Verano V360 Manuel utilisateur

INSTALLATION MANUAL

AWNING V360 - ST. TROPEZ

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

* The displayed awning is the electrical version.

Content

1. Awning

2. Wall supports

3. Control

a) Manual controle: Crank handle

b) Electrical: Switch and plug

c) Remote controlled: Remote control and plug

Necessary tools

• Drilling machine

• Masonry drill 10/14 mm

• Crosshead screwdriver

• Socket wrench 10/13/17

• Allen keyset

• Tapeline

• Level

• Pencil

In case of electrical control:

• Nippers

• Flathead screwdriver

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

Specications V360 St. Tropez

0cm

100

200

300

20º

35º

Projection 250cm

200cm

300cm 350

5º

Projection

Wall mounting Sizes in mm

Front view wall support

Top view ceiling support

Awning section

Ceiling mounting

Minimal width per fabric projection

Projection [mm] Manual control [mm] Electrical control [mm]

1500 2-Armen 2060 2040

2000 2-Armen 2620 2610

2500 2-Armen 2850 2800

3000 2-Armen 3380 3330

3500 2-Armen 3870 3820

2500 3-Armen 4250 4200

3000 3-Armen 5050 5000

3500 3-Armen 5780 5730

2500 4-Armen 5600

3000 4-Armen 6660

3500 4-Armen 7640

Wall support scheme

1700

2200

2700

3200

1500

2000

2500

3000

Fabric

type

Fabric

length

[mm]

Projec-

tion

[mm]

Width [mm] Required number of wall supports

2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 8000 9000 10000 11000 12000

Dickson

3500 3500

Dickson

2 2 2 3 3 3 4 4 4 5 5 6 6 7 8

2 2 3 3 3 4 4 5 5 6 6 7 7 8

2 2 3 3 4 4 4 5 5 6 7 7 7 8

3 3 4 4 4 5 5 5 6 7 7 8 8

4 4 4 4 5 5 6 7 7 8 8 8

197

1817054

243

170

45 45

57,7

144

127,5

44,5

Back cover is optional

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

Important before mounting

rollaag

min. 30 cm

Patio door

When the awning is fully open, it hangs down under the angle. Therefore we advise to keep at least 30 centimeters

between the window frame and the awning in a situation with patio doors to the outside. When possible, it is advisable to

hang the awning higher than 30 centimeters above the window frame.

General warning

Installation of the Verano® product yourself is at your own risk. Only use this instruction as a tool and for the installation

of this specic Verano® product. If you cannot install the product yourself, you can always opt for professional installation.

The installation team of Verano® is pleased to help you.

Be careful for damages

Don’t use a knife or any other sharp object when opening the packing. This may cause damage to the content of the

package. Put the content of the package on a so surface. Be careful when drilling, falling drill cuttings can cause damages.

Check that the window frame or façade is at.

Check the installation height

Make sure that you have enough installation height on your façade to place the awning. Above the wall support

(mounting support) have to be 5 rows of stones to prevent to much pressure on the façade. This is not oen the case with

a house-extension. It is recommended to drill the installation hole in the h stone (minimum) measured from the top.

Wall strips

When there are fewer than ve rows of stones above the wall support, wall strips have to be used. These strips divide the

forces over a bigger wall surface when the walls are to weak. View page 5 for extensive instructions.

Attention! Make sure there is no installation point in the soldier course. These are oen half stones.

Soldier course

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

1.1 Marking the holes

View the stickers on the back side of the awning. See gure 1.1.

The wall supports need to be placed where the stickers are located.

The remaining wall supports should be equaly divided between the two outer supports.

Mark the drill holes of the wall supports (A) and, if necessary, the center support (B) on the wall. The holes need to be

levelled aligned both horizontal and vertical. See gure 1.2.

Make sure that at least two of the four installation holes per wall supports are located in the middle of the stone.

See gure 1.3. If necessary, use an alignment cord.

When the back cover is used you must also mark the wall supports on the back cover. Use the same measurements

between the wall supports as you used on the wall.

g. 1.2 Placing the wall supports

g. 1.1 Location stickers

middensticker sticker

muursteun

1. Installation of the wall supports

W = width of the awning

Y = window frame height plus a minimum of 30 cm

A = wall supports

AAA

W = width of the awning

center

wall support wall support wall support

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

1.3 Drilling the control hole

If you want to connect your wall control on the inside, measure the place of the control hole carefully. This depends on

your personal preference and situation.

Drill inwards with a 10 millimeter drill. When drilling through the wall, it is advisable to place a shelf against the inner side

of the wall to prevent damages to the wall.

g. 1.3a Installation of wall support

g. 1.3b Installation of back cover and wall support

1.2 Drilling the holes

Drill the installation holes. Our advise is to drill with

a 14 millimeter masonry drill in case of a wall made

of concrete or stone. Use matching plugs and bolts of

high quality. Install the wall supports (A) and, if necessary,

the center support(s) (B) and tighten the bolts.

See gure 1.3a.

When the back cover is used, also drill the holes in the

back cover. Install the back cover together with the wall

supports (A). See gure 1.3b.

1.4 Extra wall support weak wall

If there are less than ve rows of stones above the installation location, extra wall supports are needed.

The extra wall supports divide the power over a larger wall surface. This way the wall can carry more weight.

See gure 1.4.

extraextra

g. 1.4 Applying extra wall supports

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

2.1 Placing the awning

Hang the awning in the wall supports. See gure 2.1 and 2.2.

2.2 Securing the awning

Lock the wall supports by using the included locking bolts. See gure 2.3.

Attention! The awning may not be opened before the locking bolts are applied!

2. Installation of the awning

g. 2.2 Detail wall support

g. 2.1 Placing the awning

g. 2.3 Applying the locking bolts

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

3. Electrical wall control

TIP! Sealing the hole

In case of an electrical wire to the inside, we advise to seal the hole where the wire comes in. This to prevent moisture from

running inwards. Attention! Do this both on the in- and outside.

3.2 Standard factory setting

The motor control is set standardly.

See the included manual of the motor and the possible remote control.

g. 3.1 Motor le (seen from the outside) g. 3.2 Motor right (seen from the outside)

3.1 Connecting the wall control

1. Check the position of the motor (le or right), seen from the outside!

2. If you have inside control, rst guide the cable through the hole in the wall you drilled before.

3. Connect the four-wired cord of the motor and the three-wired cored with plug following the scheme below.

4. Put the plug in the power point.

5. The awning is now connected. Before you continue the installation, check if the awning rolls out correctly.

geel/groen

blauw

bruin

geel/groen

blauw zwart

bruin

geel/groen

blauw

bruin

geel/groen

blauw

zwart

bruin

geel/groen

blauw

bruin

geel/groen

blauw zwart

bruin

geel/groen

blauw

bruin

geel/groen

blauw

zwart

bruin

brown

black

blue

yellow/green

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

4.1 Connecting the remote control

1. If the power point is located on the inside, rst guide the wire through the hole in the wall you drilled before.

2. Install the plug according to the color scheme below:

Brown 220V power supply

Blue 220V power supply

Yellow/green grounding

Black (do not connect)

White (do not connect)

Orange (do not connect)

3. Put the plug in the power point.

4. The awning is now connected. Before you continue the installation, check if the awning rolls out correctly by using the

remote control.

TIP! Sealing the hole

In case of an electrical wire to the inside, we advise to seal the hole where the wire comes in. This to prevent moisture

from running inwards. Attention! Do this both on the in- and outside.

4. Remote control

INSTALLATION MANUAL AWNING V360 - ST. TROPEZ

13080130-190906EN

Subject to misprints, errors and technical modifications.

21 3

5.1 Standard factory setting

The passage height for the front bar is standard set between 1,80 and 1,90 meter at an installation height of 2,70 meter.

5.2 Setting the pitch

If you want to set the awning dierent from the standard factory setting, please follow the steps below:

1. Unroll the awning completely. The arm-connections are located le and right at the beginning of the folding arms

(on the side of the box). See gure 5.1.

2. Loosen nut #1 with one stroke (wrench 17). Li the front bar during the twisting, this way the set bolt moves easily.

See gure 5.2.

3. Completely turn out hexagon bolt #2. Then turn allen bolt #3 for the adjustment.

Le = front bar moves up, right = front bar moves down.

4. Repeat step 3 on the other side until the front bar is level.

5. WHen the front bar is at the desired height, put allen bolt #2 back in place and tighten nut #1.

Attention! Never touch the nuts with a red cross.

g. 5.2 Detail le arm-connection

g. 5.1 Location arm-connections

5. Pitch

Table des matières

Autres manuels Verano Accessoires

Verano

Verano VERANDA V905 - ISEO Manuel utilisateur

Verano

Verano V610 Oslo Manuel utilisateur

Verano

Verano V612 HAMAR Manuel utilisateur

Verano

Verano V296 Santos Manuel utilisateur

Verano

Verano V460 SANTANDER Manuel utilisateur

Verano

Verano V124 - CALPE Manuel utilisateur

Verano

Verano V124 - CALPE Manuel utilisateur

Verano

Verano V880 RAPOLLO Manuel utilisateur

Verano

Verano V805 CORTONA Manuel utilisateur

Verano

Verano V255 Salou Manuel utilisateur

Verano

Verano V480 Cannes Manuel utilisateur

Verano

Verano V285-RECIFE Manuel utilisateur

Verano

Verano V225 Porto Manuel utilisateur

Verano

Verano DROP-ARM AWNING V120 NAPOLI Manuel utilisateur

Verano

Verano Odense V640 Manuel utilisateur

Verano

Verano Mallorca Special V150 Manuel utilisateur

Verano

Verano V160 Florence Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur