Verkada CM41-E Manuel utilisateur

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Install Guide

CM41-E Outdoor Mini Dome Camera

Document

Document Details

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

V1.1 (20230301)

(V1.0 first published 2020206)

Firmware

Firmware version can be verified on

Verkada Command command.verkada.com.

Introduction

What’s in the box

What you’ll need

●A working internet connection

●802.3af Power over Ethernet (PoE) switch,

or a PoE injector. For operation below

-20° C, use 802.3at PoE.

●A smartphone or laptop

●A #2 Phillips screwdriver or power drill

with a #2 Phillips driver bit

●1/4 inch (6.5mm) drill bit for wall anchors

●1/8 inch (3mm) drill bit for pilot holes

●A Cat5 or Cat6 Ethernet cable with a

5.5-6.4mm outside diameter, no boot or

jacket on the RJ45 jack

●1” hole saw for Cable Sealing Assembly

pass through

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

CM41-E Outdoor Mini

Dome Camera

Mount plate

(Attached to camera)

2x M4 Phillips Flat

Head Screws for

ACC-MNT-6

3 Wall Anchors & M4

Phillips Pan Head Screws

for Wall Mounting

2x 10-24 Phillips

Flat Head Screws

for Junction Box

Connect

For easy registration and setup, scan the QR

code on the product.

If you prefer to manually register your product,

please proceed to: verkada.com/start

1 Pack of 2

Desiccants

Mount template

(Attached to camera)

T10 Security Torx

Screwdriver

3 Cable-Sealing

Assembly Components

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Introduction

LED Behaviors

Regular operation

Solid Orange

Camera is on and booting up.

Flashing Orange

Camera is updating firmware.

Solid Blue

Camera is running, connected,

and recording data.

Network errors

1 Blue, 1 Orange

Camera is connected to the PoE, but

unable to connect to the Switch.

1 Blue, 2 Orange

Camera has not received an IP address.

1 Blue, 3 Orange

Camera has detected duplicate IP

addresses on the LAN.

1 Blue, 4 Orange

Camera is not able reach the router.

The LED will flash in a specific order,

depending on the error state. You will

see 1 blue flash, followed by a number of

orange flashes.

Example of 1 Blue, 5 Orange flash sequence

1 Blue, 5 Orange

Camera is not able to resolve Verkada

hostnames.

1 Blue, 6 Orange

Camera is not able to receive a

response from the NTP Server.

1 Blue, 7 Orange

Camera is not able to certify the SSL

connection, likely due to SSL inspection.

1 Blue, 8 Orange

Verkada endpoints are not reachable

after boot up.

Status LED

–

Installation

Connect

Remove top cover using

T10 Security Torx

Screwdriver

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Insert the Ethernet cable

into Ethernet port. Scan the

QR code for easy camera

registration and setup, or

proceed to:

www.verkada.com/start

Installation

Mount 1/4

Note

Loosen internal security screw with T10

Security Torx Screwdriver

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Mount the camera on a wall or ceiling.

Try to keep the camera 8 to 10 feet above

the ground.

Rotate camera housing counter-clockwise

and remove it from mount plate.

For best night vision, avoid overhangs or

obstructions. These may reflect the

camera’s IR illumination and reduce the

image clarity in night mode.

Installation

Mount 2/4

Note

Use the provided mounting template to

mark wall mount holes and to drill 1 inch

center hole. For other mounting scenarios,

use the mounting template to determine

the correct hole pattern.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Feed Ethernet cable through the wall.

Leave enough slack to make

cable-sealing assembly install easier.

For a solid material like wood or metal, drill

1/8 inch pilot holes. Drive mounting screws

directly into the pilot holes.

For drywall, drill 1/4 inch holes. Insert plastic

anchors into holes and drive mounting

screws into anchors.

Installation

Mount 3/4

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Assemble cable-sealing

assembly components

onto RJ45 cord.

Insert RJ45 plug into the jack.

Insert rubber seal into the body.

Twist to lock body on to the jack.

Screw the cap onto the body.

RJ45 Jack

Body

Rubber Seal

Cap

Installation

Mount 4/4

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Feed cable assembly into wall.

Align Security Screw with Mount

Plate Standoff.

Rotate the camera clockwise and

tighten Security Screw.

Security Screw Mount Plate Standoff

Installation

Grounding

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

In order to attach a ground cable to the camera, perform the following:

Align a 20AWG or larger grounding cable with a ring terminal and drive an M4-0.7 x

6mm screw (not included) through the terminal and into the threaded grounding point

on the back of the device.

Attach the other terminal of a grounding cable directly to a circuit breaker, ground rod

or earth ground.

This unit is powered by PoE through a UL Listed ITE.

Grounding

Table des matières

Autres manuels Verkada Caméra de sécurité

Verkada

Verkada CM41 Manuel utilisateur

Verkada

Verkada CD22-E Manuel utilisateur

Verkada

Verkada CD52 Manuel utilisateur

Verkada

Verkada CD51 Guide de l'utilisateur

Verkada

Verkada CD41 Manuel utilisateur

Verkada

Verkada CB52 Manuel utilisateur

Verkada

Verkada CD32-E Manuel utilisateur

Verkada

Verkada D30 Manuel utilisateur

Verkada

Verkada CB51 Manuel utilisateur

Verkada

Verkada CB51 Manuel utilisateur

Verkada

Verkada CD31 Manuel utilisateur

Verkada

Verkada CD22 Manuel utilisateur

Verkada

Verkada CD31-E Manuel

Verkada

Verkada D40 Manuel utilisateur

Verkada

Verkada CB61 Manuel utilisateur

Verkada

Verkada CM61 Manuel utilisateur

Verkada

Verkada CB51 Manuel utilisateur

Verkada

Verkada D50 Manuel utilisateur

Verkada

Verkada CM41-S Manuel utilisateur

Verkada

Verkada CF81-E Manuel utilisateur

Verkada

Verkada CD32 Manuel utilisateur

Verkada

Verkada CD62 Manuel utilisateur

Verkada

Verkada D80 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur