Viatom Visual Oxy Manuel utilisateur
Visual Oxy
Wrist Pulse Oximeter
User Manual
English|Deutsche|Italiano|Español|Français
Contents
User Manual…….…...........…..English 1-13
Benutzerhandbuch...........…...Deutsch 14-26
Manuale d'uso........…..…....…Italiano 27-39
Manual de usuario………….....Español 40-52
Manuel de l'utilisateu........…..Français 53-65
1
User Manual
User’s Manual
Contents
1. Introduction..................................................................2
2 Using the Monitor......................................................... 5
3 PC software (Optional).................................................. 9
4 Maintenance................................................................10
5 Troubleshooting...........................................................10
6 Specifications...............................................................11
7 Electromagnetic Compatibility....................................12
2
1. Introduction
1.1 Intended Use
This product is intended to be used for measuring,
displaying and storing of pulse oxygen saturation
(SpO2)，pulse rate and motion in home or healthcare
facilities environment. App can show real-time SpO2,
pulse rate; get record, display results and report.
Note:
The data and results provided by this device are for pre-check
screening purpose only and cannot be directly used for diagnostic
or treatment.
The data provided by the APP and PC software (optional) is not
intended for diagnosis or treatment purpose, always consult your
doctor for any health condition.
Warnings and Cautionary Advices
DO NOT squeeze the sensor or apply excessive force on
the sensor & cable.
Do not use this device during MRI examination.
Never submerge the device in water or other liquids. Do
not clean the device with acetone or other volatile solutions.
Do not place this device in pressure vessels or gas
sterilization device.
Consult your doctor immediately if you experience
symptoms that could indicate acute disease.
Do not self-diagnose or self-medicate on the basis of this
device without consulting your doctor. In particular, do not
start taking any new medication or change the type and/or
dosage of any existing medication without prior approval.
Use only cables, sensors and other accessories specified
3
in this manual.
Prolonged continuous SpO2monitoring may increase the
risk of undesirable changes in skin characteristics, such as
irritation, reddening, blistering or burns.
Check the SpO2sensor application site every 6-8 hours to
determine the positioning of the sensor and the circulation
and skin sensitivity of the patient. Patient sensitivity varies
depending on medical status or skin condition. For patients
with poor peripheral blood circulation or sensitive skin,
inspect the sensor site more frequently.
Functional tester cannot be used to assess the accuracy of
a SpO2sensor or a device.
This device is designed to determine the arterial oxygen
saturation percentage of functional hemoglobin. Factors
that may degrade pulse oximeter performance or affect the
accuracy of the measurement include the following:
- excess ambient light
- excessive motion
- electrosurgical interference
- blood flow restrictors
(arterial catheters, blood pressure cuffs, infusion lines,
etc.)
- moisture in the sensor
- improperly applied sensor
- incorrect sensor type
- poor pulse quality
- venous pulsations
- anemia or low hemoglobin -concentrations
- cardiogreen and other -intravascular dyes
- carboxyhemoglobin
- methemoglobin
- dysfunctional hemoglobin
4
1.2 Guide to Symbols
1.3 Unpacking
Main Unit × 1
Ring Sensor × 1
Cable × 1
User Manual × 1
Symbol
Description
Type BF-Applied Part
Manufacturer
European authorized representative
CE0197
CE Marking indicating conformance to
EC directive No. 93/42/EEC concerning
medical devices.
MRI unsafe. Presents hazards in all MR
environments as device contains
strongly ferromagnetic materials.
Indicate separate collection for electrical
and electronic equipment (WEEE).
IP22
Protected against spraying water and
against access to hazardous parts with a
tool, per IEC 60529.
Follow Instructions for Use.
Warning and Caution!
SN
Serial number
No alarm system.
5
2 Using the Monitor
2.1 Charging
Charge the battery before using.
Use the charge cable to charge the battery of device in
the USB Port of the computer or with USB charging
adapter.
After being fully charged, the device will power off
automatically.
2.2 POWER ON/OFF
POWER ON:
Press the button for 1 second to turn on the device.
POWER OFF:
Automatically power off: The device will turn off
automatically in 2 minutes if no measurement, no
operation or without App connection.
Manually power off: You can press the button for about
2 seconds to turn off.
2.3 TAKE THE FIRST RECORDING
START. Wear the device and the Ring Sensor, press
the button to power on. And keep
yourself in the quiet environment.
(For the sake of clarity, recommendelly
the user wear the Checkme 02 watch
on their left wrist and put the ring
sensor on the thumb. If it is too tight, try another
finger. Avoid being loose.)
STOP. After the record, take off the Ring Sensor (and
the device), the recording will be save
after the countdown. (If the working
time is less than 1 minute, the data
6
will not be saved.)
Note:
The device can also work as a clock and pedometer
without ring sensor, and the steps will restart counting
after the ring sensor plugged in.
Please avoid excessive motion for the sensed finger
during recording and avoid any strong ambient light
condition.
We recommend using the classic monitor mode in daily
environments and the sleep mode when you want to
sleep.
2.4 Stop monitoring & sync data
Take off the sensor, the countdown will
begin.
During the countdown, if you wear the sensor again, the
record will be resumed.
After the countdown, the data will be ready for sync.
Note:
1. The duration of the recording is 1mins~10 hours.
And the device can Collect and store maximum 4
recording, when the 5th recording coming, the first
recording will be will covered.
Sync data to the ViHealth App
You can Sync the data to your app after
the countdown or next time after you
turn on the device.
Note: Refer the ViHealth app manual for more details.
2.4.1 How to find the Serial Number？
1）Detach the the main unit from wristband.
7
2）Flip the main unit over, the series number is
printed on the label of product.
Note:
The SN Serial number is on the back of the device
2.5 How to synchronize the time of the device
The time of the Checkme 02 will be automatically
synchronized with the network time on your smart
device after connected with the app.
Note: Refer the ViHealth app manual for more details.
2.6 Operation Mode Navigation
The device has two operation modes: Sleep Mode
and Monitor Mode.
Turn on the device, during the icon blinking, press the
button to switch between two modes.
Sleep Mode
Monitor Mode
Parameters
SpO2, PR, Motion
SpO2, PR, Steps
Screen
Activated by button
Always on
The Sensor
Vibrates
When SpO2is
lower than
threshold set
When SpO2is lower
than threshold set；
Or when step goal is
met
Bluetooth
On when the
screen lights up
Always on
Report
Sleep report
Monitor report
8
2.7 Smart Vibration
The vibrator in the ring sensor will be activated when
the SpO2fall below the preset value (Threshold). The
vibration will stop when the SpO2recover to normal
level or you can press the button to stop it.
You can customize the vibration to help you sleep better
via app or PC(Only for the Checkme 02 Pro).
2.8 Download App
App name: ViHealth
iOS: App Store
Android: Google Play
Compatibility
The device is compatible with iOS versions 9.0+ and
Android versions 5.0+. Refer the ViHealth app manual
for more details.
2.9 Bluetooth Connection
The device Bluetooth will be enabled automatically only
when the screen lights up.
Note: when the Checkme O2 is pairing with the smart
device, keep the screen lights up.
Note: DO NOT PAIR in the settings of your smart
device.
2.10 Display
Time, Remaining battery capacity
Sleep Mode
Monitor Mode
MODE
MODE
18:45
Z
Z
M
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels Viatom Équipement médical
Viatom
Viatom Checkme Pro Manuel utilisateur
Viatom
Viatom Checkme Pro Manuel utilisateur
Viatom
Viatom Wellue Manuel utilisateur
Viatom
Viatom Checkme Pro Manuel utilisateur
Viatom
Viatom PO2 Manuel utilisateur
Viatom
Viatom FS10C Manuel utilisateur
Viatom
Viatom Checkme O2 Manuel utilisateur
Viatom
Viatom OxySmart PC-60FW Manuel utilisateur
Viatom
Viatom Checkme Lite Manuel utilisateur
Viatom
Viatom Checkme O2 Manuel utilisateur
Viatom
Viatom PB-20 Manuel utilisateur
Viatom
Viatom ER1 Manuel utilisateur
Viatom
Viatom Wellue WearO2 Manuel utilisateur
Viatom
Viatom BabyO2 Manuel utilisateur
Viatom
Viatom ER2 Manuel utilisateur
Viatom
Viatom OxySmart PC-60F Manuel utilisateur
Viatom
Viatom Checkme O2 Manuel utilisateur
Viatom
Viatom Wellue POD-2 Manuel utilisateur
