VOCHE VH124 Manuel utilisateur
Model No: VH124
2000W WEED BURNER
IMPORTANT SAFETY WARNINGS & CAUTIONS
Read all instructions and warnings carefully before use and retain for future reference.
WARNING: in order to avoid overheating do not cover or obstruct the air vents on the
weed burner.
Exercise due care in use as surfaces and components can become very hot.
The Weed burner has no user serviceable parts, check regularly for cord wear and
other signs of damage.
Do not operate if the cord is damaged or worn, or if the Weed burner has been
dropped or damaged.
If an extension cable is used with the weed burner, then the extension cable should
have a minimum rating of 10A and 2000W. If a cable reel is used, then it should be
unrolled entirely.
All repairs and replacements should be carried out by a qualified electrician or the
unit should be returned to the retailer.
This appliance can be used by children from the age of 8 and above and persons
with reduced physical, sensory or mental capabilities or lack experience and
knowledge if they have been given supervision on instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not
be made without supervision.
Keep work area clean and well lit.
Do not operate weed burner in the presence of flammable liquids, gasses or dust.
Personal safety:
Stay alert, watch what you are doing and use common sense when operating the
weed burner.
A moment of inattention while operating Weed Burner may result in serious
personal injury.
Wear personal safety equipment and always wear safety glasses.
Wearing personal safety equipment such as dust mask, shoes with non-slip soles,
safety helmet and ear protection, appropriate to the use of the device, will reduce
the risk of personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
Components:
OPERATION:
Assemble the extension handle
Slide the extension tube into the device as far as possible; until it clicks into place
(there is only one way to do this). Slide the other end of the extension tube into the
handle until the small catch pushes through the small hole. Check that both ends of
the tube are immovably in place. Press the ‘extension tube lock button’ or the ‘handle
lock button’ and pull the tube out of the device and the handle.
To install the nozzle:
The nozzle(8) can easily be pushed over the hot air nozzle.(4)
The protruding points of the ‘weed burner’ nozzle must be pushed fully into the
slots of the burner nozzle.
The nozzle must then be twisted approximately one centimeter into the slot.
Attention! The long side of the cap must be on top (this is the side where the switch is
located)
Never touch the nozzles during or immediately after use of the device. The nozzles are
very hot.
Temperature settings:
With the on/off- and power switch you can select from two temperature settings.
Depending on the application, you can use the following settings:
Setting I 60 °C (venting / cooling)
Setting II 650 °C (weed burning) the volume of air in each setting 500 l/minute
Always use with caution! Do NOT cover the ventilation openings during use as it
causes a risk of burns! Never touch the hot nozzle!
Start to use
Check that all of the relevant safety measures have been implemented.
Ensure the extension handle is firmly fixed onto the device and that the device is
turned off.
Lead the electrical cable away from the burner nozzle through the cable clamps on
the extension tube and handle.
Install the nozzle to destroy weeds.
Insert the plug into the socket and turn it on.
Check to ensure the nozzles and air vents are not blocked before turning the device
on.
Slide the on/off and power switch to Setting II: the device will start to warm up.
Allow the device about 45 seconds to warm up to full heating capacity.
To eliminate weeds, hold the nozzle over the weeds for around 5 seconds. During
these 5 seconds the cell structure of the weed is destroyed. As a result, the weed
dies within a few days.
It is not necessary to completely burn the weeds, 5 seconds is more than sufficient.
For an efficient treatment the nozzle should be held around 0 to 5 cm above the
weeds.
The effects are not visible immediately but will take a while before they can be seen.
It is more of a long-term effect.
Cooling and permanent switching off:
Before turning off the device permanently, it must be cooled first.
Select temperature Setting I and operate for at least one minute. Allowing the
machine to cool down.
Once cool the Weed burner can be switched off.
During cooling down the appliance can be placed on its stand to allow it to cool
down before storage.
Never leave the appliance unattended until completely cool.
Do not use your hand other body parts to check the temperature of the nozzles.
EXPLANATION OF THE SYMBOLS
Risk of personal injury, loss of life or damage to the tool in case of non-observance of the
instructions in this manual.
Indicates electrical shock hazard.
Do not expose to rain.
Remove plug from the mains immediately if the cable is damaged.
Caution, hot surface.
Technical Specifications
Model No: VH124
Voltage: 230v / 50Hz
Power Rating: 2000W
Temperature: 2 Setting - 60`C - 500L / Min, 650`C - 500L / Min
Air Flow: 500L / Min
This product conforms to all relevant UK and European Standards
The Weed burner is designed for outdoor use, however it should always be stored
undercover and disconnected from the mains power when not in use or in the event
of wet weather.
The use of an RCD circuit breaker is recommended at all times whilst operating the
Weed Burner.
Always disconnect the Weed Burner from the Mains and allow to cool before
cleaning or storing.
Never leave the Weed burner unattended when in use.
Exercise due caution at all times if used in the vicinity of children and pets.
This appliance generates heat during use; do not touch hot surfaces during
operation.
Do not use with a programmer, timer or any other device that switches it on
automatically.
Imported By: TOOLTIME (UK), LTD G74 5HG
Please retain for future reference
Table des matières
