Vantec UGT-ST310R Manuel utilisateur

6-Port SATA II 150 PCI Host

Card w/RAID

User Manual

Model: UGT-ST310R

All brand names and trademarks are properties of their respective owners.

w w w . v a n t e c u s a . c o m

UGT-ST310R Page 2

Table of Contents

1. Bus Interface..........................................3

2. Connectors.............................................3

3. Package Contents..................................3

4. System Requirements............................4

5. Hardware Description.............................4

6. Hardware Installation .............................5

7. Device Connection.................................5

8. RAID Arrays...........................................6

RAID 0 (Striping).................................6

RAID 1 (Mirror) ...................................8

RAID 0+1 (Mirroring + Striping) ..........9

RAID 5 (Parity).................................. 11

CONCATENATION (JBOD)..............13

9. BIOS Configuration..............................15

10. Driver Installation .................................15

UGT-ST310R Page 3

Features

•Silicon Image SiI3114 SATA controller chip

•Compliant with PCI Specification, Rev. 2.3, 32-bit, 33/66Mhz

•Compliant with Serial ATA1.0 specification

•Provides four independent channels to support up to four

Serial ATA drives

•Supports RAID0 (striping), RAID1 (mirroring), RAID5 (Parity

RAID), RAID 0+1(mirroring + striping) and Concatenation

(JBOD), Individual Mode

•HDDs function normally when not in RAID sets

•Supports SATA up to 150MB/Sec

•Supports Windows® 2000, XP/2003 32/64 bit, Vista 32/64bit

Bus Interface

zPCI Bus 32 bit

Connectors

z4 x internal SATA connectors

z2 x external eSATA connectors

Package Contents

z1 x 6-Port SATA II 150 PCI Host Card w/RAID

z1 x Driver CD

z2 x SATA Data Cable

z1 x User’s Manual

System Requirements

zPentium-class computer with one available PCI slot

zWindows® 2000, XP/2003 32/64bit, Vista 32/64bit

Hardware Description

G (Jumper Settings)

JP Description Active Port

1-2 close Enable SATA Connector

J1-J4

2-3 close Enable SATA Connector

1-2 close Enable SATA Connector

J5-J8

2-3 close Enable SATA Connector

UGT-ST310R Page 4

UGT-ST310R Page 5

Note: There are six SATA ports in 6-Port SATA II 150 PCI Host

Card w/RAID. We name these ports from A through F. Ports A to

D are internal SATA ports. Ports E and F are external SATA ports.

Changing the jumper settings allows you to select between

external and internal ports to use. By default, Port A, B, C and D

are working.

Hardware Installation

1. Turn Off the power to your computer and any other

connected peripheral devices.

2. Unplug the power cord form the back of the computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. To install the card, carefully align the card’s bus connector

with the selected PCI slot on the motherboard. Push the

board down firmly, but gently, until it is well seated.

6. Replace the slot bracket’s holding screw to secure the card.

Device Connection

The 6-Port SATA II 150 PCI Host Card w/RAID is a four channel

Serial ATA controller that supports up to four Serial ATA hard disk

drives. It is recommended to use identical hard drives for all

RAID configurations.

1. Install your hard disk drive(s) in chassis.

2. Connect the Serial ATA hard disk drive to the system power

supply using the included Serial ATA power cable.

3. Connect one end of the Serial ATA cable to the hard disk

UGT-ST310R Page 6

drive.

4. Attach the other end of the Serial ATA cable to the Serial

ATA controller on the 6-Port SATA II 150 PCI Host Card

w/RAID.

5. Follow the same instructions to connect up to four hard

drives. Device connection is now complete.

6. Replace the computer cover and reconnect the power cord.

RAID Arrays

RAID Arrays are setup in the 6-Port SATA II 150 PCI Host Card

w/RAID’s BIOS.

RAID 0 (Striping)

This RAID array to be used on New/Blank hard drives. Striping

will destroy existing data on the hard drive. Auto Configuration

is recommended. For applications that require custom chunk

size, Manual Configuration is offered.

