VADO SENSORI SmartTouch Manuel utilisateur
WHERE
INSPIRATION
FLOWS
Digital Shower Controller
User Guide
Keep for future reference
Important Information ............................................................................. 3
Digital Controller ..................................................................................... 4
Quick Start ............................................................................................... 5
Shower Operation .................................................................................... 6
- Waking the Shower .......................................................................... 6
- Starting the Shower ......................................................................... 6
- Stopping the Shower ....................................................................... 6
- Cold Setting ..................................................................................... 6
- Adjusting the Showering Temperature .......................................... 7
- Adjusting the Flow Setting .............................................................. 7
- Selecting Outlets ............................................................................. 8
Configuration Mode .. ............................................................................... 9
- Navigating the Configuration Menu ................................................ 9
- Configuration Options .................................................................... 10
Remote Start/Stop Operation .................................................................. 12
Product Care ............................................................................................ 12
Contents
3
This booklet contains all the necessary information for you to
operate and enjoy your Digital Mixer Shower. Please read them
carefully, and keep safe for future reference.
NOTE: The temperature setting displayed on the Digital Control
Panel is measured within the Digital Mixer Processor unit.
Depending on your installation this is not necessarily the
temperature of the water delivered at the shower outlet.
NOTE: When selecting the temperature you want your shower
to be, the display shows the desired temperature. The actual
water temperature delivered will take several seconds to stabilise
depending on your plumbing system.
The Digital Mixer Processor unit MUST only be used with the AC
power supply cable provided. If this supply cable is damaged,
it must be replaced by a VADO engineer or similar qualified
persons to avoid a potential hazard.
This product can be used by children aged 8 years and above and
persons with reduced physical, sensory or mental capabilities
providing they have been given supervision or instruction
concerning use of the product in a safe way and understand
the potential hazards. Children may not play with the product.
Cleaning and user maintenance must not be made by children
without supervision.
Important Information
4
Digital Controller
Temperature
Decrease Flow Decrease
Temperature
Increase Flow Increase
Start/Stop
Flow Volume
Outlet
Control
Outlet
Icon
Single Outlet
Product
Display
Screen
Temperature
Setting
Flow Decrease
Temperature
Decrease
Flow Increase
Start/Stop
Outlet Icon 2
Outlet Flow 2
Flow Volume
Temperature
Increase
Outlet
Control 1
Outlet
Icon 1
Dual Outlet
Product
Display
Screen
Temperature
Setting
5
Quick Start
1 2 3
Wake the shower from
Sleep Mode using the
START/STOP control
Change outlets using the
corresponding OUTLET
controls
NOTE: The available
outlets will vary depending on
the product configuration.
Start and stop the shower
using the START/STOP
control
4
Increase the showering
temperature using the
TEMP + control
Decrease the water
temperature using the
TEMP - control
5
Increase the water
flow using the
FLOW + control
Decrease the water
flow using the
FLOW - control
6
Shower Operation
WAKING THE SHOWER
If the shower has been inactive for a period of 3 minutes, it will return to Sleep Mode, in
order to conserve electricity.
To wake the shower from Sleep Mode, use the START/STOP control
STARTING THE SHOWER
To activate the shower with the default outlet running, use the START/STOP control
Alternatively, to activate the shower with a specified outlet, use the corresponding
OUTLET control NOTE: The available outlets will vary depending on product type.
The shower will start and the temperature display will flash for a short period to
indicate the temperature is being adjusted.
NOTE: If the shower is restarted using the START/STOP control within 3 minutes, it
will restart with the outlet last used.
STOPPING THE SHOWER
To stop the shower, use the START/STOP control
Alternatively, turn all running outlets off using the corresponding OUTLET controls
COLD SETTING
The shower includes a cold setting. When the cold setting is activated, the shower will
stop the hot water supply, allowing only cold water to flow. The cold setting is activated
using the TEMP - control when the showering temperature is set to 32°C.
To cancel the cold setting, use the TEMP + and TEMP - controls to select the
desired showering temperature.
When the cold setting is active, the following icon will be displayed in the temperature
display area:
7
ADJUSTING THE WATER TEMPERATURE
The water temperature can be adjusted between 32°C and
the maximum showering temperature setting (47°C), in
1°C increments.
