Viking 56798 Instructions de montage
CHARGE
COMPLETELY
IMMEDIATELY
AFTER PURCHASE.
Fully recharge
after each use.
Fully recharge every
3 months to ensure
long battery life.
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
CHARGE
COMPLETELY
IMMEDIATELY
AFTER PURCHASE.
Fully recharge
after each use.
Fully recharge every
3 months to ensure
long battery life.
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back
of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep
this manual and the receipt in a safe and dry place for future reference. 20g
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2019 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
To ols required for assembly and se rv ic e m ay n ot b e i nc lu de d .
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item 56798
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Symbol Property or Statement
VVolts
~Alternating Current
AAmperes
CCA Cold Cranking Amps
RC Reserve Capacity
mAh Milliampere-hours
WARNING marking concerning
Risk of Eye Injury.
Wear ANSI-approved
eye protection.
Read the manual before
setup and/or use.
WARNING marking
concerning Risk of Fire.
Follow connection procedure.
WARNING marking concerning
Risk of Explosion.
Page 3For technical questions, please call 1-888-866-5797.Item 56798
INSTRUCTIONS PERTAINING TO RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
When using this product, basic precautions should
always be followed, including the following:
1. Read all the instructions
before using the product.
2. To reduce the risk of injury, close
supervision is necessary when the
product is used near children.
3. Do not put fingers or hands
into the product.
4. Use of an attachment not recommended
or sold by power pack manufacturer
may result in a risk of fire,
electric shock, or injury to persons.
5. To reduce risk of damage to the
electric plug and cord, pull the
plug rather than the cord when
disconnecting the power pack.
6. Do not use a battery pack or appliance
that is damaged or modified.
Damaged or modified batteries may
exhibit unpredictable behavior resulting
in fire, explosion or risk of injury.
7. Do not operate the power pack
with a damaged cord or plug,
or a damaged output cable.
8. Do not disassemble the power pack,
take it to a qualified service person
when service or repair is required.
Incorrect reassembly may result in
a risk of fire or electric shock.
9. To reduce the risk of electric shock,
unplug the power pack from
the outlet before attempting
any instructed servicing.
10. WARNING – RISK OF
EXPLOSIVE GASES.
a. WORKING IN VICINITY OF A LEAD
ACID BATTERY IS DANGEROUS.
BATTERIES GENERATE
EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION.
FOR THIS REASON, IT IS OF
THE UTMOST IMPORTANCE
THAT YOU FOLLOW THE
INSTRUCTIONS EACH TIME
YOU USE THE POWER PACK.
b. To reduce risk of battery explosion,
follow these instructions and those
published by battery manufacturer
and manufacturer of any equipment
you intend to use in vicinity of the
battery. Review cautionary marking
on these products and on engine.
11. PERSONAL PRECAUTIONS
a. Consider having someone close
enough by to come to your aid when
you work near a lead-acid battery.
b. Have plenty of fresh water and
soap nearby in case battery acid
contacts skin, clothing, or eyes.
c. Wear complete eye protection and
clothing protection. Avoid touching
eyes while working near battery.
Page 4 For technical questions, please call 1-888-866-5797. Item 56798
d. If battery acid contacts skin
or clothing, wash immediately
with soap and water. If acid
enters eye, immediately flood
eye with running cold water
for at least 10 minutes and get
medical attention immediately.
e. NEVER smoke or allow a spark or
flame in vicinity of battery or engine.
f. Be extra cautious to reduce risk
of dropping a metal tool onto
battery. It might spark or short-
circuit battery or other electrical
part that may cause explosion.
g. Remove personal metal items such
as rings, bracelets, necklaces, and
watches when working with a lead-
acid battery. A lead-acid battery can
produce a short-circuit current high
enough to weld a ring or the like
to metal, causing a severe burn.
12. When charging the internal battery,
work in a well ventilated area and do
not restrict ventilation in any way.
13. Under abusive conditions, liquid
may be ejected from the battery;
avoid contact. If contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
14. Do not expose a power pack to
fire or excessive temperature.
Exposure to fire or temperature
above 265°F may cause explosion.
15. Have servicing performed by a qualified
repair person using only identical
replacement parts. This will ensure that
the safety of the product is maintained.
16. Attach output cables to a battery and
chassis as indicated below. Never allow
the output clamps to touch one another.
a. Use the Power Pack for jump-
starting a LEAD-ACID battery only.
b. For emergency use only.
Do not use the Power Pack as a
replacement for a vehicle battery.
c. Be sure area around battery
is well ventilated while battery
is being jump-started.
d. NEVER jump-start a frozen battery.
e. Do not attempt to jump-start a
vehicle with a non-rechargeable
or defective battery.
f. Study all battery manufacturer’s
specific precautions for
jump-starting.
g. DO NOT TOUCH POSITIVE
AND NEGATIVE BATTERY
CLAMPS TOGETHER.
h. Unplug the Power Pack from
its Adapter before connecting
its cables to a battery.
i. Connect and disconnect
battery cable clamps only
after setting any Power Pack
switches to OFF position.
j. Connect cables to proper
polarities. Connect red cable
to positive battery terminal and
black cable to vehicle chassis.
k. Locate Power Pack as far away
from battery as battery cables permit.
17. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
18. Store idle equipment. Always lock up
tools and keep out of reach of children.
19. Do not operate if Power Pack has
received a sharp blow, been dropped,
or otherwise damaged in any way;
take it to a qualified technician.
20. Do not leave Power Pack unattended
while switched on. It could result
in fire and property damage.
21. Do not expose to rain or wet conditions.
Water entering the Power Pack will
increase the risk of electric shock.
Page 5For technical questions, please call 1-888-866-5797.Item 56798
22. Do not use an extension
cord with this item.
23. Wear ANSI-approved splash-
resistant safety goggles
and heavy-duty rubber work
gloves whenever
connecting,
disconnecting, or working near battery.
Battery acid can cause
permanent blindness. Avoid touching
eyes while working near battery.
24. Do not use Power Pack while you
are tired or under the influence
of drugs, alcohol or medication.
A moment of inattention while
operating Power Pack may result
in serious personal injury.
25. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference
or pacemaker failure.
26. Maintain labels and nameplates.
These carry important safety
information. If unreadable or
missing, contact Harbor Freight
Tools for a replacement.
27. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and
caution are factors which cannot
be built into this product, but must
be supplied by the operator.
SAVE THESE INSTRUCTIONS.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should
malfunction or breakdown, grounding
provides a path of least resistance for
electric current to reduce the risk of electric
shock. This product is equipped with a cord
having an equipment grounding conductor
and a grounding plug. The plug must be
plugged into an outlet that is properly
installed and grounded in accordance
with all local codes ordinances.
WARNING – Improper connection of
the equipment grounding conductor is
able to result in a risk of electric shock.
Check with a qualified electrician if you
are in doubt as to whether the product
is properly grounded. Do not modify the
plug provided with the product – if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
Specifications
Starting Current 221 A
Peak Current 450 A
Battery Lithium Iron Phosphate 12,000 mAh
12 VDC Power Output 6 A
USB Output 5 VDC, 2 A
LED Flashlight 3 W / 250 Lumens
Page 6 For technical questions, please call 1-888-866-5797. Item 56798
Setup - Before Use
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.
Components and Controls
Battery
Clamp Cable
USB Cable120 VAC Adapter
12 VDC Adapter
12 V Port Adapter
Main Power Button
Flashlight
Button
Engine Start
Socket
Starter Button
Starter Ready
Light
Charging
Input Socket
Warning Light
USB
Output Port
~
12 VDC
Output Port
Charge Indicator Lights
Page 7For technical questions, please call 1-888-866-5797.Item 56798
Charging the Power Pack
WARNING! TO PREVENT SERIOUS
INJURY: Only use the Chargers included
with the Power Pack. Use of any
other charger will damage the unit.
