Victron energy CCGX Manuel utilisateur
2020-11-11 18:41 1/8 GX - Generator auto start/stop
Victron Energy - https://www.victronenergy.com/live/
Generator auto start/stop on CCGX and
Venus GX
Introduction
An internal relay on the CCGX/Venus GX can be used to automatically start and stop a generator. This
relay - or switch - can be 'tripped' by a number of user-defined conditions. This manual will explain
what conditions are available to you; and it will guide you through the steps required to set-up this
useful functionality.
Firstly, wire the relay to a genset. The relay is located on the back of the CCGX - marked Relay. If
using a Venus GX, two relays will be seen at the bottom of the unit - only Relay 1 can be used for the
generator automatic start/stop functionality.
Wiring between the CCGX/Venus GX needs to be 'permanent' in order for the generator to keep
running; and also to allow automatic 'Stop' when the parameters for auto-stop have been met.
Besides driving the internal relay, the auto start/stop functionality can be also enabled to directly
control supported Fischer Panda generators. For more information on how to connect Fischer Panda
generators, see GX - Fischer Panda generators.
Enabling the start/stop function
Go to: Setttings → Relay and set the Function options to “Generator start/stop”
Relay
Now that has been enabled, all the settings pertaining to the Automatic Generator Start/Stop function
will be found in the main Menu under: Settings → Generator start and stop.
Fischer Panda
Last update: 2018-03-21 12:57 ccgx:generator_start_stop https://www.victronenergy.com/live/ccgx:generator_start_stop?rev=1521633420
https://www.victronenergy.com/live/ Printed on 2020-11-11 18:41
Enable the “AutoStart” function in the Fischer Panda generator control panel.1.
Go to the Fischer Panda genset page and set the Mode setting to “Auto start/stop”2.
Once the Mode is set, all settings will become available under the Auto start/stop menu entry at the
bottom of the page.
Main page
Generator state: Condition that is currently keeping the generator running.
Error: Error description.
Runtime: Generator runtime since last start.
Total run time: Accumulated running time since the first start.
Time to next test run: When the test run condition is enabled this item shows the time
remaining to the next test run.
Daily runtime: Page with the running times of last 30 days.
Settings: Generator start and stop settings menu.
Settings
2020-11-11 18:41 3/8 GX - Generator auto start/stop
Victron Energy - https://www.victronenergy.com/live/
Conditions: See Conditions
Minimum runtime: Once started the generator should run for a minimum amount of time, for
manual start this setting is ignored.
Detect generator at AC input: After starting the generator, it monitors the Multi (or Quattro),
to see if it connects to the generator. In case it does not it will cause an alarm. This function
catches a wide array of possible problems, like a simple no fuel situation, but also a tripped fuse
or other problem between the generator and the Quattro. This functionality is not available for
VE.Can connected Multi/Quattro.
Quiet hours: See Quiet hours
Reset daily run time counters: Reset the last 30 days run time counters.
Generator total run time: Sets the total run time counter.
Conditions
Conditions location: Generator start and stop → Settings → Conditions
* Battery monitor: Select which battery monitor will be used for DC related conditions.
* On loss of communication: Defines the behavior when the datalink between the CCGX/Venus GX
and the selected battery monitor and/or vebus inverter/charger is lost. Options are:
Stop the generator: If the generator is running and the datalink is lost, the generator will be
Last update: 2018-03-21 12:57 ccgx:generator_start_stop https://www.victronenergy.com/live/ccgx:generator_start_stop?rev=1521633420
https://www.victronenergy.com/live/ Printed on 2020-11-11 18:41
stopped. (default)
Start the generator: If the datalink is lost and one or more conditions depends on it the
generator will be started.
Keep running: If the generator was already running before the datalink loss this setting will
keep it running, but will not start it if was not running previously.
* Do not run genset when AC 1 is in use: It is intended for backup systems, with a Quattro, having
mains on AC in 1, and Genset on AC in 2. When this option is enabled, the Genset will only be started
after a mains failure. And in case of a mains failure, the Genset will automatically be stopped again as
soon as the mains is restored. This functionality is not available for VE.Can connected Quattros.
The following conditions are available to auto start/stop a generator:
Manual
State of charge (SOC)
AC load*
Battery current
Battery voltage
Inverter high temperature
Inverter overload
Periodic test run
* The measured value is the system total AC consumption.
Conditions are evaluated in the order shown above and when multiple conditions are reached only the
top one will be shown as active condition. All enabled conditions are evaluated even if the generator
is already started so when the active conditions ends, the next reached condition will keep the
generator running.
Condition settings
Use “condition” value to start/stop: Enables or disables the condition
Start when “condition” is higher/lower* than: When the value set here is reached, the
relay is closed to start the generator.
Start value during quiet hours: The same that above but when the “Quiet hours” mode is
active.
Start after the condition is reached for: Some values like AC load can vary suddenly due to
2020-11-11 18:41 5/8 GX - Generator auto start/stop
Victron Energy - https://www.victronenergy.com/live/
a consumption peak and go back to a normal value in a few seconds. In this kind of situations
the start of the generator is usually not desired. This option will delay the generator start until
the start value is reached for a minimum amount time.
