Volth S-AC100 Manuel utilisateur
S-AC100
Non-Contact AC Voltage Detector
Non-Contact
AC Voltage Detector
S-AC100
S-AC100
50 to 1000V AC detection with flashlight
S-AC100
TABLE OF CONTENTS
1. APPLICATIONS GENERAL
2. FRONT PANEL DESCRIPTION
3. SAFETY INFORMATION ( Read First)
4. SPECIFICTIONS&WORK DATA
5. OPERATING INSTRUCTIONS
6. BATTERY REPLACEMENT
TABLE OF CONTENTS
1. APPLICATIONS GENERAL
The Volt finder voltage detector is intended to check for
the presence of AC voltage, check for the presence of
display radialization, signaling the user with a LED and
Buzzer on. Built-in bright flashlight.
2. FRONT PANEL DESCRIPTION
● 1-------Back flashlight
● 2-------Flashlight switch ON/OFF
● 3-------Battery cover & compartment
● 4-------OFF/ON host switch
● 5-------Detector VoltBeat
3
1
5 4 2
3. SAFETY INFORMATION ( Read First)
Warning
To avoid possible electric shock or person injury:
1) Do not use if VoltBeat is not flashing.
2) Do not use if Tester appears damaged or if the
Tester is not operating properly. If in doubt, have
the Tester serviced.
3) Do not apply more than the rated voltage as
marked on the Tester.
4) Use caution with voltage above 30V ac as a
shock hazarded may exist.
5) Comply with local and national safety requirements.
6) Use proper protective equipment as required by
local or national authorities.
7) Before each use, verify operation by testing a
known working circuit that is within the rating
of this unit. Steady red glow (not flash) indicates
voltage present. If no indication, voltage could
still be present. Do not rely on this tester with
shielded wire. Operation may be affected by
differences in socket design and type. If this
product is used in a manner not specified by the
manufacture, protection provided by the product
may be affected.
- Double insulation
4. SPECIFICTIONS & WORK DATA
Detection voltage range 50V AC to 1000V AC
Power 3V (AAA*2)
Operating temperature –10˚C to 50˚C (14˚F to 122˚F)
Storage temperature –10˚C to 50˚C (14˚F to 122˚F)
Humidity 95% (0˚Cto40˚C (32˚F to 104˚F))
Altitude 3000m
Contaminated distinction II
Weight 48.5g
Max work current 32mA
Max off current 0.08uA
5. OPERATING INSTRUCTIONS
1) Turning the unit on
Momentarily press the blackЭ button. Listen for a
double beep to confirm activation of the unit.
A continual VoltBeat flash visually indicates the
unit is active
2) Turning the unit OFF
Press and hold the black Эbutton for more than 1
second. Listen for a long 1 second beep to confirm
deactivation of the unit. The absence of the VoltBeat
flash indicates the unit is inactive
3) VoltBeat(system self test)
VoltBeat is a self –test feature for visually confirming
battery and system integrity, and power-on. It provides
once flash every 1 second during normal operation.
4. SPECIFICTIONS & WORK DATA
Detection voltage range 50V AC to 1000V AC
Power 3V (AAA*2)
Operating temperature –10˚C to 50˚C (14˚F to 122˚F)
Storage temperature –10˚C to 50˚C (14˚F to 122˚F)
Humidity 95% (0˚Cto40˚C (32˚F to 104˚F))
Altitude 3000m
Contaminated distinction II
Weight 48.5g
Max work current 32mA
Max off current 0.08uA
5. OPERATING INSTRUCTIONS
1) Turning the unit on
Momentarily press the blackЭ button. Listen for a
double beep to confirm activation of the unit.
A continual VoltBeat flash visually indicates the
unit is active
2) Turning the unit OFF
Press and hold the black Эbutton for more than 1
second. Listen for a long 1 second beep to confirm
deactivation of the unit. The absence of the VoltBeat
flash indicates the unit is inactive
3) VoltBeat(system self test)
VoltBeat is a self –test feature for visually confirming
battery and system integrity, and power-on. It provides
once flash every 1 second during normal operation.
4) Checking for the presence of AC voltage &
radialization
Placing the tip of the unit near an AC voltage and
display produces a steady glow at the tip and
(if enabled) a continual beep
5) Auto power off
After about 3 minutes of non-use, the unit automatically
performs a power off to save batteries. A longer beep
provides an audible indication of the event.
The absence of the VoltBeat flash serves as a visual
power-off indication
6) Flashlight on & off
Press and hold the back black button for flashlight
on, if button undo for flashlight off
6. BATTERY REPLACEMENT
When the battery voltage drops below 2 volts VoltBeat
provides a visual indication by stopping the VoltBeat
flash. Replace with 2 AAA batteries. Slide the battery
cover (○3/Fig) and remove the battery. Make sure the
battery cover is secure after changing the battery.
NOTE : If it will be not in use for long time, please
remove battery.
Table des matières
Autres manuels Volth Capteur de sécurité