The showering temperature is adjusted using the
TEMP + and TEMP - controls.
The maximum showering temperature is factory set to 47°C,
but it can be restricted using the maximum temperature
setting in the Configuration Mode (See page 9).
The current temperature setting is shown on the display
screen. When the temperature setting is adjusted,
the display will flash for a short period to indicate the
temperature is being adjusted.
NOTE: When selecting the temperature you want your
shower to be, the display shows the desired temperature.
The actual water temperature delivered will take several
seconds to stabilise depending on your plumbing system.
A default showering temperature can be set in the
Configuration Mode
(See page 9)
. When the default setting
is enabled, the shower will return to that temperature
whenever it wakes from the Sleep Mode. If the default
setting is disabled, the shower will always restart at the
last used temperature setting.
ADJUSTING THE FLOW SETTING
The shower has 10 flow settings.
The flow setting is adjusted using the FLOW + and
FLOW - controls.
The current flow setting is shown on the display screen
A default flow setting can be set in the Configuration Mode
(See page 9)
. When the default setting is enabled, the
shower will return to that pre-set flow whenever it wakes
from the Sleep Mode. If the default setting is disabled, the
shower will always restart at the last used flow setting.
Shower Operation
Current
Temperature
Setting
Current Flow
Setting
8
Shower Operation
SELECTING OUTLETS
The available shower outlets will vary depending on the product configuration,
as shown below.
When starting from Sleep Mode, you can operate the shower with the default
outlet running using the START/STOP control
On subsequent uses, if the shower is restarted using the START/STOP control
within 3 minutes of being stopped, it will restart with the last used outlet running.
The shower will return to the default outlet setting when it returns to the Sleep
Mode after 3 minutes of activity.
NOTE: If the default outlet option is disabled, the shower will always start with
the last used outlet configuration running.
Alternatively, the shower can be started with a specific outlet running using the
corresponding OUTLET control
When the shower is running, the outlets can be turned On and Off using the
corresponding OUTLET control
If all outlets have been selected to Off, the shower will return to the Sleep Mode.
All outlets can be stopped at once using the START/STOP control
Single Outlet
Product
Dual Outlet
Product
Outlet
Control 1
Outlet
Control 1
Outlet
Control 2
Start/Stop Start/Stop
9
Configuration Mode
The Sensori Digital Mixer has many features that can be configured to personalise
your showering experience, using the Configuration Mode.
You can enter the Configuration Mode at any time by holding the TEMP + and
TEMP - controls together for 3 seconds.
NAVIGATE THE CONFIGURATION MENU
When in the configuration mode, a selection arrow is shown next to the
option currently selected.
The selection arrow can be moved up using the FLOW + and moved down
using the FLOW - control.
The current selected option can be chosen by pressing the ACCEPT control /
You can return to the previous menu without updating the setting using the BACK
control /
The Configuration Mode can be exited using the back control / on the main
configuration menu screen.
If no controls are operated for a period of 3 minutes, the shower will
automatically return to Sleep Mode.
The available configuration options varies depending on the products installed
with the Sensori Digital Mixer.
10
Configuration Mode
MAXIMUM SHOWER TEMPERATURE
This limits the outlet water temperature delivered to all
outlets.
It can be adjusted between 32°C and 47°C, in 1°C
increments.
Factory set to 47°C maximum.
MAXIMUM SHOWER TIME
When the maximum showering time is reached, the
shower will automatically return to the Sleep Mode.
It can be set to run for a maximum of 5, 10, 15, 20, 25 or
30 minutes.
Factory set to 30 minutes maximum.
DEFAULT SHOWER TEMPERATURE
When the shower is woken from Sleep Mode, the
temperature setting will return to the default.
If this setting is disabled, the temperature will start at
the last used setting.
It can be set to OFF or set between 32°C and 47°C Max
Shower Temp setting, in 1°C increments.
Factory set to 38°C.
DEFAULT SHOWER FLOW
When the shower is woken from Sleep Mode, the flow
will start on the default setting.
If this setting is disabled, the flow will start at the last
setting used.
It can be set to OFF or set to start on any flow setting
between 1 and 10.
Factory set to 10 as standard.
Table des matières
