Valor Fires 754 Instructions d'utilisation
5113454/04
© Baxi Heating U.K. Limited 2007.
Model754
INSET LIVE FUEL EFFECT GAS FIRE
Fitted with an
Arturafascia
(GC No. 32-032-59)
We trust that this guide gives
sufficient details to enable this
appliance to be installed and
maintained satisfactorily. However, if
further information is required, our
Valor Fires Technical Helpline will
be pleased to help.
Telephone 0844 8711 565 (National
call rates apply in the United
Kingdom).
In the Republic of Ireland
Telephone 0044 844 8711 565.
INSTALLER: Please leave this guide with the
owner
INSTALLER AND OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
All rights reserved. No part of this publication may be reproduced in any material form
(including photocopying), stored in any medium by electronic means (including in any
retrieval system or database) or transmitted, in any form or by any means, whether
electronic, mechanical, recording or otherwise, without the prior written permission of
the copyright owner.
Applications for the copyright owner's permission to reproduce any part of this
publication should be made, giving details of the proposed use, to the following
address: The Company Secretary, Baxi Heating UK Limited, The Wyvern Business
Park, Stanier Way, Derby, DE21 6BF.
Warning: Any person who does any unauthorised act in relation to a copyright work
may be liable to criminal prosecution and civil claims for damages.
Valor Fires, Erdington, Birmingham B24 9QP
www.firesandstoves.co.uk
Because our policy is one of constant development and improvement, details may vary slightly from
those given in this publication
Page 2
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).
UNDER NO CIRCUMSTANCES IS THIS FIRE TO BE CONVERTED TO LPG.
AN LPG KIT DOES NOT EXIST FOR THIS GAS FIRE.
THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED
KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).
Safety First.
Valor Fires fires are CE Approved and designed to meet the appropriate British
Standards and Safety Marks.
Quality and Excellence.
All Valor Fires fires are manufactured to the highest standards of quality and
excellence and are manufactured under a BS EN ISO 9001 quality system accepted
by the British Standards Institute.
The Highest Standards
Valor Fires is a member of SBGI and HHIC (Heating and Hot water Industry Council)
that work to ensure high standards of safety, quality and performance.
Careful Installation
Valor Fires is a CORGI registered company. All our gas fires must be
installed by a competent CORGI Registered Installer in accordance
with our Installer Guide and should not be fitted directly on to a
carpet or floor of combustible material.
Page 3
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Page 4
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
INSTALLERGUIDE
FOR OWNER GUIDE SEE PAGES 34 TO 47
CONTENTS
Section Heading Page
INSTALLER GUIDE 4 - 33
OWNER GUIDE 34 - 47
1. SAFETY 6
2. ACCESSORY LIST 6
3. APPLIANCE DATA 7
4. GENERAL INSTALLATION REQUIREMENTS 8
5. PACK CONTENTS 15
6. FIREPLACE CHECK 17
7. IGNITION CHECK 18
8. GAS SUPPLY CONNECTION 18
9. PREPARING APPLIANCE FOR INSTALLATION 19
10. HOTBOX INSTALLATION 22
11. BURNER & SUPPLY PIPE INSTALLATION 24
11.1 Fitting the burner. 24
11.2 Supply pipe installation. 24
11.3 Preliminary burner checks. 24
11.4 Check inlet pressure. 25
12. FASCIA INSTALLATION 26
13. FITTING THE CERAMIC FUEL EFFECT 26
14. FULL OPERATING CHECKS 27
14.1 Check the control settings. 27
14.2 Check for spillage. 27
15. FINAL REVIEW 29
16. SERVICING & PARTS REPLACEMENT 30
16.1 To remove the fascia. 30
16.2 To remove the burner unit. 31
16.3 To remove the pilot unit. 31
16.4 To remove the gas valve. 31
16.5 To remove the piezo generator. 32
16.6 To grease the control tap. 32
16.7 To replace the burner. 32
16.8 To remove the main burner injector. 33
16.9 To remove the appliance from the fireplace. 33
Page 5
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
1. SAFETY
Installer
Before continuing any further with the installation of this appliance please read the
following guide to manual handling:
! The lifting weight (kg) of this appliance is as below:
Heat engine Casting Fascia Total
6.80 3.84 3.00 13.64
! One person should be sufficient to lift the fire. If for any reason this weight is
considered too heavy then obtain assistance.
