Viper AS710R Manuel utilisateur

Electronic Service

Manuals

This electronic document is provided as a service to our customers.

Wedonotcreatethecontentsoftheinformationcontainedinthisdocu-

ment. Shouldyouhavedetailedquestionspertainingtotheinformation

contained in this document, you may contact Michco, or the manufac-

turer which provided the original information in this electronic deliver-

able. Michco’sonlypartin this electronic deliverable was the electronic

assemblyprocess. Byprovidingthismanualonlinewearenotguaran-

teeing parts availability.

You may contact Michco through the following methods:

Phone (517) 484-9312 or (800) 331-3339

2011 N. High St. -- Lansing, Michigan -- 48906

Fax: (517) 484-9836

Email: [email protected]

Web site: www.Michco.Com

Parts Web site: www.FloorMachineParts.Com

Order Parts on Line at:

www.FloorMachineParts.Com

Directly to Parts & Service:

By Email: [email protected]

By Fax: (517) 702-2041

By Voice: Use numbers above.

Serving the Cleaning Industry Since 1922

Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.

ManualsaresubjecttoManufacturer’sreproductionlimitations. Originalsorreproductionswereprovidedbymanufacturers

through a request. We make no warranty as to the correctness of information provided in this document and you assume

allrisk. By placing thesemanualsonlinewe are notdeclaringourcorporation to be anmanufacturerauthorizeddealer or

provider, please check ourwebsiteforauthorizedmanufacturerswerepresent.

Ride-on Scrubbers

USER MANUAL

READ USER MANUAL CAREFULLY BEFORE USE

Please fill out & return your warranty card

VR10029 REV.02

2016-1-13

Model #

Serial No.#

Machine destription

Machine structure

A1 --Seat (with Safety button)

A2 -- Recovery tank lid

A3 -- Recovery tank

A4 -- Solution tank

A5 -- Squeegee

A6 -- Adjust nut of brush skirt

A7 -- Brush skirt

A8 -- Brushes

A9 -- Drive motor

A10--Foot pedal of brush lift or low

A11--USB port for phone charging

A12--Front housing

A13--Control panel

A14--Steering wheel

A15--Emergency-stop button

A16--Net bag

B1 -- Squeegee pressure adjustment knob

B2 -- Squeegee fixing knob

B3 -- Vacuum hose inlet

B4 -- Rear squeegee latch

C1 -- Drain hose

C2 -- Recovery tank turn latch

C3 -- Charging cable storage

C4 -- Clean water inlet

C5 -- Squeegee lift lever

C6 -- Drive pedal

C7 -- Water level sight tube

C8 -- Batteries

D1 -- Drain cover

D2 -- Water valve

D3 -- Filter

E1 -- LED display

E2 -- Recovery tank full indicator

E3 -- The brush on/off button

E4 -- Drive motor indicator

E5 -- Key switch

E6 -- Speed potentiometer

E7 -- Forward/reverse button

E8 -- Clean water flow control button

E9 -- Horn

E10--Solution tank empty indicator

E11--Battery capacity indicator

F1 -- Charging port

F2 -- Charging LED indicator

F3 -- Circuit breaker

Figure A

Figure B

Figure C

Figure D

EFigure

Figure

USER MANUAL

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is constructed for use in an indoor environment

and is not intended for any other use. Use only with recommended accessories.

All operators shall read, understand and exercise the following safety precautions:

1) DO NOT OPERATE MACHINE:

 Unless trained and authorized.

 Unless you have read and understand the user manual.

 In flammable or explosive areas.

 If not in proper operating condition.

 In outdoor areas.

2) BEFORE OPERATING MACHINE:

 Make sure all safety devices are in place and operate properly.

3) WHEN USING MACHINE:

 Go slow on inclines and slippery surfaces.

 Follow all safety guidelines.

 Be very careful when using the machine in reverse.

 Report and repair any damage to machine prior to operating it.

4) BEFORE LEAVING OR SERVICING MACHINE:

 Never park the machine on a slope.

 Turn machine off.

5) WHEN SERVICING MACHINE:

 Read user manual thoroughly prior to operating or servicing this machine.

 Use manufacturer supplied or approved replacement parts.

 Use approved jack or hoist to safely elevate the machine.

 Disconnect batteries prior to working on machine.

 Wear gloves when handling batteries or battery cables.

 Avoid moving parts. Do not wear loose fitting clothing while servicing machine.

6）SAFETY DEVICES

 Emergency-stop button(A15)

When the Emergency-stop button is pressed, the machine will come to a sudden

stop, and all machine functions and displays will stop. Twist the button slightly to

reset it.

 Seat safety button (inside A1).

If the operator leaves the seat during operation, the drive motor will shut off in 0.5

seconds. The LED screen displays STOP.

USER MANUAL

WARNING Indicates a potential risk of injury or dangerous situation with risk of

death for the operator.

NOTED Indicates a remark related to important or useful functions.

MACHINE SET UP & INSTALLATION

UNPACKING MACHINE

Be sure and check packing carton for any damage. Report immediately any damage to carrier.

Check contents of package to ensure that the following items are included:

1, Machine

2, Squeegee assembly

3, Brush assembly(x2)

4, User manual

5, Battery charger (If equipped)

6, Batteries (x4) (If equipped)

7, Connecting wire for battery and charger (If equipped)

8, Warning lamp (If equipped)

9,Bumper bracket(If equipped)

BATTERY CONNECTIONS

1. Turn off the key switch (E5).

2. Flip the seat (A1) to the open position, use the latch (C2) and open the battery

compartment. If the machine does not include batteries, contact your distributor for

recommended batteries.

After selecting batteries, please choose WET or GEL mode with toggle switch on the back of

PCB, as shown in the figure below.

USER MANUAL

3. Carefully place the four batteries into the compartment as shown in figure below. Place the

battery brace at the front of the four batteries.

4. Connect battery cables to posts in numbered order as shown in the figure below.

5. Apply a coat or protective spray on the cable connections to prevent battery corrosion.

6. Cover recovery tank and seat.

Make sure the recovery tank is empty when opening it.

Do not drop batteries into compartment. Do not put metal on the batteries.

Never connect + to +, or - to - , never connect + to – with single battery, when

disassembling or installing the batteries.

MACHINE SET UP

PRE-OPERATION CHECKS

1. Sweep or dust mop the surface to be cleaned.

2. Check battery meter to make sure batteries are fully charged. (see BATTERY CHARGING)

3. Check that brush / pad is properly installed.

4. Check that squeegee is properly installed.

5. Check the speed driver (A9) is work normally.

6. Make sure the recovery tank is empty. If not, drain it.

7. Make sure solution tank water indicator (E10) is not on. If on, fill water in solution tank (A4).

8. Check that the water valve (D2) is not indicated “0”.

INSTALLING PAD DRIVER OR BRUSH

1. Ensure that the machine is turned off (E5).

2. Raise the brush head (A7) off the floor by depressing the front of foot pedal (A10) on the left

of machine.

3. Put brushes (A8) below both brush driver motor hub.

4. Lower the brush deck (A7) by depressing the rear of foot pedal (A10). While sitting on the

machine, turn on the brush switch (E3) insure the speed control knob (E4) is set to minimum.

Lightly depress driver pedal (C6), and the brush motors will turn on. The brushes should

attach to the machine automatically.

USER MANUAL

5. Adjust the nut (A6) to properly position the splash guards.

Never work without the brusher/pad perfectly installed.

When cleaning or replacing the brushes, you should raise the brush head and rotate

the reverse direction to “working” direction quickly. The two brushes are reverse in

direction.

INSTALLING AND ADJUSTING THE SQUEEGEE

1. Ensure that the machine is turned off (E5).

2. Turn the squeegee lift lever (C5) to put down the squeegee bracket (A5) on floor.

3. Loosen the two knobs (B2) on the squeegee and slide the squeegee into the slots in the back

of the squeegee bracket.

4. Tighten the knobs(B2) securely.

5. Secure the vacuum hose (B3) on the pick-up tube of the squeegee.

6. Adjusting the nut (B1) to properly set the squeegee angle.

FILLING THE SOLUTION TANK

1. The solution fill hose is under the seat(C4).

2. Do not overfill the solution tank. Leave at least two inch from the opening of tank.

3. Water temperature should not exceed 40°C/104°F.

Use only low-foam and non-flammable detergents suitable for ride-on scrubber

applications.

Each time that you need to fill the solution tank, always empty and clean the recovery

tank by removing the drain hose plug (C1). After each use, unscrew the drain cap (D1) to

drain solution tank.

CHECKING THE SPEED DRIVER

1. Sit on seat (A1) of the machine.

2. Turn on the key switch (E5).

Depress the front,

Brushes up

Depress the rear,

Brushes down

Autres manuels pour AS710R

Table des matières

Autres manuels Viper Scrubber

Viper

Viper DR 1500 H Manuel utilisateur

Viper

Viper FANG 20T Manuel utilisateur

Viper

Viper FANG 20 Manuel utilisateur

Viper

Viper FANG 20HD-EU Manuel utilisateur

Viper

Viper AS430C Manuel utilisateur

Viper

Viper AS5160 Manuel utilisateur

Viper

Viper AS5160 Guide de l'utilisateur

Viper

Viper AS380/15B-AU Manuel utilisateur

Viper

Viper FANG 20HD-EU Manuel utilisateur

Viper

Viper AS380/15B-EU Manuel utilisateur

Viper

Viper AS5160 Manuel utilisateur

Viper

Viper AS710R Manuel utilisateur

Viper

Viper AS430C Manuel utilisateur

Viper

Viper FANG 32T-EU Manuel utilisateur

Viper

Viper AS4325B Mode d’emploi

Viper

Viper Fang 32T Manuel utilisateur

Viper

Viper VE13P Manuel utilisateur

Viper

Viper AS6690T Manuel utilisateur

Viper

Viper AS510B Manuel utilisateur

Viper

Viper AS430B Manuel utilisateur

Viper

Viper AS1050R Guide de l'utilisateur

Viper

Viper AS430B Manuel utilisateur

Viper

Viper AS380/15B-EU Manuel utilisateur

Viper

Viper AS430C Manuel utilisateur

Manuels Scrubber populaires d'autres marques

Olympus

Olympus M200H Manuel utilisateur

Clarke

Clarke BEXT 100H Manuel d'installation et d'exploitation

JOHNY VAC

JOHNY VAC JVC70BCT Manuel utilisateur

RCm

RCm Elan Series Manuel

Kärcher

Kärcher B 120 W Manuel utilisateur

Truvox

Truvox Orbis MotorScrubber 20 Manuel utilisateur

Numatic

Numatic TTB 4045/100 Manuel utilisateur

U.S. Products

U.S. Products PEX 500-C-TICK Mode d'emploi

Mclennan

Mclennan C510 Manuel utilisateur

Tennant

Tennant T20 LPG Manuel utilisateur

Columbus

Columbus ARA 66 BM 100 Manuel utilisateur

Numatic

Numatic TTV 678G / 300T Manuel utilisateur

American-Lincoln

American-Lincoln 505-945 Manuel utilisateur

FIORENTINI

FIORENTINI ET 65-75 Manuel utilisateur

Floorpul

Floorpul ruby 48 blt Guide de l'utilisateur

Onyx

Onyx RX-34 Manuel utilisateur

Dustbane

Dustbane Hurricane 400 Manuel utilisateur

Sana

Sana EUJ-702 Manuel utilisateur