Vanco Evolution EV4K7014 Manuel utilisateur
Vanco Part Number:
EV4K7014
4K 1x4 HDMI®
Splitter over Cat6
Cable with HDMI
Loop-Out
www.vanco1.com • 800.626.6445
4K 1x4
HDMI® Splitter
over Cat6 Cable with HDMI
Loop-out
www.vanco1.com 800.626.6445
2
1. Do not expose this unit to water, moisture, or
excessive humidity.
2. Do not install or place this unit in a built-in
cabinet, or other conned space without
adequate ventilation.
3. To prevent risk of electrical shock or re
hazard, due to overheating do not obstruct
unit’s ventilation openings.
4. Do not install near any source of heat,
including other units that may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening storms or when
not used for an extended period of time. A
surge protector is strongly recommended.
8. Protect the power cord from being walked on
or pinched, particularly at the plugs.
9. Use unit only with accessories specied by
the manufacturer.
10. Refer all servicing to qualied personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal and the same
video resolution and audio settings on all electronic equipment in the system. When there are multiple
sources and displays, the video resolution and audio setting on all connected units must be adjusted
to correspond with that of the display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
This product is 100% inspected and tested in the United States to verify
HDMI performance parameters.
www.vanco1.com 800.626.6445 3
INTRODUCTION
The EV4K7014 is an HDMI splitter that allows one HDMI input to be split and sent to up to ve displays simultaneously.
With four outputs over UTP, and one output over HDMI, the EV4K7014 allows for a local display connected, or to daisy chain
additional units to gain more outputs. The EV4K7014 includes four receivers (EV4K7014-RX) as a kit, which are PoE, which
do not require any power supplies at the display end. Extends 4K@60Hz 4:4:4 with HDR10 and IR control up to 230ft/70m
over a single Cat6 cable. IR accessories are included to allow IR pass through for controlling the source at each UTP display
location. For splitting and distributing one single source to multiple displays, while extending over Cat6, the EV4K7014 is a
great solution for any application with the ability to expand.
*NOTE - All specications and ratings for the EV4K7014 have been tested and conrmed using Cat6 cabling.
Cat6 or better is strongly recommended for optimum performance, achieve rated distance, and to maximize
resolution capabilities of this product. Cat5e is not recommended and may not achieve distance and/or
resolution expectations.
FEATURES
Evolution 4K 1x4 HDMI Splitter over Cat6 Cable with HDMI Loop-out
Part # EV4K7014
• Allows a single source to be split and extended to multiple displays
• Complete kit with (4) PoE Receivers included
• Features an additional HDMI output which can be used for a local display or to cascade to another
splitter for a larger distribution system
• Transmission Range: Extends 4K@60Hz, 4:4:4 Chroma with HDR10 and IR up to 230ft/70m and 1080p
up to 330ft/100m over a single Cat6 cable
• Features Power over Ethernet (PoE) Technology which transmits power over Cat6, allowing the receivers
to be powered without connecting a power supply
• Latency under 30ms
• Supports bi-directional IR (20~60kHz) for source or display control
• IR accessories included allowing for source control from each UTP display location
• Features auto and manual EDID options for compatibility with source and displays
• Digital audio breakout on the receivers for source audio extraction
• HDCP 1.4/2.2 compliant
• Slim and compact design
• RS232 control of splitter
• Pure uncompressed 7.1 ch digital audio
• Supports DTS-HD and Dolby TrueHD high bit rate audio
• Splitter Dimensions: 14.3” L x 4.09 W x 0.9” H (264.40mm L x 104 mm W x 23.85mm H)
• Receiver Dimensions: 4.17” L x 3.8” W x 0.75” H (106 mm L x 99mm W x 19.20mm H)
www.vanco1.com 800.626.6445
4
SPECIFICATIONS
Power....................................................................... 12V, 3A power supply included
Dimensions .............................................................. Splitter Dimensions: 14.3” L x 4.09 W x 0.9” H
(264.40mm L x 104 mm W x 23.85mm H); Receiver Dimensions: 4.17” L x 3.8” W x 0.75” H (106 mm L x
99mm W x 19.20mm H)
Weight…………………………. ................................ Splitter: 1.4 lbs (640g); Receiver: 0.5 lbs (210g)
Resolution and Distance over Cat6 .............................. 4K@60Hz, 4:4:4 Chroma and HDR10 up to
230ft/70m, 1080P@60Hz up to 330ft/100m
Audio Formats........................................................... PCM, Dolby True HD and DTS master
HDMI Interface Standard ............................................ HDMI 2.0b, HDCP 1.4/2.2
