Vestfrost VTS254 Manuel utilisateur

Service Manual - Low Temperatur

VTS254 VTS256 VTS 258

Contents

Battery backup system ...........................2

Operation and function - Display ............3

Installing a remote alam .......................13

Replacement of door ............................15

Replacement of door gasket.................16

Replacement of door handle. ...............19

Replacement of wheels. .......................20

Replacement of closing bush ...............21

Replacement of LED light.....................22

Replacement of fan. .............................24

Replacement of Display........................26

Replacement of door hinge .................28

Replacement of controller.....................28

Recharching refrigerant VTS 254.........29

Recharching refrigerant VTS 256.........30

Recharching refrigerant VTS 258.........31

List of parameters VTS 254..................32

List of parameters VTS 256..................36

List of parameters VTS 258..................36

Plate with electrical parts......................38

Electrial Diagram.. ................................39

1. Open the door

2. Use a pen to switch on the battery backup

system in the hole

3. When turned on the switch it will have a

yellow light

NOTE!

The battery backup system does not supply

the cooling system with power to run.

When starting up the appliance for the rst

time it is necessary to switch on the battery

backup system.

Battery backup system

How to switch on the battery backup system:

Battery backup system

Some models are equipped with a battery backup system. The system supplies the controller

and keyboard with power at power failure. This makes it possible to supervise the tempera-

tures in the unit during the power failure.

The battery backup system makes it possible to supervise the temperatures for 50 hours.

After a power failure and at the rst start up the battery needs to be recharged. To regain the

full capacity the battery will be reloading for 10 days

NOTE!

The battery for backup should be changed

every third year to secure 50 hours of back

up. Please put this change in the mainte-

nance schedule for every third year.

Operation and function - Display

Start up:

When the appliance is connected to the power supply, the keyboard will automatically start up.

The start up view on the keyboard will show the di󰀨erent software installed on the controller of

the appliance.

Press enter to return from the start up view.

Operation – main view:

(1) The temperature in the appliance (measured by the TR3 probe)

(2) Time and date

(3) ALARM icon. Flashing by alarm. On when there has been an alarm, but the alarm is no

longer active.

(4) Logging icon. Of if no logging. On when logging

(5) Memory icon. On when the memory is 90% full. Flashing when the memory is full, and the

controller is deleting the oldest logging data.

(6) Memory bar. Shows the status of the memory.

Operation and function - Display

Keys – main view:

SET: Enter the Set Point menu of the temperature

SERVICE: Enter the Service menu

DATA: Enter the Data Logging menu

ALARM: Enter the Alarm menu

How to see and modify the temperature Set Point:

1. Push and immediately release the SET key: the display will show the Set Point value.

2. To modify the value push the SET key, the Set Point start ashing.

3. Use the UP and DOWN keys to modify the value.

4. To memorize the new Set Point value push the SET key again or wait 30sec.

Service menu:

From the main view push the SERVICE key and the SERVICE menu is entered.

See below picture:

PROBES: Enter the probes, to see the measured temperatures. 1-4 probes is availa

ble depending on model.

PARAMETERS: Enter the setting of the parameters. Please note that changes made to the

parameters should only be made of a technician. The code to enter the Pr2

parameters is standard set to 12.

See list of parameters in page 26-29

SELF TEST: Enter the Self Test program of the controller.

CLOCK: Enter clock menu, where it is possible to change date and time.

PASSWORD: Enter the password menu, where it is possible to change the password.

LANGUAGE: Enter the language menu, where it is possible to change language.

How to change parameter:

See the parameter list at page 26-29

1. Enter the SERVICE menu

2. Select PARAMETERS sub-menu

3. Push the ENTER key

4. Select Pr1 or Pr2 sub-menu. (Pr2 require a code to enter. The code is standard set to 12).

By Pr2:

A: Push the SET key

B: Set the password/code by means of the UP and DOWN keys

C: Push the SET key

D: Push the ENTER key

5. The parameter is divided into groups. Select the group using the UP and DOWN keys

6. Select the group by pushing the ENTER key

7. Select the parameter using the UP and DOWN keys.

8. When located on the value of the parameter push the SET key

9. Set the parameter by means of the UP and DOWN keys

10. Push the SET key, to conrm and pass to the next parameter

How to use the Self Test:

1. Enter the SERVICE menu

2. Select SELF TEST sub-menu

3. Push the ENTER key,

4. If PASSWORD is required, insert the password,

5. OTHERWISE the SELF TEST menu is entered directly.

6. Push the START key

7. Then push the keys to activate the correspondent loads:

a. Compressor

b. Light

c. Fan

d. Alarm

e. Buzzer

8. The display shows the status of the digital input (ON or OFF)

9. Wait 30s or push the BACK key to come back to the previous screen.

How to change language:

1. Enter the SERVICE menu

2. Select LANGUAGE sub-menu

3. Push the ENTER key and the LANGUAGE menu is entered.

4. Push the SET key and then use the UP and DOWN keys to select the language and then

the SET key to conrm it.

How to set time and date:

1. Enter the SERVICE menu

2. Select CLOCK sub-menu

3. Push the ENTER key.

4. Set the day by means of the UP and DOWN keys.

5. Push the SET key, to conrm and pass to the setting of time.

6. Use the same procedure as for the date.

7. Then conrm the selection by means of the SET key.

Data menu:

From the main view push the DATA key and the DATA menu is entered.

See below picture:

LOG: Enter the data logged by the controller.

EXPORT: Export the data to an USB pen drive delivered with the appliance.

GRAPH: Enter the graph showing the temperature logged the last 24h (with a logging inter-

val of 15min.)

How to enter the log:

1. Enter the DATA menu

2. Select LOG sub-menu

3. Push the ENTER key and the LOG menu is entered.

4. By UP and DOWN keys chose the data interval to display

5. Push the ENTER key to display the selected data.

NOTE: THE KEY: IS USED TO STOP AND START LOGGING

Logged data will have this layout:

Where TR3, EVP, TL1, TL2 = Value of probes.

With probe failure or absence:” - “ symbol is displayed. Please note that 1-4 probes are avai-

lable depending on model.

ST: status of the controller/load

●- = operating, without any load activated;

●D = defrost running (if automatic defrost is available)

●C = compressor working

How to export data:

1. Enter the EXPORT menu

2. Insert the USB pen drive supplied by Vestfrost.

3. Select ALARM or DATA, the controller starts sending data to the pen drive, when

the export is nished the message: EXPORT - Copy completed is displayed.

The exported data will be exported as a CSV-le (Comma Separated Values). This le can be

used in ex. Excel for making graphs.

IMPORTANT: during the download don’t remove the USB pen drive: this action could

damage the data les and USB pen drive itself.

WARNING: leave the USB pen inserted only for the time necessary to export data then

remove.

WARNING: if a not compatible USB pen drive is used it can cause a reset of the con-

troller

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vestfrost Congélateur

Vestfrost

Vestfrost CMFN 144 W Manuel utilisateur

Vestfrost

Vestfrost ULTF-C74i Manuel utilisateur

Vestfrost

Vestfrost NFG 309 Manuel technique

Vestfrost

Vestfrost CBI 2791 F NF E Manuel utilisateur

Vestfrost

Vestfrost VLS 064A RF AC Manuel utilisateur

Vestfrost

Vestfrost VF 10186 NoFrost Manuel utilisateur

Vestfrost

Vestfrost CFS 344 Manuel utilisateur

Vestfrost

Vestfrost VIF 11177 S Manuel utilisateur

Vestfrost

Vestfrost VF 11186 NoFrost Manuel utilisateur

Vestfrost

Vestfrost VIF 105177 S Manuel utilisateur

Vestfrost

Vestfrost ZZ 261 F Manuel utilisateur

Vestfrost

Vestfrost VLS 064A RF AC Manuel utilisateur

Vestfrost

Vestfrost MF114 Manuel utilisateur

Vestfrost

Vestfrost VR-FF372-2H0I Manuel utilisateur

Vestfrost

Vestfrost VD 205 FNS Manuel utilisateur

Vestfrost

Vestfrost ULTF-37 Manuel utilisateur

Vestfrost

Vestfrost CMF 144 W Manuel utilisateur

Vestfrost

Vestfrost FN371E W Manuel utilisateur

Vestfrost

Vestfrost MF214 Manuel utilisateur

Vestfrost

Vestfrost ULTF-37i Manuel utilisateur

Vestfrost

Vestfrost VF 11186 X NoFrost Manuel utilisateur

Vestfrost

Vestfrost VWF15FFE01W Manuel utilisateur

Vestfrost

Vestfrost MKS 044 SolarChill Manuel utilisateur

Vestfrost

Vestfrost VIF 11177 DOD NoFrost Manuel utilisateur

Manuels Congélateur populaires d'autres marques

Siemens

Siemens GU..D SERIES Manuel utilisateur

Omcan

Omcan FR-CN-0155 Manuel utilisateur

Beko

Beko FNE290E24W Manuel utilisateur

Electrolux

Electrolux ARCTIS G 8 60 50-6I Manuel utilisateur

Electrolux

Electrolux EUF2042AOX Manuel utilisateur

Dometic

Dometic CoolFreeze CFX95DZ Manuel utilisateur

Electrolux

Electrolux EUF7000W1 Manuel utilisateur

Polar Electro

Polar Electro CT330 Manuel utilisateur

MPM

MPM MPM-145-SK Series Manuel utilisateur

SAF

SAF PRESTOTIG 200AC/DC Guide rapide

Zanussi

Zanussi ZFT11407WA Manuel utilisateur

AEG

AEG A63190GT Manuel utilisateur

AEG

AEG A81000TNW0 Manuel utilisateur

Matsui

Matsui MUC50S15E Manuel utilisateur

NEFF

NEFF G4344X8 Manuel utilisateur

Frigidaire

Frigidaire FV 1246 H Manuel utilisateur

Frigidaire

Frigidaire FFC13K1AW Manuel utilisateur

Electrolux

Electrolux EU 2400C Manuel utilisateur