Velodyne Subcontractor SC-600D Manuel utilisateur
SC-600D Amplifier
SC-600 IW
SC-600 IF/IC Subwoofers
USER’S MANUAL
Amplifier/Subwoofers
WWW.VELODYNE.COM Subcontractor Series User’s Manual - i
WWW.VELODYNE.COM Subcontractor Series User’s Manual - ii
TABLE OF CONTENTS
Congratulations ........................................................1
Product Features.......................................................1
– SC-600DSubwooferAmplier .......................................1
– SC-600 IW, SC-600 IF/IC Subwoofers .................................2
Setup Checklist ........................................................3
Installation ...........................................................3
– Front Panel Controls and Displays ....................................3
– Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear Panel Connections - Detailed Explanation ...............................8
– About Low-Pass Crossovers .......................................10
– A Word About Your Receiver’s Crossover and the SC-600D Crossover ......10
– A Word About Interconnect Cables...................................10
– A Word About Subwoofer Placement ................................11
Selecting the Subwoofer(s) to be Controlled ................................11
Usage ..............................................................12
Restore Defaults ......................................................15
CareofYourAmplierandSubwoofer .....................................15
Troubleshooting and Service.............................................16
Specications ........................................................17
Appendix A: RS-232 Serial Overview and Commands .........................18
Warranty ............................................................19
www.velodyne.com Subcontractor Series User’s Manual - 1
CONGRATULATIONS
CongratulationsonyourpurchaseofaVelodyne(SC)SubContractorSeries600Damplierandsubwoofer.This
system represents the state-of-the-art in low frequency reproduction. Read and follow the instructions below to
ensure safe and proper system operation.
Warning!
To prevent re or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do
not open speaker enclosure or amp chassis cover. Please observe all warnings on the equipment itself. There
are no user serviceable parts inside. Please refer all service questions to your authorized Velodyne dealer.
Prior to Installation:
Please unpack the system carefully. Please save the carton and all packaging materials for future use. Record
the serial number in the space provided on the warranty card and page 20 of this manual for future reference.
Product Features
SC-600DSubwooferAmplier
• 400wattsdynamic/200wattsRMShigheciency,ClassD
• DSP-controlled
• Fourselectablepresetsforcustomizedlisteningmode
• Automatic5-bandroomequalizer(microphoneincluded)
• Night-modesetting
• Mutecontrol
• Line-level(RCA)inputsandoutputs
• Speaker-levelinputswith5waybindingpostconnections
• Signalsensingautoturnon/o(defeatable)
• Variablevolumecontrol
• Selectablephasecontrol(0,90,180or270degrees)
• Built-inadjustable(30-160Hz)digitallow-passcrossoverwith24dB/octaveslope
• DriverDisplacementControlsoftwaretopreventoverexcursionandampclipping
• BluepowerindicatorLED
• RS-232SerialInterface
• 12Volttrigger
• UniversalIRrepeatermini-jack
• Preset-specicsubsoniclter
www.velodyne.com
2 - Subcontractor Series User’s Manual
SC-600 IW, SC-600 IF/IC SUBWOOFERS
SC-600 IW (In-Wall):
- Two high excursion 6.5” active drivers, two 12.5” x 3” oval passive radiators with ribbed rubber surround
- High-excursionrubbersurroundsonbothactiveandpassivedrivers
- 2” 4 layer copper
- FrequencyResponse:30-120Hz(+/-3dB)
- 4 ohm impedance
SC-600 IF/IC (In-Floor/In-Ceiling):
- 12” (9.7” piston diameter) subwoofer
- 2.5” 4 layer copper
- Oversizedspiderforlinearityathighexcursion
- High-excursionrubbersurround
- FrequencyResponse:25-120Hz(+/-3dB)
- 4 ohm impedance
Note: TheSC-600IWandtheSC-600IF/ICmustbedrivenwitheithertheSC-600DortheSC-602amplier.
Use of any other power source voids the warranty.
SETUP CHECKLIST
Besuretodothefollowingtoensurethebestperformancefromyoursubwoofer(s):
Ifpossible,optimizetheplacementofthesubwoofer(s)inthelisteningarea.Seepage10oftheUser’s
Manual.
Install and wire the subwoofer per the instructions on pages 3 - 8.
Select the proper model per the instructions on page 10.
Select the proper volume level. See page 4.
Besurethelowpasscrossoverissetcorrectly.Seepages8-9.
BesuretoequalizethesubwooferusingthemicrophoneandAuto-EQfeature.Seepage11.
Besuretosetthephasecontrolontheremote.Seepage11.
