Vivotek IP8352 Manuel utilisateur
EN-1
English
Warning Before Installation
Contact your distributor in the
event of occurrence.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Do not touch the Network Camera
during a lightning storm.
Do not place the Network Camera on
unsteady surfaces.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
Replacing or failing to properly
install the waterproof components,
e.g., cables or cable glands, will void
our IP65/66/67 warranty.
EN-2
Package Contents
1
Software CD
IP8352
Quick Installation Guide /
Warranty Card
Waterproof Connector (Optional)
Alignment Sticker
Wall Mount Bracket
Sun Shield
Wrench / RJ45 Female/Female Coupler / Double-sided Tape / Screws
Power Adapter
Moisture Absorber
EN-3
English
Physical Description
2
IR LEDs
Lens
Light Sensor
General I/O
Terminal Block
SD/SDHC
Card Slot
Zoom Controller
Focus Controller
Reset Button
General I/O Terminal Block
Gb Ethernet
RJ45 Plug
Power Cord Socket
+ AC 24V +
- AC 24V -
EN-4
1
2
5
4
3
6
5
4
6
1. Attach the alignment sticker to the wall. Drill three holes into the wall. Then hammer the supplied
plastic anchors into the holes and secure the plate with supplied screws.
2. Feed the cables through the front opening of the wall mount bracket. (If you want to use external
devices such as sensors and alarms, please refer to the assembling steps on the next page.)
3. Hang the wall mount bracket on the plate.
4. Fix the Network Camera on the wall mount bracket with two screws on both sides.
5. Secure the wall mount bracket with the supplied screws.
6. Adjust the angle of the wall mount bracket to aim at the shooting area.
Hardware Installation
3
IMPORTANT:
The supplied L-type hex key wrenches are exclusively
designed to match each screw. In case you will need to adjust
the lens later, do not discard the wrenches.
EN-5
English
Waterproof Connector
1 Power +12V
2 Digital Output
3 Digital Input
4 Ground
5 RS485 +
6 RS485 -
7 Ground
8 Audio Input
9 Ground
10 Audio Output
87654321 109
1. Disassemble the components of the waterproof connector into part (A) ~ (F) as shown above.
2. Remove the rubber stopper from the bottom of the Network Camera and secure the rubber (A)
and screw nut (B) tightly.
3. Open the back cover of the Network Camera.
4. If you have external devices such as sensors and alarms, feed the cables through the waterproof
connector (F --> E --> C --> A+B) as the illustration shown below. Then refer to the pin denition
to connect them to the general I/O terminal block. Note: The recommended cable gauge is 2.0 ~ 2.8
mm.
5. Push the seal (C) into the housing (E).
6. Insert the seals (D) into the empty holes on the seal (C) to avoid moisture.
7. Secure the sealing nut (F) tightly.
8. Tighten the back cover.
9. Remove rubber (G) and feed the cables through the wall mount bracket.
Components of the Waterproof Connector
Seals (D)
Housing (E)
Sealing Nut (F)
Seal (C)
Screw Nut (B)
Pin Denition
Assembling Steps
Rubber (A)
(A)+(B)
2
6
(E)
(C)
(F)
(D)
(C)
4
7
(E)
(F)
3
(C)
5
8
9
(F)
(G)
EN-6
IMPORTANT:
Although the camera and the cable gland on the camera's end are waterproof, the cable
molding at the other end is not waterproof.
Measures should be taken to prevent water from leaking in through the cable-end
molding, such as the use of expanding foam sealant, putties, and so on. Note that the
cable gland on the camera should also be securely fastened to attain its waterproof
functionality.
Waterproof Not Waterproof
Cable Molding
EN-7
English
Network Deployment
4
Power over Ethernet (PoE)
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled
switch via Ethernet cable.
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
Non-PoE Switch
PoE Power Injector
(optional)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE Switch
RJ45 Female/
Female Coupler
RJ45 Female/
Female Coupler
EN-8
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
Network Camera
Model No: IP8352
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
MAC:0002D1730202
R o H S
0002D1730202
00-02-D1-73-02-02 192.168.5.151 IP8352
Installation
Wizard 2
IW
2
Assigning an IP Address
5
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After a brief search, the main installer window will pop up. Double-click on the MAC
address that matches the one printed on the camera label or the S/N number on the
package box label to open a browser management session with the Network Camera.
EN-9
English
For further setup, please refer to the user's manual on the software CD.
Ready to Use
6
3. Unscrew the zoom controller to adjust the
zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the
focus range. Upon completion, tighten the
focus controller.
T
W
∞
N
3
4
1. A browser session with the Network Camera should prompt as shown below.
2. You should be able to see live video from your camera. You may also install the
32-channel recording software from the software CD in a deployment consisting of
multiple cameras. For its installation details, please refer to its related documents.
Autres manuels pour IP8352
2
Table des matières
Autres manuels Vivotek Caméra de sécurité
Vivotek
Vivotek IB9365-EHT-A Manuel utilisateur
Vivotek
Vivotek AT-CAB Manuel utilisateur
Vivotek
Vivotek MD7530 Manuel utilisateur
Vivotek
Vivotek FE8181 Manuel utilisateur
Vivotek
Vivotek FD8361 Manuel utilisateur
Vivotek
Vivotek FE8173 Manuel utilisateur
Vivotek
Vivotek FD8166 Manuel utilisateur
Vivotek
Vivotek IB8377-H Manuel utilisateur
Vivotek
Vivotek IP8335H Manuel utilisateur
Vivotek
Vivotek SD8333-E Manuel utilisateur
Vivotek
Vivotek PZ8111 Manuel utilisateur
Vivotek
Vivotek TC5632 Manuel utilisateur
Vivotek
Vivotek IP8161 Manuel utilisateur
Vivotek
Vivotek FD8377-HTV Manuel utilisateur
Vivotek
Vivotek IP8330 Manuel utilisateur
Vivotek
Vivotek IP7135 Manuel utilisateur
Vivotek
Vivotek CaMate CM48 Series Manuel utilisateur
Vivotek
Vivotek PT3117 Manuel utilisateur
Vivotek
Vivotek CC8130 Manuel utilisateur
Vivotek
Vivotek FD8166 Manuel utilisateur
