ViewSonic PD1611 Manuel utilisateur
PD1611
Pen Display
User Guide
Model No. VS16164
IMPORTANT: Please read this User Guide to obtain important information
on installing and using your product in a safe manner, as well as
registering your product for future service. Warranty information contained
in this User Guide will describe your limited coverage from ViewSonic
Corporation, which is also found on our web site at http://www.viewsonic.
com in English, or in specic languages using the Regional selection box
in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Thank you for choosing ViewSonic
With over 25 years as a world leading provider of visual solutions,
ViewSonic is dedicated to exceeding the world’s expectations
for technological evolution, innovation, and simplicity. At
ViewSonic, we believe that our products have the potential to
make a positive impact in the world, and we are condent that
the ViewSonic product you have chosen will serve you well.
Once again, thank you for choosing ViewSonic !
i
For U.S.A.
This device complies with part 15 of FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radi-
ate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
yConsult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly
approved by the party responsible for compliance could void your authority
to operate the equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
Compliance Information
ii
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC
and Low Voltage Directive 2006/95/EC.
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electri-
cal and Electronic Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment as
unsorted municipal waste, but use the return and collection systems
according to local law.
If the batteries, accumulators and button cells included with this
equipment, display the chemical symbol Hg, Cd, or Pb, then it means
that the battery has a heavy metal content of more than 0.0005%
Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.
iii
Important Safety Instructions
1. DO NOT place objects on top of the device, as objects may scratch the
screen.
2. DO NOT expose the device to dirty or dusty environments.
3. DO NOT place the device on an uneven or unstable surface.
4. DO NOT insert any foreign objects into the device.
5. DO NOT expose the device to strong magnetic or electrical eld.
6. DO NOT expose the device to direct sunlight as it can damage the LCD
Screen. Keep it away from heat sources.
7. DO NOT use the device in the rain.
8. Please check with your Local Authority or retailer for proper disposal of
electronic products.
9. The device may produce some heat during normal operation or
charging. To prevent discomfort or injury from heat exposure, DO NOT
leave the device on your lap.
10.POWER INPUT RATING: Refer to the rating label on the device. Only
use accessories specied by the manufacturer.
11.DO NOT use any sharp object to tap the screen.
12.Clean the touch screen with a soft cloth. If needed, dampen the cloth
slightly before cleaning. Never use abrasives or cleaning solutions.
13.Disconnect the device from an electrical outlet and power off before
cleaning the device.
14.DO NOT disassemble the device. Only a certied service technician
should perform repair.
15.Users have to use the connection to USB interfaces with USB 2.0
version or higher.
iv
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with
Directive 2011/65/EU of the European Parliament and the Council on
restriction of the use of certain hazardous substances in electrical and
electronic equipment (RoHS2 Directive) and is deemed to comply with
the maximum concentration values issued by the European Technical
Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum
Concentration
Actual
Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers
(PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the
Annex III of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode uorescent lamps and external electrode
uorescent lamps (CCFL and EEFL) for special purposes not exceeding
(per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per
lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by
weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys
containing 85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or
ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic
devices, or in a glass or ceramic matrix compound.
v
Copyright Information
Copyright © ViewSonic®Corporation, 2016. All rights reserved.
ViewSonic and the three birds logo are registered trademarks of ViewSonic
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or edito-
rial errors or omissions contained herein; nor for incidental or consequential
damages resulting from furnishing this material, or the performance or use of
this product.
In the interest of continuing product improvement, ViewSonic Corporation
reserves the right to change product specications without notice. Informa-
tion in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any
means, for any purpose without prior written permission from ViewSonic
Corporation.
Product Registration
To meet your future needs, and to receive any additional product informa-
tion as it becomes available, please register your product on the Internet at:
www.viewsonic.com.
