Vent-Axia 478075 Manuel utilisateur

1

Acoustic Top Box

& Enclosure

For Sentinel Kinetic

Advance S & SX

Fitting Instructions

Stock Ref. No:

TOP BOX

478075 - Advance S & SX

ENCLOSURE

478080 - Advance S

478081 - Advance SX

READ IN CONJUNCTION WITH ILLUSTRATIONS

PLEASE SAVE THESE INSTRUCTIONS

2

These instructions should be read in conjunction with the Sentinel Kinetic Advance

MVHR Installation and Commissioning Manual (Vent-Axia part no. 474957).

Important: Check spigot configuration for LEFT or RIGHT HAND setup

“These units are heavy and should only mounted on walls capable of

bearing their weight i.e. a solid masonry wall or a stud wall that has been

specially constructed with extra studs and boards.”

Note: The use of sound attenuators on the ducting is recommended.

Acoustic Solution Options

Option A Option B

Top Box only + MVHR unit Enclosure only + MVHR unit

Pages 3 - 8 Pages 9 - 15

Option C Acoustic Bracket Kits

Top Box & Enclosure + MVHR unit Top Box – Option A

Pages 16 – 17 Acoustic Bracket Kit 1 – 478818

Top Box & Enclosure – Option C

Acoustic Bracket Kit 2 – 478819

Wired Remote Docking Kit

Docking Kit will be required with

“Option B & Option C” setups.

Docking Kit – 474491

3

Option A

Acoustic Top Box + MVHR unit

SIZE & WEIGHT

WEIGHT

Top Box without unit 14kg

Top Box with unit 41kg

Advance Unit 27kg

4

FIX MOUNTING BRACKETS

Use Acoustic Bracket Kit 1 (478818) to mount

Unit & Top Box.

Bracket to be mounted to 502mm centres.

MOUNTING UNIT TO BRACKETS

Once brackets are mounted, unit can be attached to hanging brackets (see view A) with the

clips on the rear of the unit. Then use the adjusting feet on the rear of the unit at the bottom,

to level the unit. Once level use the locking nut to secure it in position.

5

MOUNTING TOP BOX TO BRACKETS

1. Before mounting the Top Box, the front cover will need removed before install.

6

2. Use 4-off M5x16 screws supplied in Bracket kit 1, fix the screw in half way on the mount

brackets.

3. Then lift Top Box over the spigots and then line up the 4 screws with the key-hole slots on

the rear of the Top Box (see view B). Once all fitted, tighten all screws.

7

SPIGOT ATTACHMENT ON TOP BOX

Connect all spigots to the unit, then use duct tape to seal & secure them in place. Two foam

pieces supplied with Top Box are to be used on “To Atmosphere” & “From Atmosphere”

spigots, wrap each foam piece around base of spigots (see view C).

8

Image shows a Right Hand setup with foam

insulation fitted on “To Atmosphere” & “From

Atmosphere” spigots.

FITTING FRONT COVER TOP BOX

Once unit is installed and commissioned, as per Installation &

Commissioning instructions, then secure front panel back onto

Enclosure.

9

Option B

Acoustic Enclosure + MVHR unit

SIZE & WEIGHT

WEIGHT

Enclosure without unit 31kg

Enclosure

with unit 54kg

Advance Unit 27kg

10

FIX MOUNTING BRACKETS

Unpack mounting brackets from separate box and assemble and fix in accordance with the

Instruction leaflet supplied with the brackets to 560mm centres.

IMPOR

TANT

200mm minimum clearance

must be left under the mounting

brackets to allow access, for

tightening the mounting bolts.

Ce manuel convient aux modèles suivants

2

Table des matières

Autres manuels Vent-Axia Ventilateur

Vent-Axia

Vent-Axia Svensa Manuel utilisateur

Vent-Axia

Vent-Axia ACH100B Instructions de montage

Vent-Axia

Vent-Axia Slimpak EC Series Instructions de montage

Vent-Axia

Vent-Axia TX7 WL Instructions de montage

Vent-Axia

Vent-Axia VA140/150KP Instructions de montage

Vent-Axia

Vent-Axia T-Series Instructions de montage

Vent-Axia

Vent-Axia VASF100B Instructions de montage

Vent-Axia

Vent-Axia NBR HTP 473809 Instructions de montage

Vent-Axia

Vent-Axia Serene 8000000042 Instructions de montage

Vent-Axia

Vent-Axia QP Series Instructions de montage

Vent-Axia

Vent-Axia Centrif 179 Manuel utilisateur

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus SELV Instructions de montage

Vent-Axia

Vent-Axia HR100W Guide de l'utilisateur

Vent-Axia

Vent-Axia Lo-Carbon Silhouette 100HT Instructions de montage

Vent-Axia

Vent-Axia LuminAir Turbo Series Instructions de montage

Vent-Axia

Vent-Axia Response Series Instructions de montage

Vent-Axia

Vent-Axia Lineair LINEAIR100 B Instructions de montage

Vent-Axia

Vent-Axia VA100 Series Instructions de montage

Vent-Axia

Vent-Axia Kinetic Advance White Manuel utilisateur

Vent-Axia

Vent-Axia EKF355E1 Instructions de montage

Vent-Axia

Vent-Axia MULTIVENT MV250 Instructions de montage

Vent-Axia

Vent-Axia MULTIVENT MV250H Instructions de montage

Vent-Axia

Vent-Axia Lo-Carbon Sylph 100CV Instructions de montage

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus 427481A Instructions de montage

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage