Vista VK2-1080MD37PTW Manuel utilisateur
VK2-1080MD37PTW
Quick guide
2
Please read this manual thoroughly before use, and keep it handy for future reference.
3
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PROCUCT TO
RAIN OR MOISTURE. DO NOT INSERTANY METALLIC OBJECT THROUGH THE VENTILATION
GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of un-insulated "dangerous voltage" within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
PRECAUTIONS
Safety -------------------------------------- Installation -------------------------------
Should any liquid or solid object fall into the
cabinet, unplug the unit and have it checked by
the qualified personnel before operating it any
further.
Unplug the unit from the wall outlet if it is not
going to be used for several days or more. To
disconnect the cord, pull it out by the plug. Never
pull the cord itself.
Allow adequate air circulation to prevent internal
heat build-up. Do not place the unit on surfaces
(rugs, blankets, etc.) or near materials(curtains,
draperies) that may block the ventilation holes.
Do not install the unit in an extremely hot or
humid place or in a place subject to excessive
dust, mechanical vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Cleaning ---------------------------------
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use
strong solvents such as thinner or benzene as
they might damage the finish of the unit.
Retain the original carton and packing materials
for safe transport of this unit in the future.
4
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE
THE EQUIPMENT.
CE COMPLIANCE STATEMENT
WARNING: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
5
1. Description
This manual applies to the VK2-1080MD37PTW mini dome camera with Pan/Tilt function.
These cameras are fully featured for security surveillance and remote monitoring needs. They are
based on the DSP compression chip, allowing real-time, full frame rate Motion JPEG and H.264 (or
MPEG-4) video streams.
The camera can also connect wirelessly to the VK2-REC04HDW Wi-fi NVRs.
1.1 Components
The system comes with the following components:
Camera Unit Installation CD Installation Guide
Accessory Kit Template sheet
Note 1: Check your packaging to make sure that you received the complete system, including all
components shown above.
Note 2: Adapter for DC 12V is not supplied.
6
1.2 Layout
Connection Cable
Camera Dimension
See the diagrams below for the exact dimension
VK2-1080MD37PTW
Dimensions Unit: mm
NO
Wire Color
Description
1
Grey
Audio line output, RCA Jack
2
Red: DC12V
White: GND
Main Power, 2pin terminal
3
Blue: GND
Grey: ALARM INPUT
Brown: GND
Yellow : ALARM OUT
Alarm input and out put connections
4
Black
Ethernet, RJ-45 port compatible with 10/100Mbps having PoE
functionality.
7
2. Installation
• Camera Installation
Carefully remove the contents from the box, and verify that nothing was damaged in shipment.
1) Make screw holes for camera using the template sheet supplied
2) Remove the Camera Cover
3) Fix the camera using the anchors(2x) and screws(2x) provided.
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
cross-over cable is used for directly connection to PC, while a direct cable is used for connection
to a switch
Micro SD memory slot
Insert the SD memory card.
• Connecting the Power ( If not using PoE)
Connect the DC 12V power adaptor to the camera.
• Connecting the Wireless using WPS function.
Follow steps for a proper operation.
1. Make sure your AP (Access Point) and Operating System support WPS (Wi-Fi Protected Setup)
functions. WPS enables easy setup with compatible APs.
2. Press the WPS button on the camera board. You can then see the Status LED is blinking.
8
4. Press and hold down the WPS button on your AP (some router/AP will have a virtual button on
their management software instead). Refer to your AP's documentation for details using its WPS
functions
When WPS configuration is done, wireless connectivity will be established and the security
encryption, such as WEP or WPA-PSK, will be synchronized with the AP.
As for IP setting, the camera's use of DHCP or static IP is determined by your configuration on the
network camera via the web- based configuration of firmware. The camera's default is DHCP for
the VIP2P1N.
Notes:
1. WPS may not work if yourAP is configured with a "hidden" SSID.
2. If any WPS-enabled AP is not detected, the camera will search APs for 60 seconds after
pressing the WPS button, and if the camera still can not detect an AP after 1 minute, the
wireless setup will be cancelled.
3. If a camera is assigned with a fixed IP outside the AP's network segment, wireless setup will fail.
4. Awired connection always has a higher priority, and hence wireless setup will not take effect
when the RJ45 LAN port is connected.
9
2.2 Network Connection and IP assignment
The Network Camera supports the operation through the network. When a camera is first connected to
the network it has no IP address. So, it is necessary to allocate an IP address to the device with the
“Smart Manager” utility on the CD. (Default IP 192.168.30.220)
1. Connect the Network Camera / device to the network and power up.
2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager), the main window
will be displayed, after a short while any network devices connected to the network will be
displayed in the list.
3. Select the camera on the list and click right button of the mouse. You can see the pop-up menu
below.
4. Select Assign IP. You cam see a Assign IP window. Enter the required IP address.
Note: For more information, refer to the Smart Manger User’s Manual.
10
3. Operation
The Network Camera can be used with Windows operating system and browsers. The recommended
browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome with Windows.
Note:To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX
controls.
3.1 Access from a browser
1. Start a browser (Internet Explorer).
2. Enter the IP address or host name of the Network Camera in the Location/Address field of your
browser.
3. You can see a starting page. Click Live View or Setup to enter web page.
4. The network camera’s Live View page appears in your browser.
Table des matières
Autres manuels Vista Caméra IP