Select the correct preset for the source material. See page 13.
Your new Velodyne subwoofer system provides for a number of installation options. Read all the installation
information below in order to determine which installation option is best for your system. Remember to perform
allinstallationprocedureswithsystempowerturnedo.
Note: For proper setup and installation of the SC-600 IW (In-Wall) subwoofer, please refer to the SC-600 IW
QuickInstallGuide.
www.velodyne.com Subcontractor Series User’s Manual - 3
INSTALLATION
FRONT PANEL CONTROLS AND DISPLAYS
Figure 1: Front Panel Connections of the SC-600D amplier..
Following are brief descriptions of the controls described in Figure 1. More detail on these
controls can be found in the next section.
(1) Power Switch
ThisbuttonforcesyourSC-600Damplierintostandbymode.ThepowerLEDturnsamber,thenumeric
LEDshutso,andtheamplierputsoutnopower.TheunitwillremaininthismodeuntilthePOWER
button is pressed again. To fully deactivate (i.e. power down) the unit, use the main power switch on the
back panel.
(2) Power LED
ThisLEDilluminateswhenthepowerison.Blueindicatesnormaloperation.TheLEDturnsamber
when the unit is in standby mode or the remote has been used to deactivate the unit, and dims when
the unit is in night mode.
(3) Mic Input
ConnectthesuppliedmicrophonefortheAuto-EQfeaturetothismini-jackinput.
(4) Remote Eye
This is the eye that receives infrared commands from the supplied remote.
(5) Crossover
Use these Up and Down buttons to select the frequency below which all signals will be routed to the
subwoofer(forexample,80Hz),ratherthattothemainspeakers.ThefrequencyisindicatedontheLED
display,thenthedisplayrevertstoshowingthesubwoofer’svolumelevel.Theslopeisxedat24dB/
octave.Todeactivatethecrossover,pressBOTHtheUpandDowncrossoverbuttonsatthesametime
– two dashes on the display indicate the crossover is deactivated and the woofer plays all frequencies
presented to it. Please see page 8 for a more detailed discussion on crossovers.
www.velodyne.com
4 - Subcontractor Series User’s Manual
(6) LED Numeric Indicator
This LED supplies information on volume, crossover, woofer type, and other information. The “light”
button on the remote deactivates this display. Upon startup, the display shows the model of subwoofer
the SC-600D amp is controlling, then reverts to the volume indicator.
(7) Volume Control
These buttons allow you to balance the output from the subwoofer to the main speakers in your system.
The volume should be set to achieve similar volume level from between both the main speakers and
subwoofer. The default volume is 30.
Note: Volume is also controllable by using the supplied remote.
WARNING: Some manufacturers preset their receivers with the Sub-Out (a.k.a. LFE) channel signal
at a minimum level. It is very important to verify that your receiver Sub-Out channel is set to the same
output level as your front right and left channels. Refer to your receiver manual for the individual channel
level adjustment procedure. If your receiver Sub- Out channel is set too low, the subwoofer may appear
to have a weak output, it may sound noisy or distorted, and the Auto On/Off feature may not operate
properly.
(8) Optional Rack Mount Ears (Included)
Following are brief descriptions described in Figure 2. More detail on these controls can be found in the
next section.
Figure 2: Rear Panel Connections of the SC-600D amplier.
(9) Thru Jacks (See Figure 3A)
These RCA connectors are for passing along the same signal that goes into your subwoofer to a second
“daisy-chained” subwoofer. The signal from these RCA connectors is the same as the input signal.
(10) Line Input / LFE Input (See Figure 3A & 3B)
ConnectthesejackstotheLINEOUTpreampoutput,LFEoutput,orsubwooferoutputjacksofyour
receiver/processor. If using the LFE output from your receiver or processor, plug the single cable into
thejacklabeledLFEinputor,formoresignal,usea“Y”connector(notincluded)andfeedthesignalinto
both “R” and “L” inputs.
Autres manuels pour Subcontractor SC-600D
1
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels Velodyne Amplificateur
Velodyne
Velodyne SUBCONTRACTOR SC-600 Amplifier Manuel utilisateur
Velodyne
Velodyne SC-600 - REV C Manuel utilisateur
Velodyne
Velodyne Subcontractor SC-602 Manuel utilisateur
Velodyne
Velodyne Subcontractor SC-600D Manuel utilisateur
Velodyne
Velodyne Subcontractor SC-602 Manuel utilisateur
Velodyne
Velodyne SUBCONTRACTOR SC-600 Amplifier Manuel utilisateur
Velodyne
Velodyne SubContractor Series SC-1250 Manuel utilisateur