!
When lifting always keep your back straight. Bend your legs and not your back.
! Avoid twisting at the waist. It is better to reposition your feet.
!
Avoid upper body/top heavy bending. Do not lean forward or sideways whilst
handling the fire.
!
Always grip with the palm of the hand. Do not use the tips of fingers for support.
! Always keep the fire as close to the body as possible. This will minimise the
cantilever action.
! Use gloves to provide additional grip.
! Always use assistance if required.
2. ACCESSORY LIST
The following accessories are available: -
Description Part Number
Pre cast and clay flue block spacer kit 05654K1
Page 6
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
3. APPLIANCE DATA
Under no circumstances is this fire to be converted to LPG. An LPG conversion kit
does not exist for this gas fire.
The appliance information label is located on a plate at the base of the fire. This can
be seen by lifting the bottom front cover of the fascia - See figure 5
on the last page
of the owner guide.
This product uses fuel effect pieces containing Refractory Ceramic Fibres
(RCF), which are man-made vitreous silicate fibres. Excessive exposure to
these materials may cause irritation to eyes, skin and respiratory tract.
Consequently, it is important to take care when handling these articles to
ensure that the release of dust is kept to a minimum. To ensure that the release
of fibres from these RCF articles is kept to a minimum, during installation and
servicing we recommend that you use a HEPA filtered vacuum to remove any
dust and soot accumulated in and around the fire before and after working on
the fire. When replacing these articles we recommend that the replaced items
are not broken up, but are sealed within a heavy duty polythene bag, clearly
labelled as RCF waste. RCF waste is classed as a stable, non-reactive
hazardous waste and may be disposed at a landfill licensed to accept such
waste. Protective clothing is not required when handling these articles, but we
recommend you follow the normal hygiene rules of not smoking, eating or
drinking in the work area and always wash your hands before eating or
drinking.
This appliance does not contain any component manufactured from asbestos or
asbestos related products.
Page 7
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Gas Natural (G20)
Inlet Pressure 20mbar
Input Max. (Gross) 5.1kW (17,400 Btu/h)
Input Min. (Gross) 3.0kW (10,236 Btu/h)
Inlet Test Pressure (Cold) 20.0 ± 1.0mbar (8.0 ± 0.4in w.g.)
Gas Connection 8mm pipe
Burner Injector Stereomatic Cat. 82 Size 065
Pilot & Atmosphere Sensing Device Copreci Ref. O.D.S 21500/166
Ignition
Integral piezo (Mounted on gas valve)
Aeration Non-adjustable
The efficiency of this appliance has been measured as specified in BS 7977 - 1 and
the result is as below :
Model
Efficiency % (Gross)
754 Artura 51
The gross calorific value of the fuel has been used for this efficiency calculation. The
test data from which it has been calculated has been certified by Advantica
Certification services (0087). The efficiency value may be used in the UK
Government's Standard Assessment Procedure (SAP) for energy rating of dwellings.
The convertion of net efficiency to gross was achieved by multiplying the net
efficiency by the following conversion factor from Table E3 of SAP 2005, rounding
down to the nearest whole number.
4. GENERAL INSTALLATION REQUIREMENTS
4.1 The installation must be in accordance with these instructions.
For the user’s protection, in the United Kingdom it is the law that all gas appliances
are installed by competent persons in accordance with the current edition of the Gas
Safety (Installation and Use) Regulations. Failure to install the appliance correctly
could lead to prosecution. CORGI requires its members to work to recognised
standards.
In the United Kingdom the installation must also be in accordance with:
All the relevant parts of local regulations.
All relevant codes of practice.
The relevant parts of the current editions of the following British Standards:-
BS 715
BS EN 1856 Part 1
BS 1251
BS EN 1858 which replaces BS 1289 Part 1
BS EN 1806 which replaces BS 1289 Part 2
BS EN 1856 Part 1 which replaces BS 4543 Part 2
BS 5440 Part 1
BS 5440 Part 2
BS 5871 Part 2
BS 6461 Part 1
BS 6891
BS 8303
In England and Wales, the current edition of the Building Regulations issued by the
Department of the Environment and the Welsh Office
Page 8
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Gas Conversion factor from net to gross efficiency
Natural Gas 0.901
In Scotland, the current edition of the Building Standards (Scotland) Regulations
issued by the Scottish Executive.