Auto configuration (recommended)

The default chunk size is 64k when selecting Auto

configuration.

1. As the BIOS boots press Ctrl+S or F4 when prompted to

enter the RAID BIOS.

2. At the next screen select Create RAID Set, then press

Enter.

UGT-ST310R Page 7

3. Select RAID0, then press Enter.

4. Select the number of drives then press Enter.

5. Select Auto configuration, then press Enter.

6. Input the RAID size, press Enter.

7. When asked Are You Sure (Y/N)?, press Y to accept.

8. Press Ctrl+E to exit the BIOS.

9. When asked Are you sure to exit (Y/N)?, press Y to exit

and reboot.

10. Continue with FDISK and FORMAT steps as if you were

installing a conventional hard drive.

Manual configuration

1. As the BIOS boots press Ctrl+S or F4 when prompted to

enter the RAID BIOS.

2. At the next screen select Create RAID Set, then press

Enter.

3. Select RAID0, then press Enter.

4. Select the number of drives then press Enter.

5. Select Manual configuration then press Enter

6. Select chunk size from 8k, 16k, 32k, 64k or 128k, then

press Enter.

7. Select the first drive, press Enter.

8. Select the second drive, press Enter.

9. If applicable select the 3rd and 4th drives pressing enter

after each selection.

10. Input the RAID size, press Enter.

11. When asked Are You Sure(Y/N)?, press Y to accept.

12. Press Ctrl+E to exit the BIOS.

13. When asked Are you sure to exit(Y/N)?, press Y to exit

and reboot.

14. Continue with FDISK and FORMAT steps as if you were

installing a conventional hard drive.

UGT-ST310R Page 8

RAID 1 (Mirror)

For New/Blank Hard Drives

1. As the BIOS boots press Ctrl+S or F4 when prompted to

enter the RAID BIOS.

2. At the next screen select Create RAID Set, then press

Enter.

3. At the next screen select RAID1 then press Enter.

4. Select Auto configuration, then press Enter.

5. Input the RAID size, press Enter.

6. When asked Are You Sure(Y/N)?, press Y to accept.

7. Press Ctrl+E to exit the BIOS.

8. When asked Are you sure to exit(Y/N)?, press Y to exit

and reboot.

9. Continue with FDISK and FORMAT steps as if you were

installing a conventional hard drive.

For Existing Hard Drives with Data

1. As the BIOS boots press Ctrl+S or F4 when prompted to

enter the RAID BIOS.

2. At the next screen select Create RAID Set, then press

Enter.

3. At the next screen select RAID1 then press Enter.

4. Select Manual configuration, then press Enter.

5. Select the Source drive, press Enter.

6. Select the Target drive, press Enter.

7. Select Create with data copy, then press Enter.

8. Select online copy, then press Enter.

Note: Selecting Online Copy builds the mirror while in

Windows. Selecting Offline Copy builds the mirror before

exiting the RAID BIOS.

UGT-ST310R Page 9

9. Input the RAID size, press Enter.

10. Press Ctrl+E to exit the BIOS.

11. When asked Are you sure to exit(Y/N)?, press Y to exit

and reboot.

Note: If during boot the RAID BIOS reports an RAID1 set is in

Rebuild status, The rebuild will continue after boot

sequence is complete, disregard the message, continue

booting, and let the Mirror rebuild.

Rebuilding a Failed Mirror Set

When a failure to one member occurs, you will be notified either

by the RAID BIOS during boot or by the SATARAID5 GUI while

in Windows. The steps below will guide you in rebuilding a failed

mirror set.

1. Replace the failed drive with one of equal or greater

capacity, then start the computer.

2. During boot press Ctrl+S or F4 to enter the RAID BIOS.

3. Select Create RAID Set then press Enter.

4. Select SPARE DRIVE then press Enter.

5. Select the replacement drive then press Enter.

6. When asked Are You Sure(Y/N)?, press Y to confirm.

7. Press Ctrl+E to exit.

8. When asked Are you sure to exit(Y/N)?, press Y to exit.

RAID 0+1 (Mirroring + Striping)

This RAID array to be used on New/Blank hard drives, do not

UGT-ST310R Page 10

use existing hard drive(s) with data. To create a RAID 0+1 set

four hard drives are required.