Always charge on a non-flammable surface
in a well-ventilated area. Do not use the
Power Pack while it is being charged.
Note: Before initial use, completely
charge the Power Pack.
1. To check the battery power level, press
and hold the Main Power Button about
one second to turn on the Power Pack.
2. Power level is indicated by four
blue indicator lights on the Control
Panel marked 25%, 50%, 75%, and
100%. If all four blue indicator lights
are lit, the battery is fully charged.
3. Recharge: a. When power level on
Control Panel reads less than 100%.
b. After each use. c. At least once
every 3 months when not in use.
NOTE: FAILURE TO RECHARGE POWER
PACK WILL VOID WARRANTY.
120 VAC Charging
1. Plug the 120 VAC Adapter into
a 2- or 3-prong outlet.
2. Insert the Adapter’s charging connector
into the Charging Input Socket on
the side of the Power Pack.
3. The blue indicator light on the Control
Panel for the power level being
charged will flash while charging,
then stay lit when complete while the
next higher level blue indicator light
flashes while charging, and so on.
4. When the unit is fully charged all four
blue indicator lights will remain lit.
Approximate AC Charge Time
3 hours
Figure A
5. When charging is complete unplug the
120 VAC Adapter from its outlet and
disconnect it from the Power Pack.
12 VDC Charging
1. To charge the Power Pack from
a vehicle’s 12 VDC power supply,
plug the 12 VDC Adapter into
the vehicle’s 12 VDC outlet.
2. Plug the other end of Adapter
into the Charging Input Socket on
the side of the Power Pack.
3. Start the vehicle’s engine to allow its
alternator to charge the Power Pack.
Note: The vehicle’s battery alone will
NOT charge the Power Pack—the
vehicle’s engine needs to run.
WARNING! TO PREVENT
SERIOUS INJURY: Vehicle must
be outdoors to prevent build up of
deadly, odorless exhaust gases.
4. The blue indicator light on the Control
Panel for the power level being
charged will flash while charging,
then stay lit when complete while the
next higher level blue indicator light
flashes while charging, and so on.
When the unit is fully charged all four
blue indicator lights will remain lit.
Approximate DC Charge Time
4 – 6 hours
Figure B
5. When charging is complete
unplug the 12 VDC Adapter from
the vehicle’s 12 VDC outlet and
disconnect it from the Power Pack.
Page 8 For technical questions, please call 1-888-866-5797. Item 56798
Operating Instructions
Using the LED Flashlight
1. Press and hold the Main Power
Button about one second to turn on
the Power Pack. The blue indicator
lights on the Control Panel will
illuminate, indicating the unit is on.
2. To turn the Flashlight on, press
the Flashlight Button.
3. For an SOS signal, press the
Flashlight Button again.
4. For a flashing light, press the
Flashlight Button again.
5. To turn the Flashlight off, press
the Flashlight Button again.
Note: Flashlight will shut off
automatically after 30 minutes.
Jump-Starting a Vehicle
Note: Read the vehicle owner’s
manual pertaining to jump-starting
prior to using the Power Pack.
NOTICE: To avoid damage to the vehicle’s
electrical system, do not use the Power Pack
on a vehicle that has no battery installed.
1. Verify that the Power Pack is fully
charged and recharge as needed,
following the instructions in Charging
the Power Pack on page 7.
2. Turn off the vehicle ignition
switch and all accessories (lights,
radio, climate control, etc.).
3. Plug the Battery Clamp Cable
into the Engine Start Socket on
the side of the Power Pack.
WARNING! TO PREVENT
SERIOUS INJURY: DO NOT
TOUCH POSITIVE AND NEGATIVE
BATTERY CLAMPS TOGETHER.
4. Connect the red Positive Battery Clamp
to vehicle’s positive battery terminal.
Then connect the black Negative
Battery Clamp to the vehicle chassis.
WARNING! TO PREVENT SERIOUS
INJURY: DO NOT CONNECT TO THE
NEGATIVE TERMINAL OF THE BATTERY.
