Vivotek MD8562 Manuel utilisateur
MD8562/8562D
P/N:625015501G Ver1.1
Copyright 2011 VIVOTEK INC. All rights reserved.
c
2MP .Vandal-proof .Mobile Surveillance
EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Contact your distributor in the event of
occurrence.
Refer to your user’s manual for
the operating temperature.
Warning Before Installation
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
EN - 2
Software CD
MD8562
Quick Installation Guide /
Warranty Card
Screwdriver
Alignment Sticker
Ground Wire / Screws
5
1
0
0
0
0
2
1
0
G
Package Contents
1
Moisture Absorber / RJ45 Female/
Female Coupler
(PoE) General I/O Terminal Block
(With power cord)
Ethernet 10/100 RJ45 Plug
Microphone In (pink)
Power Cord Socket (black)
MD8562D
EN - 3
English
IMPORTANT!
Record the MAC address before
installing the camera.
Screw Holes
Physical Description
2
Inner View
Outer View
Lens
MicroSD/SDHC
Card Slot
Waterproof Level: IP67
Reset button
Status LED
EN - 4
First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your
MicroSD/SDHC Card if necessary.
Then, follow the steps below to install the camera to either a ceiling or wall:
1. Attach the supplied alignment sticker to the ceiling/wall.
2. Using the 3 screw circles on the sticker, drill 3 pilot holes into the ceiling/wall. Then hammer the
plastic anchors into the holes if necessary.
3. This Network Camera can be mounted with the cable routed through the ceiling/wall or from the
side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown in the
picture. If the cable goes through the rear opening of the dome cover, please remove the plastic
cover (B).
4. Through the 3 holes on the camera base, insert the screws to corresponding holes and secure
the camera base with a screwdriver.
1
2
3
4
A
B
A
Dome Cover
Hardware Installation
3
Tamper-proof Screw
Camera Base
Plastic Cover
Ceiling Mount
EN - 5
English
1
2
B
A
3
4
Wall Mount
Installing the Ground Wire
As shown in the gure below, secure one side of the supplied ground wire to the screw hole, route
the wire, and attach the other end to a junction box or a grounded conduit.
IMPORTANT!
Please secure the screws tightly
to avoid moisture.
EN - 6
General Connection (without PoE) (MD8562D)
Network Deployment
4
+ : Digital input
- : Digital input
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
2
3
Ethernet Switch
1
1. If you have external DI devices, make the connection from general I/O terminal block.
2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch.
Use a Category 5 Cross Cable when Network Camera is directly connected to PC.
3. Connect the power cable from the Network Camera to a power outlet.
EN - 7
English
Power over Ethernet (PoE) (MD8562)
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
PoE Switch
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the camera to a PoE-enabled switch via
Ethernet cable.
POWER C
OLLIS
ION
LINK
RECEIVE
PARTITION
12345
PoE Power Injector
(optional)
Non-PoE Switch
NOTE:
1. This equipment is only to be connected to PoE networks
without routing to outside plants.
2. For PoE input connection, use only UL listed I.T.E. with
PoE output.
3. The DC power adaptor, if used, should comply with:
O/P: 12Vdc, 1.5A min., L.P.S. certied.
EN - 8
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is ana-
lyzed, please click on the “Next” button to continue the program.
0002D108323
00-02-D1-10-83-23 192.168.5.151 MD8562
Installation
Wizard 2
Assigning an IP Address
5
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras
on the same LAN.
4. After a brief search, the main installer window will pop up. Double-click on the MAC address
that matches the one printed on the camera label or the serial number on the package box
label to open a browser management session with the Network Camera.
EN - 9
English
For further setup, please refer to the user's manual on the software CD.
Ready to Use
6
To adjust the viewing angle
90°
1
2
Adjusting the Lens
7
Loosen the screws (not removing
them) on the sides of lens module.
Adjust the lens to a desired viewing
angle as shown on the right.
When done, fasten the screws so that
lens orientation can be xed
and withstand shock and
vibration.
1. A browser session with the Network Camera should prompt as shown below.
2. You should be able to see live video from your camera. You may also install the 32-channel
recording software from the software CD in a deployment consisting of multiple cameras.
For its installation details, please refer to its related documents.
Autres manuels pour MD8562
8
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Vivotek Caméra de sécurité
Vivotek
Vivotek IB8381 -E Manuel utilisateur
Vivotek
Vivotek IP139 Manuel utilisateur
Vivotek
Vivotek SD9365-EHL Manuel utilisateur
Vivotek
Vivotek WFD Manuel utilisateur
Vivotek
Vivotek Supreme SD8363E Manuel utilisateur
Vivotek
Vivotek IB8354-C Manuel utilisateur
Vivotek
Vivotek IP7161 Manuel utilisateur
Vivotek
Vivotek FD8179-H Manuel utilisateur
Vivotek
Vivotek FD8155H Manuel utilisateur
Vivotek
Vivotek IP8172 Manuel utilisateur
Vivotek
Vivotek IP7139 Manuel utilisateur
Vivotek
Vivotek FD7160 Manuel utilisateur
Vivotek
Vivotek 2M Manuel utilisateur
Vivotek
Vivotek IP7151 Manuel utilisateur
Vivotek
Vivotek IP9167-HP Manuel utilisateur
Vivotek
Vivotek Supreme IP8151 Manuel utilisateur
Vivotek
Vivotek FD8166 Manuel utilisateur
Vivotek
Vivotek FD816C-HF2 Manuel utilisateur
Vivotek
Vivotek IP8330 Manuel utilisateur
Vivotek
Vivotek FD8138-H Manuel utilisateur
