Videosystems WB-8412SD Manuel utilisateur
1/33
User Manual
4 Ch Video Sever
2/33
WARINGS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
DO NOT INSERT ANY METALLIC & ELETRIC CONDUCTIVE OBJECT THROUGH
VENTILATION GRILLS.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION：TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
COPYRIGHT
THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED
TO THEIR RESPECTIVE COMPANIES.
3/33
Content
I. PREFACE.....................................................................................................................................................4
II. PRODUCT SPECIFICATIONS.................................................................................................................4
III. PRODUCT INSTALLATION.....................................................................................................................6
A. MONITOR SETTING.....................................................................................................................................6
B. HARDWARE INSTALLATION ........................................................................................................................7
C. IPASSIGNMENT .........................................................................................................................................8
D. INSTALLACTIVEXCONTROL (SETUP ONCE ONLY):...................................................................................12
IV. LIVE VIDEO..............................................................................................................................................14
V. VIDEO SERVER CONFIGURATION....................................................................................................16
A. SYSTEM ...................................................................................................................................................17
B. NETWORK................................................................................................................................................20
C. MULTIMEDIA............................................................................................................................................26
D. EVENT......................................................................................................................................................30
VI. FACTORY DEFAULT...............................................................................................................................33
VII. PACKAGE CONTENTS...........................................................................................................................33
4/33
I. PREFACE
This is a four channel MPEG-4/MJPEG Video Server with web server built-in.
It encodes analogue signals of traditional cameras to digital signals; the users can
monitor real-time video via IE browser. MPEG-4 compression format supports
smooth video quality. Also, it supports USB backup. 2-way audio enables the user
to have a video conference. In addition, the user can control Video Server with
user friendly interface via IE browser to build a home surveillance system.
II.Product Specifications
Features:
zMPEG-4/MJPEG compression formats
zRS-485 Control Interface (PTZ)
zSD Card backup.
zWireless network connection (802.11 b/ g) - Optional
z2-way audio.
zSupport Cell Phone/PDA
zOnline firmware upgrade.
zSupport dynamic IP and PPPoE through free DDNS.
zSupport AVI video backup via IE browser.
zCompatible with Microsoft Windows Media Player.
5/33
Hardware
CPU ARM 9 ,32 bit RISC
RAM 64MB
ROM 8MB
Video Input BNC x 4
Input Video Looping BNC x 4
Audio In/Out 1 in / 1 out (RCA type)
Alarm Input X4
Relay Out X1
RS-485 X1, for PTZ control
Power Lan: DC 12V 600mA / WLAN: DC 12V 700mA
Dimensions (WxHxD) 218x44x202mm
Network
Ethernet 10/ 100 Base-T
Wireless 802.11b/g
WEP 64/ 128 bit
Network Protocol HTTP, TCP/ IP, SMTP, FTP, PPPoE, DHCP, DDNS, NTP
System
Video Resolution NTSC: 668x448, 336x224, 160x96
PAL: 688x544, 336x272, 160x128
Video adjust Brightness, Contrast, Saturation, Hue
Image snapshot Yes
Full screen monitoring Yes
Compression format MPEG-4,JPEG
Video bitrate adjust CBR, VBR
Motion Detection 1 Areas per 1 channel
Triggered action Relay, Mail, FTP, Save to USB storage
Post alarm Yes
Security Password protection
Firmware upgrade HTTP mode, can be upgraded remotely
Simultaneous connection Up to 20
Audio Yes, 2-way (Duplex Support)
USB Storage
Recording trigger Motion Detection, Alarm, IP check, Network Status (wire
connection only)
Video format AVI, JPEG
6/33
Delete files Yes, can be deleted or overwrite
Client system requirement
OS Windows 2000, XP, 2003
IE IE 6.0 or above
Hardware (Minimum) Intel-C1.6G, RAM: 256MB, Graphic Card: 32MB
III. Product Installation
A. Monitor Setting
i. Right-Click on the desktop. Select “ Properties”.
ii. Change color quality to highest (32bit).
7/33
B. Hardware Installation
i. Connect power adaptor
ii. Connect Ethernet cable to Video Server
iii. Connect Video Server to a computer or Local network.
Ｂ-1 I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering, alarm notifications. It provides the interface to:
1 Digital Input (GND+Alarm) – An alarm input for connecting devices that can toggle
between an open and closed circuit, for example: PIRs, door/window contacts, glass
break detectors, etc. When a signal is received the state changes and the input becomes
active.
1 Relay output (COM +N.O. / COM + N.C.) – An output to Relay switch, for example:
LEDs,Sirens,etc
Digital Input
Alarm Input
1. GND (Ground) : Initial state is LOW
2. Alarm : Max. 50mA, 12VDC
Relay Output
1. COM: (Common)
2. N.O. (Normally Open) / N.C. (Normally Close): Max. 1A, 24VDC or 0.5A,
125VAC
B-2 Relay Connection:
Digital Input connection
GND
ALARM
COM
N.O./N.C.
ALARM IN
Relay Out
8/33
Relay Output Connection
C. IP Assignment
i. Use “IP Installer”, comes with CD, to assign the IP address of VIDEO
SERVER.
ii. There are two languages for IP Installer：
a. IPInstallerCht.exe: Chinese version
b. IPInstallerEng.exe: English version
iii. 3 different IP configurations based on different environments.
a. Fixed IP (Public IP or Virtual IP)
GND
ALARM
COM
N.O./ N.C.
GND
ALARM
COM
N.O./ N.C.
Door/Window
Contacts
9/33
b. DHCP (Dynamic IP)
c. Dial-up (PPPoE)
iv. Execute IP Installer
v. Use Windows XP SP2 or newer version. If the following message popup,
please click “Unblock.”
vi. The GUI of IP Installer：
vii. IP Installer searches all IP deceives which connect with the internet and
it lists all of them on the left side or the user can click “Search Device” to
search again.
viii. When the user clicks on each IP device listed on the left side of IP
Installer, the network configuration of the IP device will show on the right
side. The user can change the parameter and click on “Submit”. And,
then, the following message will popup. Click on “OK” to reboot VIDEO
SERVER.
10/33
ix. Please make sure the subnet of PC IP address and VIDEO SERVER IP
address are the same.
The same Subnet:
VIDEO SERVER IP address: 192.168.1.210
PC IP address: 192.168.1.100
Different Subnets:
VIDEO SERVER IP address: 192.168.2.210
PC IP address: 192.168.1.100
Table des matières