Auto configuration (recommended)

The default chunk size is 64k when selecting Auto

configuration.

1. As the BIOS boots press Ctrl+S or F4 when prompted to

enter the RAID BIOS.

2. At the next screen select Create RAID Set, then press

Enter.

3. Select RAID10, then press Enter.

4. Select Auto configuration, then press Enter.

5. Input the RAID size, press Enter.

6. When asked Are You Sure(Y/N)?, press Y to accept.

7. Press Ctrl+E to exit the BIOS.

8. When asked Are you sure to exit(Y/N)?, press Y to exit

and reboot.

9. Continue with FDISK and FORMAT steps as if you were

installing a conventional hard drive.

Manual configuration

1. As the BIOS boots press Ctrl+S or F4 when prompted to

enter the RAID BIOS.

2. At the next screen select Create RAID Set, then press

Enter.

3. Select RAID10, then press Enter.

4. Select the number of drives then press Enter.

5. Select Manual configuration then press Enter.

Table des matières

Autres manuels Vantec Carte PCI

Vantec

Vantec UGT-ST644R Manuel utilisateur

Vantec

Vantec SATA 150 PCI RAID Card Manuel utilisateur

Vantec

Vantec UGT-ST622 Manuel utilisateur

Vantec

Vantec eSATA PCI & PCI-E Card & CardBus Manuel utilisateur

Vantec

Vantec UGT-PC20SR Manuel utilisateur

Vantec

Vantec UGT-PCE430-2C Manuel utilisateur

Vantec

Vantec UGT-PC302 Manuel utilisateur

Vantec

Vantec UGT-PC10PL Manuel utilisateur

Vantec

Vantec UGT-IS100R Manuel utilisateur

Vantec

Vantec UGT-FW050 Manuel utilisateur

Vantec

Vantec FireWire 400 Manuel utilisateur

Vantec

Vantec UGT-PC2S1P Manuel utilisateur

Vantec

Vantec 2+1 Serial & Parallel PCI Host Card Manuel utilisateur

Vantec

Vantec 2+1 FireWire 800/400 PCIe Combo Host Card Manuel utilisateur

Vantec

Vantec UGT-PC341 Manuel utilisateur

Vantec

Vantec UGT-ST320R Manuel utilisateur

Vantec

Vantec UGT-PC210 Manuel utilisateur

Vantec

Vantec UGT-PC312 Manuel utilisateur

Vantec

Vantec 3-Port FireWire 400 PCIe Host Card Manuel utilisateur

Vantec

Vantec UGT-PC371AC Manuel utilisateur

Vantec

Vantec UGT-PC345 Manuel utilisateur

Manuels Carte PCI populaires d'autres marques

ERMA

ERMA SSI 1417 Manuel utilisateur

SIIG

SIIG CyberSerial Dual PCI Instructions de montage

Moxa Technologies

Moxa Technologies CP-102E Manuel utilisateur

I-Bus

I-Bus IBC2602 Manuel utilisateur

Exsys

Exsys EX-60102 Manuel utilisateur

Chelsio Communications

Chelsio Communications T5 Series Manuel utilisateur

Conrad Electronic

Conrad Electronic 97 46 71 Manuel utilisateur

Micro Innovations

Micro Innovations USB650A Manuel utilisateur

KTI Networks

KTI Networks KF-310 Manuel utilisateur

Asus

Asus SpaceLink WL230 Manuel utilisateur

SIIG

SIIG SC2475 Manuel utilisateur

TRENDnet

TRENDnet TEW-703PI Manuel utilisateur

Belkin

Belkin F5D7000F Manuel utilisateur

Pericom

Pericom PI7C7100 Manuel utilisateur

ADLINK Technology

ADLINK Technology cPCI-3548 Manuel utilisateur

Digium

Digium TE200 Series Manuel utilisateur

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur

Western Digital

Western Digital FireWire PCI Adapter Manuel utilisateur