Stop when “condition” is higher than: The same than above but for stop value.
Stop value during quiet hours: The same than above but for stop value.
Stop after the condition is reached for: The same than above but for stop value.
* Higher/lower value depends on the type of condition.
AC load condition
AC load condition works like the rest of conditions but has the “Measurement” extra setting.
The “Measurement” setting is available on firmware v2.0 and onwards and has three possible values:
Total consumption (Default option)
Inverter total AC out
Inverter AC out highest phase
Test run condition
Allows you to program a periodical test run.
Test run interval: Test run will be performed periodically based on this setting
Skip test run if has been running for: The test will be skipped if during the test run interval
the generator was running at least the number of hours set on this setting.
Last update: 2018-03-21 12:57 ccgx:generator_start_stop https://www.victronenergy.com/live/ccgx:generator_start_stop?rev=1521633420
https://www.victronenergy.com/live/ Printed on 2020-11-11 18:41
Test interval start date: The interval count will start based on this date, this setting can be
set in the future and the interval will be ignored till the set date is reached.
Start time: Time of day in which the generator will start
Test duration: Duration of the test
Run until battery is fully charged: Stops the generator after the battery is fully charged
instead of a fixed amount of time
Manual start
Use the manual start to directly start the generator. If the generator is already running you can use
this option to make sure that the generator won't stop automatically when the active condition
becomes inactive.
There are two ways to start the generator manually:
Using menu: Go to Generator start and stop → Manual start and use the switch to start the
generator.
Using generator page: Press the top-left button to show the generator page. Once in the
generator page press the center button, when pressed you will be asked how to stop the
generator, manually or using a timer. Once selected the stop mode a countdown of five seconds
will start, you can abort the manual start by pressing the center button.
2020-11-11 18:41 7/8 GX - Generator auto start/stop
Victron Energy - https://www.victronenergy.com/live/
WARNING: If the generator is manually started without a stop timer, won't stop until the user set to
off the manual start option.
In both options the use of a stop timer is available, use the timer to program the generator stop.
Manually stop the generator is only possible if no other condition is active. In the case that you want
to force the stop you should disable the active condition or disable the generator start and stop
function.
Quiet hours
Quiet hours allows you to set a time zone for nighttime with values that make the generator start only
when is really necessary.
When the “Quiet hours” mode is active, the conditions will use the related start/stop values.
To enable it go to the settings menu and set the “Enable quiet hours” switch on. Once enabled start
and end time settings will become visible.
You can make the “Quiet hours” mode to be permanently active(when enabled) setting both start and
stop time to the same value.
Using "Quiet hours" to define two time zones
Besides the main purpose of the “Quiet hours” mode you can also use it to define two time zones over
the day.
Examples of the use of different time zones:
Solar system: A cloudy morning may cause the generator to start by a low SOC condition, then
Last update: 2018-03-21 12:57 ccgx:generator_start_stop https://www.victronenergy.com/live/ccgx:generator_start_stop?rev=1521633420
https://www.victronenergy.com/live/ Printed on 2020-11-11 18:41
two hours after the clouds go away. In this case your batteries are charged and your solar
system wasting free energy. To avoid this situation you can set a time zone for daytime with a
lower start value for the SOC condition.
Away mode: Some holiday houses are only inhabited on weekends during which power
consumption is larger and the generator has to take care of keep batteries in good condfition.
The rest of the week the battery SOC level can be lower waiting to be charged by solar energy.
With time zones you can set a secondary time zone for the whole day and only enable/disable it
when the house is uninhabited.
Troubleshooting
Fischer Panda: Generator does not start and "Remote switch control
disabled" error is shown
Enable the “AutoStart” function in the Fischer Panda control panel.
Fischer Panda: Auto start/stop function stopped working after an error
Make sure that the issue is solved and clear the error to make the auto start/stop function work again.
DISQUS
View the discussion thread.
From:
https://www.victronenergy.com/live/ - Victron Energy
Permanent link:
https://www.victronenergy.com/live/ccgx:generator_start_stop?rev=1521633420
Last update: 2018-03-21 12:57
Autres manuels pour CCGX
9
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Victron energy Contrôleurs
Victron energy
Victron energy BlueSolar MPPT 75/10 Manuel utilisateur
Victron energy
Victron energy Lynx Smart BMS Manuel utilisateur
Victron energy
Victron energy BlueSolar PWM 12V 24V 5A Manuel utilisateur
Victron energy
Victron energy Digital Multi Control 200/200A Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 150/45-MC4 Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 75/10 Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 150/35 Manuel utilisateur
Victron energy
Victron energy VBC-HV Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 100/50 Manuel utilisateur
Victron energy
Victron energy BlueSolar PWM-Light 12/24-5 Manuel utilisateur
Victron energy
Victron energy NV-48030 Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 100/30 Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 150/85 Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 150/60-MC4 Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 75/10 Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 150/60-Tr Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 150/70 Manuel utilisateur
Victron energy
Victron energy BlueSolar MPPT 75/10 Manuel utilisateur
Victron energy
Victron energy SmartSolar MPPT 150/35 Manuel utilisateur
Victron energy
Victron energy MultiPlus-II 48/3000/35-32 230V GX Manuel utilisateur