For Your Records
Product Name: PD1611
ViewSonic Pen Display
Model Number: VS16164
Document Number: PD1611_UG_ENG Rev. 1B 02-24-17
Serial Number: ____________________________________
Purchase Date: ____________________________________
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living
green. Thank you for being part of Smarter, Greener Computing. Please visit
ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
vi
Contents
Compliance Information.............................................................i
Important Safety Instructions................................................... iii
Declaration of RoHS2 Compliance..........................................iv
Copyright Information ...............................................................v
Product Registration.................................................................v
1. Introduction.......................................................................... 1
1.1 Packing list ...................................................................................... 1
1.2 Product overview............................................................................. 1
2. Installation and Setting ........................................................ 3
2.1 Install driver ..................................................................................... 3
2.2 Set the display area......................................................................... 5
2.3 Handwriting area correspondence .................................................. 6
2.4 More touch settings ......................................................................... 7
3. Troubleshooting................................................................... 9
3.1 Screen problems ............................................................................. 9
3.2 Problems of interactive electromagnetic pen ................................ 10
4. Product Specication..........................................................11
4.1 Screen ........................................................................................... 11
4.2 Interactive electromagnetic pen ................................................... 12
5. Appendix............................................................................ 13
5.1 Replace the pen tip ....................................................................... 13
Customer Support ................................................................. 14
Limited Warranty ................................................................... 15
1
1. Introduction
1.1 Packing list
After unpacking, please conrm whether the following contents are included:
Electromagnetic pen display
Electromagnetic pen display support
Power adapter
USB 2.0 Y cable
Electromagnetic pen
Pen rope
Pen tip x 3
Pen tip replacement tool
Quick Start Guide
Driver and instructions disk
Warranty card (only Chinese zone)
For any part aws or defects, please consult the original product dealer.
1.2 Product overview
1.2.1 Front view and side view
①Display and electromagnetic pen touch area
②Pen holder
③Power button
④ Brightness adjustment button (turn up)
⑤ Brightness adjustment button (turn down)
⑥Ergonomic support
2
1.2.2 Rear view
⑦Pen slot
⑧Pen rope hole (×2)
⑨Lock hole (×2)
⑩USB output interface
11 Power interface
Note: please don't open the enclosure, which exists electric shock hazard.
Please contact with the service personnel for any problem.
1.2.3 Interactive electromagnetic pen
The interactive electromagnetic pen is made with electromagnetic
resonance technology and does not require batteries.
Table des matières
Autres manuels ViewSonic Moniteur
ViewSonic
ViewSonic VS17351 Manuel utilisateur
ViewSonic
ViewSonic CDE4200-L Manuel utilisateur
ViewSonic
ViewSonic VS13533 Manuel utilisateur
ViewSonic
ViewSonic VA2432-H-W Manuel utilisateur
ViewSonic
ViewSonic VS11605 Manuel utilisateur
ViewSonic
ViewSonic VS17380 Manuel utilisateur
ViewSonic
ViewSonic VP2775 Manuel utilisateur
ViewSonic
ViewSonic TD2210 Manuel utilisateur
ViewSonic
ViewSonic VX2450w-LED Manuel utilisateur
ViewSonic
ViewSonic VTA700 Manuel utilisateur
ViewSonic
ViewSonic G71 Manuel utilisateur
ViewSonic
ViewSonic VS18697 Manuel utilisateur
ViewSonic
ViewSonic VA2736-MH Manuel utilisateur
ViewSonic
ViewSonic GS790 - 19" CRT Display Manuel utilisateur
ViewSonic
ViewSonic VA1912WB - 19" LCD Monitor Manuel utilisateur
ViewSonic
ViewSonic E55-2 Manuel utilisateur
ViewSonic
ViewSonic VS12844 Manuel utilisateur
ViewSonic
ViewSonic VX2428J Manuel utilisateur
ViewSonic
ViewSonic VG2448 Manuel utilisateur
ViewSonic
ViewSonic E96FSB Manuel utilisateur
