ViewSonic PJ-vTouch-10S Manuel utilisateur
PJ-vTouch-10S
Projector Interactive Kits
User Guide
Model No. VS16519
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specic languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Thank you for choosing ViewSonic
As a world leading provider of visual solutions, ViewSonic is dedicated to
exceeding the world’s expectations for technological evolution, innovation,
and simplicity. At ViewSonic, we believe that our products have the
potential to make a positive impact in the world, and we are confident that
the ViewSonic product you have chosen will serve you well.
Once again, thank you for choosing ViewSonic !
i
Compliance Information
Please read before proceeding
• Use only the batteries and power adapter provided by the manufacturer. The use
of unauthorized accessories may void your warranty.
• Do not store your device in temperatures higher than 50°C (122°F).
• The operating temperature for this device is from 0°C (32°F) to 35°C (95°F).
FCC Notice
The following statement applies to all products that have received FCC approval.
Applicable products bear the FCC logo, and/or an FCC ID in the format FCC ID:
GSS-VS15180 on the product label.This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation. This
mobiledevice has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequencyenergy
and, if not installed and used in accordance with the instructions, may cause
harmful interferenceto radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void theuser’s authority to operate the equipment.The antenna(s)
used for this transmitter must not be colocated or operating in conjunction with any
otherantenna or transmitter.
The device was tested and complies to measurement standards and procedures
specified in FCC OET Bulletin 65, Supplement C
ii
FCC SAR Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions
for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
The users manual or instruction manual for an intentional or unintentional radiator
shall caution the user that changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate the
equipment.
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU, R&TTE Directive 1999/5/EC.
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment as
unsorted municipal waste, but use the return and collection systems
according to local law.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery has
a heavy metal content of more than 0.0005% Mercury, or more than 0.002%
Cadmium, or more than 0.004% Lead.
European Union Regulatory Conformance
The equipment complies with the RF Exposure Requirement 1999/519/EC, Council
Recommendation of 12 July 1999 on the limitation of exposure of the general
public to electromagnetic fields (0-300 GHz). This equipment meets the following
conformance standards: EN301489-1, EN301489-17, EN55022/24, EN60950-1,
EN300328, EN301893.
We, hereby, declare that this Wi-Fi radio is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
iii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum
Concentration Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
iv
Copyright Information
Copyright © ViewSonic®Corporation, 2017. All rights reserved.
ViewSonic®, the three birds logo, OnView®, ViewMatch™, and ViewMeter®are
registered trademarks of ViewSonic®Corporation.
Disclaimer: ViewSonic®Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic®Corporation reserves
the right to change product specifications without notice. Information in this
document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic®Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it
becomes available, please register your product on the Internet at: www.viewsonic.
com.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
PJ-vTouch-10S
Wireless Presentation Gateway
VS16519
PJ-vTouch-10S_UG_ENG Rev. 1C 04-17-17
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
v
Contents
Compliance Information
Please read before proceeding ..............................................................................i
FCC Notice.............................................................................................................i
FCC SAR Information............................................................................................ii
CE Conformity for European Countries.................................................................ii
Following information is only for EU-member states: ............................................ii
European Union Regulatory Conformance............................................................ii
Declaration of RoHS2 Compliance....................................................................... iii
Copyright Information
Product Registration.............................................................................................iv
For Your Records .................................................................................................iv
Packaged Items
Part names of the supplied stylus pen...................................................................2
Charging Stylus .....................................................................................................2
Notes for using Stylus............................................................................................2
Setup Procedure
Setup Flow.............................................................................................................3
Operating Environment / EyeRIS
Supported OSs are as follows...............................................................................7
About trademarks ..................................................................................................7
Setup Procedure....................................................................................................7
Install the Software onto the Computer .................................................................7
How to uninstall the software...............................................................................10
Startup the Software............................................................................................11
Calibration Menu Display.....................................................................................12
Performing Calibration.........................................................................................13
Perform Calibration Automatically [Automatic Calibration]..................................14
Perform Calibration Manually [Manual Calibration] ............................................15
vi
Troubleshooting
The stylus pen does not work..............................................................................18
The finger touch operation does not work ...........................................................18
Lines traced with the stylus pen do not match screen.........................................18
You can check the installation condition of the camera unit when the
troubleshooting in the EyeRIS setup menu is displayed on ................................19
Windows Operating System Version...................................................................20
Specifications
Customer Support
1
Packaged Items
Make sure your box contains everything listed. If any pieces are missing, contact
your dealer.
• Camera unit x 1
• Laser Module unit x1
• Adapter
• Quick start Guidel x 1
• Screw (T3 x 15) x 2
• Stylus pen x 2
• USB cable x 1 (For charging the stylus pen)
• Mini USB cable (5 m) x 1 (For connecting the computer with the camera unit)
• Y Cabel
• Sync Cabel
• Installation disc
• 3M double-sided molding tape
Notes:
• Download the driver and the calibration software from our website to install them
on the computer. URL:
• Drawing software is required to use the interactive white board function.
Get commercially available drawing software.
2
Part names of the supplied stylus pen
Tip LED indicator
Charging jack (Mini USB)
Charging Stylus
Please use the Stylus charging cable and connect the charging jack of Stylus to
a USB port on a computer and Stylus will start charging; it takes approximately 3
minutes to charge Stylus.
• Press the tip of Stylus and the LED indicator will turn red. This means that Stylus
charging is completed. When the LED indicator on Stylus does not light up,
please follow the steps described above to charge Stylus again.
Notes for using Stylus
• Please do not use Stylus improperly, including dropping, banging or
disassembling Stylus.
• If Stylus comes in contact with water or any other type of liquid, please wipe it dry
immediately and keep it dry.
• Avoid high temperature and humidity.
Table des matières
Autres manuels ViewSonic Accessoires pour projecteur
ViewSonic
ViewSonic PJ-PEN-003 Manuel utilisateur
ViewSonic
ViewSonic WMK-005 Manuel utilisateur
ViewSonic
ViewSonic ViewBoard VB-WPS-001 Manuel utilisateur
ViewSonic
ViewSonic PJ-CART-001 Manuel utilisateur
ViewSonic
ViewSonic myViewBoard Direct Manuel utilisateur
ViewSonic
ViewSonic myViewBoard Box Manuel utilisateur
ViewSonic
ViewSonic AutoProject Key WPG-400 Manuel utilisateur