5. When the correct connection has been
made, press and hold the Main Power
Button about one second to turn on
the Power Pack. Press and hold the
Starter Button about one second until
the green light comes on indicating
unit is ready to jump-start vehicle.
WARNING! TO PREVENT SERIOUS
INJURY: RISK OF EXPLOSION.
If the Battery Clamps are connected
incorrectly, a beep will sound and the red
warning light on the Control Panel will light.
Press and hold the Main Power Button
to turn off the unit. Correct the
connections and repeat step 5.
6. Attempt to start the vehicle. If the
vehicle does not start after 5 to 8
seconds, stop and wait at least
1 minute before trying again.
7. After the vehicle is started, press and
hold the Main Power Button about one
second until the green indicator light
goes out to turn off the unit. Remove
the black Negative Battery Clamp first,
and then the red Positive Battery Clamp.
8. Recharge the Power Pack.
Note: Jumpstart mode lasts for only one
minute. After one minute, unit will shut
down. Follow Step 5 to re-power unit.
Page 9For technical questions, please call 1-888-866-5797.Item 56798
Running/Charging DC Appliances
1. Verify Power Pack is fully charged and
recharge as needed. Refer to Charging
the Power Pack on page 7.
2. Make sure that the appliance to be
powered is turned off and its power
requirement does not exceed 6 A.
3. Plug the 12 V Port Adapter into
the 12 VDC Output Port on the
side of the Power Pack.
4. Plug the appliance into the
12 V Port Adapter.
5. Turn on the appliance.
6. When finished using, turn off
and unplug the appliance.
7. Recharge the Power Pack.
Running/Charging USB Devices
1. Verify Power Pack is fully charged and
recharge as needed. Refer to Charging
the Power Pack on page 7.
2. Plug the supplied USB Cable (or the
device USB cable) into the USB Output
Port on the side of the Power Pack.
3. Plug the appropriate connector on
the USB Cable into the device.
4. Press and hold the Main Power Button
about one second to turn on the Power
Pack. Turn device on, if necessary.
5. When finished using, unplug the
device from the USB Cable.
6. Recharge the Power Pack.
Page 10 For technical questions, please call 1-888-866-5797. Item 56798
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn Power Switch to its “off” position, unplug the Power Pack, and allow it to cool
completely before performing any inspection, maintenance, or cleaning procedures.
1. BEFORE EACH USE, inspect
the general condition of the
Power Pack. Check for:
• loose hardware
• cracked or broken parts
• damaged electrical wiring
or cable insulation
• any other condition that may
affect its safe operation.
2. Keep unit clean and clamps free
of dirt, debris, or grease.
3. Li-Ion BATTERY MUST BE RECYCLED
OR DISPOSED OF PROPERLY.
Do not short, incinerate or open battery.
4. AFTER USE, wipe external surfaces
of the Power Pack, Battery Clamps,
and cords with clean cloth. Do not use
flammable liquids or harsh detergents
to clean the Power Pack.
5. Power Pack contains no user-
serviceable parts. Service
must be performed only by
a qualified technician.
6. Fully charge battery and store
the Power Pack and Accessories
in the Carrying Case out of
the reach of children.
Troubleshooting
Problem Possible Causes Likely Solutions
Red warning light comes
on and unit beeps.
Battery Clamps are
connected backwards
(reverse polarity) or
there is a short circuit.
Turn Power Pack off and correct
Clamp connections. Turn unit
back on and resume operation.
Unit beeps. 1. Overload on 12 VDC
output port.
2. Overload on USB
output port.
1. Turn unit off and check that
electronic device being powered
does not exceed 6 A load limit.
2. Turn unit off and check that
electronic device being powered
does not exceed 2 A load limit.
Red warning light
comes on.
Power Pack battery
is overheated.
Wait five minutes for battery to
cool, then resume operation.
Red warning light flashes. Battery Clamp Cable
malfunction.
Repair or replace Battery
Clamp Cable.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Table des matières
Autres manuels Viking Bloc d'alimentation