Remote IR................................................................. 20~60KHZ wide frequency carrier
ESD Level ................................................................. HBM +/- 4kv (contact discharge)
Temperature Range.................................................... 0~60 degrees Celsius
(Operate), -20~70 degrees Celsius
Compliance ............................................................... FCC, CE, RoHS
• (1) EV4K7014 1x4 Splitter
• (4) EV4K7014 PoE Receivers
• (1) IR Blaster
• (4) IR Receivers (display)
• (1) 3-pin terminal block (phoenix connector)
• (1) 12V/3A power supply
• (1) Set of mounting hardware and screws
• (1) Product Manual
PACKAGE CONTENTS
www.vanco1.com 800.626.6445 5
PANEL DESCRIPTIONS
1. Power Indicator: Illuminates blue when the power is turned on
2. Reset Button: Reboots the splitter
3. IR IN: Connect the included IR Receiver (RX) to receive the IR signal from a remote
4. IR OUT: Connect the included IR Blaster (TX) and place at the source for IR control
5. RJ45 Output Ports: Connect to receivers with Cat6 cabling
Note: Home-run cabling strongly recommended without any couplings, punch-downs, or patch panels;
Cat5e not recommended
6. HDMI Output Port: Connect to an HDMI display, or connect to an additional EV4K7014 to cascade to
create additional outputs
7. HDMI Input Port: Connect an HDMI source device
8. EDID Dip Switch: Set output compatibility resolution
9. RS-232 Port: Connects to control the splitter
10. Power: Connect the provided DC 12V/3A power adapter
1
23 4 56 7 89
10
EV4K7014 Splitter
www.vanco1.com 800.626.6445
6
1. Reset button: Reboots the receiver
2. Cat6 Input: Connect a single Cat6 with other end of cable connected to the splitter unit (home-run cabling
strongly recommended without any couplings, punch-downs, or patch panels)
3. Power/Signal LED: When there is power and no HDMI source signal, the indicator will ash; when there is
power and a source HDMI signal, the indicator will emit solid blue
4. DC 12V Port: No power supply needed, splitter will provide power over Cat6 (PoE) to the receiver units
5. S/PDIF OUT: Digital Optical Audio break out that will output source signal audio; connect to an external
amplier, soundbar, and/or audio distribution component
6. HDMI OUT: Connect a display such as an HDTV or HD Projector
7. IR IN: Connect the included IR Receiver (RX); see IR section for setup
8. IR OUT: Connect the included IR Blaster (TX); see IR section for setup
12 3
4
PANEL DESCRIPTIONS
5
67 8
EV4K7014 Receiver
www.vanco1.com 800.626.6445 7
CONNECTION DIAGRAM
CONNECT AND OPERATE
1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc.
to the HDMI input
2. Connect the Cat6 runs (home run cabling recommended) to the UTP output(s); connect to the EV4K7014
RX Receivers
3. Connect displays such as an HDTV or HD Projector to the HDMI output of the EV4K7014 RX Receivers
4. (Optional) Connect a display such as an HDTV or HD Projector to the HDMI output of the EV4K7014; or
connect an additional EV4K7014 to cascade to create additional outputs
5. For power, connect the provided power supply
HDTV
IR Blaster
HDTV
HDMIHDMIHDMIHDMI
HDMI HDMI
Source
HDTV
HDTV
IR Receiver
Cat6 Cat6 Cat6 Cat6
IR Receiver IR Receiver
IR Receiver
www.vanco1.com 800.626.6445
8
EDID MANAGEMENT
There are 16 built-in EDIDs in the product, which can be adjusted via the DIP switches. The upward DIP switch
indicates “1”, and the downward DIP switch indicates“0”. After the adjustment is made, power cycle the
EV4K7014. View displays for changes.
www.vanco1.com 800.626.6445 9
RS-232 CONTROL
The default conguration is as follows:
Baud rate: 9600, Data bits: 8, Stop bits: 1, Parity: 0
www.vanco1.com 800.626.6445
10
IR PASS-THROUGH
The IR system allows you to control the source that
is connected to the splitter unit, from the display(s).
The IR system also allows you to control the
display(s) from the splitter location (see “To Control
the Displays” section”). Additional IR receivers
(EVIR4K70-RX) and IR blasters (EVIR4K70-TX) are
sold separately.
To Control the Source:
1. Plug the IR blaster into the
IR OUT port of the splitter unit;
place blaster in front of the IR
eye of the source
2. Plug the IR Receiver into the
IR IN Port of the receiver unit;
place receiver at or near display
Table des matières
Autres manuels Vanco Câbles et connecteurs
Vanco
Vanco 280718 Manuel utilisateur
Vanco
Vanco 280902 Manuel utilisateur
Vanco
Vanco Evolution EVSLIM12 Manuel utilisateur
Vanco
Vanco Evolution EVSP4K12 1x2 Manuel utilisateur
Vanco
Vanco Evolution EVSP1017 Manuel utilisateur
Vanco
Vanco EVSLIM14 Manuel utilisateur
Vanco
Vanco Evolution EVSP4K12 1x2 Manuel
Vanco
Vanco Evolution EVSP12SC Manuel utilisateur
