VisionAIR VISION15 Manuel utilisateur
Note : Only use these function when
loading. For removal, press one or
three seconds depending on the
option selected and the star ✱will
disappear.
OR
INSTRUCTION BOOKLET
for programming calibration of the
VISION15 INTEGRATED SCALE
for 10-12 WHEEL TRUCKS
TOTAL
32,000 KG
Front: to select
Rear: to select
Distributions NJCO inc.
1036, Route de Fossambault
St-Augustin-de-Desmaures QC G3A 1W8
418 624-0884
www.balancevisionair.com | info@balancevisionair.com
LES BALANCES
1) DESCRIPTION OF THE RESET OPTION
• This function allows you to submit a load with the net weight (payload) only.
By activating this function, the balance displays zero kg or zero lbs.
• Enter the weights of the truck and semi-trailer loads separately.
• It is possible to install lights on the truck and semi-trailer to monitor the load from outside of
the truck (optional).
OTHER OPTIONS AVAILABLE ON THE VISION15 SYSTEM
Press the button for 3 seconds, select the ( ) buttons, follow the instructions on the
monitor or confirm with the button.
1) Empty programming: See pages 2 and 3 of this booklet; C
2) Full programming: See pages 2 and 3 of this booklet;
3) Pound or kilogram option;
4) Exterior lights option: See point 1 of this page;
5) VISION15 light option: Lights for loading directly on the display (total load);
6) Unit number option: To identify the truck no. and the no. of the wireless LiberT (optional);
7) Manual calibration;
8) Contrast;
9) Auto On-Off;
10) PSI DIsplay;
11) 10 or 100 kg/lb option: Displays every 10 or 100 kg or lbs.;
12) Language;
13) Password option: Blocks access to the system calibration;.
Programming procedure for exterior lights
Note - Net: maximum load weight (light will stay on).
Fast: weight at which the light will flash rapidly.
Slow: weight at which the light will flash slowly.
Identification
press
half-second
10 to 12 wheel
selection mode
Menu
Press 3 sec.
VISION15
Light
P : PSI Air pressure
Axial weight
Total weight
On / Off Press
3 sec.
Light mode and reset
Press 3 sec. and
a star will appear *
(See point 1page 4)*
Press for 3seconds
Select
Confirm
On/Off
Press
VISION15
light for a
half‑second
Loading mode
Correction of empty trck
weight. Press for 1 second
and a star will appear *
SLOW
SLOW
FAST
FAST
NET
NET
EXTERIOR LIGHT
Hold
to save
Hold
to save
CERTIFIED BALANCE
CERTIFIED BALANCE
Empty Truck
Empty Total
Other options available. See page 4.
CERTIFIED BALANCE
CERTIFIED BALANCE
EMPTY / FULL /
EMPTY / FULL /
FULL CALIBRATION PROCEDURE
STEP 4
Move the full front of the truck forward onto the certified scale and enter the weight.
FULL FRONT
Ex.: 12,000 kg
STEP 5
Move the entire full truck and forward onto the certified scale and enter the weight.
FULL TOTAL
Ex.: 32,000 kg
STEP 6
Full calibration programming mode with lifting axle on the ground (12 wheel truck).
Press to select.
This is where you enter the full weight of
the front of the truck. Press or for
the desired weight.
Once the correct weight is selected,
press to confirm.
This is where you enter the total weight
of the full truck. Press or to obtain
the desired weight.
Once the correct weight has been
selected, press the button for
3seconds to save.
NOTE 2 : For
good results,
ensure that all
operations are
completed on
a horizontal
surface.
NOTE 1 :
IMPORTANT
Always fill
up before
beginning
calibration.
EMPTY CALIBRATION PROCEDURE
STEP 1 See note 1and note 2on page 3.
Move the front of the empty truck forward onto the certified scale and enter the weight.
Empty front
Ex.: 5,000 kg
STEP 2
Move the empty tractor truck forward onto the certified scale and enter the weight.
Empty total
Ex.: 10,000 kg
STEP 3
Empty calibration programming mode with lifting axle on the ground (12 wheel truck).
Press to select.
This is where you enter the empty weight
of the front of the truck. Press or
for the desired weight.
Once the correct weight is selected,
press to confirm.
This is where the total weight of the
empty truck is to be maintained. Press
or to obtain the desired weight.
Once the correct weight has been
selected, press the button for 3
seconds to save.
FRONT
RETURN TO TOTAL
FRONT + REAR
CAL FULL
- +
- +
Hold for
3seconds.
FRONT
RETURN TO TOTAL
FRONT + REAR.
EMPTY CAL
- +
- +
Autres manuels VisionAIR Échelle
