY
SET
3500023 - Instruction Manual
CONTENTS
Safety Instructions 1
Safety Instructions 2
Safety Instructions/Safety Symbols 3
Technical Specification/Product Specification 4
Before First Use 5
Before First Use 6
Operation 7
Adjusting the Rotation Speed/Applications 8
Handling Techniques 9
Polishing Tips/Common Mistakes to Avoid 10
Cleaning & Maintenance/Troubleshooting 11
Warranty 12
GENERAL SAFETY INFORMATION.
WARNING! Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
Please retain all warnings and instructions
for future reference.
The term “power tool” in the warnings
refers to your mains-operated (corded)
power tool or battery-operated (cordless)
power tool.
WORK AREA SAFETY.
Keep your work area clean and well lit.
Cluttered or dark areas invite accidents.
Do not operate power tools in explosive
atmospheres such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children and animals
away while operating the power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY.
Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adaptor plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce risk
of electric shock.
Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
Do not expose power tools to rain or wet
conditions. Water entering the power tool
will increase the risk of electric shock.
Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
1
the power tool.
Keep the cord away from heat, oil, sharp
edges and moving parts. Damaged or
entangled cords increase risk of electric
shock.
When operating a power tool outdoors,
use an extension cord suitable for outdoor
use to reduce the risk of electric shock.
PERSONAL SAFETY.
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence or
drugs, alcohol or medication. A moment
of inattention while operating power tools
may result in serious personal injury.
Use personal protective equipment.
Always wear eye protection. Protective
equipment such as a dust mask, non-
skid safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to the power source and/
or battery pack, picking up or carrying
the tool. Carrying power tools with
your finger on the switch or energising
power tools that are switched on invites
accidents.
Remove any adjusting key or wrench
before turning the power tool on. A
wrench or key left attached to a rotating
part of the power tool may result in
personal injury.
Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
Dress appropriately. Do not wear loose
clothing or jewellery. Keep your hair,
WARNING
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE
WARNING
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE
clothing and gloves away from moving
parts to prevent them from becoming
caught in the tool.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure that these are connected and
properly used to reduce dust-related
hazards.
POWER TOOL USE AND CARE.
Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
Do not use the power tool if the switch
does not turn it on and off. A power tool
that cannot be controlled with the switch
is dangerous and must be repaired.
Disconnect the plug from the power
source and/or the battery back from
the power tool before making any
adjustments, changing accessories or
storing. Such preventative safety measures
reduce the risk of starting the power tool
accidentally.
Store idle power tools out of reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
Maintain the power tool. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
This tool is not intended for use by
persons with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instructions
concerning use of the tool by a person
responsible for their safety.
Children should be supervised to ensure
they do not play with the tool.
SERVICE.
Have your power tool serviced by a
qualified repair person using identical
replacement parts only to ensure that the
safety of the power tool is maintained.
ADDITIONAL SAFETY INFORMATION.
WARNING Know your Polisher. Do not
plug the tool into the power source
until you have read and understand
the information in this Instruction
Manual. Learn the tool’s applications
and limitations, as well as the specific
potential hazards related to this tool to
reduce the risk of electric shock, fire or
serious injury.
Always wear eye protection. Any power
tool can throw foreign objects into your
eyes and cause permanent eye damage.
Always wear safety goggles (not glasses)
that comply with ANSI safety standard
Z87.1. Every day glasses have only
impact resistant lenses. They are not
safety glasses.
WARNING Wearing glasses or goggles
not in compliance with ANSI Z87.1 when
operating this tool could cause serious
injury.
WARNING Only use accessories
designed for use with this Polisher.
WARNING
3
WARNING If any part is missing or
damaged, do not plug the tool into the
missing or damaged part is replaced.
Failure to follow this instruction could
result in serious personal injury.
SAFETY SYMBOLS
PLEASE READ & UNDERSTAND THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE
REFERENCE
The use of improper accessories may
result in injury to the operator or damage
the tool.
Read and understand the
Instruction Manual before use.
Always refer to Instruction
Manual if in any doubt of
operation, maintenance and
care.
Always wear protective gloves.
Wear a dust mask
Always wear eye
protection.
Do not use in wet/adverse
weather conditions.
TECHNICAL SPECIFICATION
PRODUCT SPECIFICATION
230-240
V
VOLTAGE
600
W
RATED
POWER
1500-6800
min-1
NO LOAD
SPEED
1. Backing Plate
2. Soft Polishing Pad (Black)
3. Speed Adjuster (see page 8)
4. Front Grip
5. Power Switch
6. Adjustable ‘D’ Handle
7. Side Vents
50
FREQUENCY
Hz
1
8. Locking Spanner
9. Hex Bolts (x2)
10. Hex Key
11. Hard Polishing Pad (Red)
12. Medium Polishing Pad (Yellow)
13. Medium Polishing Pad (Yellow)
14. Spindle (see page 6)
15. Rotation Speed Dial (see page 8)
16. Microfibre Cloth (not shown)
17. Polishing Mitten - Dry Finish (not
shown)
2
45 6
7
8
910
11
12
13
15
BEFORE FIRST USE
ASSEMBLING THE ADJUSTABLE D HANDLE
The ADJUSTABLE D HANDLE (6) must be fitted to the machine before use:
• Use the HEX BOLTS (9) provided to fit the ADJUSTABLE D HANDLE (6) via the fixing holes to either side
at the front of the Polisher.
• Use the supplied HEX BOLTS (9) to tighten the bolts that secure the handle in position.
IMPORTANT Always ensure the Polisher is disconnected from the mains supply before
performing any maintenance, cleaning or assembly tasks.
6
9
5
10
FITTING THE BACKING PAD
The Backing Pad must be securely fitted to the SPINDLE (14) before use:
• Use the LOCKING SPANNER (8) to hold the SPINDLE (14) thread secure
• Rotate the BACKING PLATE (1) in a clockwise direction to secure the BACKING PAD (1) to the
SPINDLE (14) assembly.
• To remove, use the LOCKING SPANNER (8) to hold the spindle thread secure. Rotate the
BACKING PAD (1) in an anti-clockwise direction to remove.
BEFORE FIRST USE
IMPORTANT Always ensure the Polisher is disconnected from the mains supply before
performing any maintenance, cleaning or assembly tasks.
8
1
14
OPERATION
WARNING Always use adequate protective equipment, including eye protection, respiratory protection
and hearing protection, when working with this tool.
• Connect the machine to the mains power supply.
• To start the machine, slide the POWER SWITCH (5) to the I(on position). The motor will start and take a
few moments to reach full operating speed.
• To stop the machine, slide the POWER SWITCH (5) to the 0(off position).
7
NOTE This Polisher is fitted with a Soft Start Function to help spread polish slowly before going to full
speed.
WARNING! Always wait until the machine has come to a standstill before putting it down to rest.
5
On
Off
Table des matières
Autres manuels VonHaus Sander