In Northern Ireland, the current edition of the Building regulations (Northern Ireland)
issued by the Department of
the Environment for Northern Ireland.
In the republic of Ireland the installation must also conform to the relevant parts of:
a) The current edition of IS 813 “Domestic gas installations”
b) All relevant national and local rules in force.
Where no specific instructions are given, reference should be made to the relevant
British Standard Code of Practice.
4.2 In the United Kingdom, as supplied, the appliance can be installed in the
following
situations: -
4.2.1 To a fireplace complete with surround and hearth as shown in figure 1 and
complying with BS1251 after removal of the fireback and sufficient material behind the
fireback for a debris catchment space. The required fireplace, hearth, debris
catchment area and clearance dimensions are shown in figure 1.
4.2.2 ‘Hole-in-the-wall’ installations.
It is recommended that a
hearth should be installed
as in figure 1.
If a hearth is not fitted, the
fire must be installed so
that the distance from the
base of the fireplace
opening in the wall to the
finished floor level is at
least 85mm.Where there
is no floor covering or
carpet and the floor is of a
type that is likely to be
covered in such a way
then the distance from the
base of the fireplace
opening in the wall to the
finished floor level should
be increased to at least
160mm. The minimum
shelf height will have to be taken from the base of the fireplace opening.
!
To protect from the risk of burns and ignition of clothing a tactile separator shall be
used. The hearth detailed in section 4.9 meets the requirements for a tactile
separator. If this is not used then a 672mm long fender, kerb, horizontal bar, or other
barrier, being fixed not less than 50mm above floor level and positioned 300mm in
Page 9
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 1. Hearth and fireplace opening dimensions
front of the fixing plane of the fire will
meet the requirement.
4.2.3 To a fireplace incorporating a
metal flue box complying with the
constructional requirements of the
current edition of BS715. The
dimensions of the flue box must
conform to those shown in figure 2.
4.2.4 A precast concrete or clay flue
block system conforming to BS1289
or BS EN 1806 with dimensions as
in figure 3 or using a 05654K1
spacer kit. (Installation Instructions
part number 3003095). The current
versions of BS1289 and BS EN
1806 recommend that there should
be an air space or insulation
between the flue blocks and the
plaster because heat transfer may
cause cracking on directly
plastered flues. However, generally
this appliance is suitable for
installations under all
circumstances unless there is a
history of cracking problems.
Remember that faults such as
cracking may be caused by poorly
built and restrictive flues, e.g.
mortar extrusions, too many bends,
flue heights below three metres,
restrictive terminations etc (See
figure 3).
4.2.5 If the fireplace opening is
greater than the acceptable
dimensions given in this guide, do
not use the back of a fire surround
or marble to reduce the opening.
This may cause cracking of the
surround back or marble.
Page 10
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 3. Precast or clay flue block system
dimensions
Figure 2. Metal flue box
Table des matières
Autres manuels Valor Fires Cheminée intérieure
Valor Fires
Valor Fires 347 Mode d’emploi
Valor Fires
Valor Fires 752 Instructions d'utilisation
Valor Fires
Valor Fires 349 Mode d’emploi
Valor Fires
Valor Fires Artura 958 Mode d’emploi
Valor Fires
Valor Fires Artura 958 Instructions d'utilisation
Valor Fires
Valor Fires 752 Instructions d'utilisation
Valor Fires
Valor Fires Carlton Manuel utilisateur
Valor Fires
Valor Fires Artura 958 Mode d’emploi
Valor Fires
Valor Fires 954 Instructions d'utilisation
Valor Fires
Valor Fires 844 Instructions d'utilisation
Valor Fires
Valor Fires 473 Black Beauty Unigas II Mode d’emploi
Valor Fires
Valor Fires 953 Instructions d'utilisation
Valor Fires
Valor Fires 752 Instructions d'utilisation
Valor Fires
Valor Fires 348 Brava Mode d’emploi
Valor Fires
Valor Fires 964 Instructions d'utilisation
Valor Fires
Valor Fires 341 black beauty slimline Mode d’emploi
Valor Fires
Valor Fires 349 Mode d’emploi
Valor Fires
Valor Fires 347 Brava 4 Oxysafe Mode d’emploi
Valor Fires
Valor Fires 339 Heartbeat Oxysafe 2 Instructions d'utilisation
Valor Fires
Valor Fires 761 Mode d’emploi
