VADDIO CLEARVIEW HD-18 Manuel utilisateur
Partner: Vaddio
Model: ClearVIEW HD-18
Device Type: Camera
GENERAL INFORMATION
SIMPLWINDOWS NAME: Vaddio ClearVIEW HD-18 Camera Control v1.0
CATEGORY: Camera
VERSION: v1.0
SUMMARY: This module will control the Vaddio ClearVIEW HD-18 via RS232.
GENERAL NOTES:
This module provides control, real-time feedback from camera, and will also set
various advanced settings. It can have up to 16 presets. Press and hold preset x
input for 2 seconds and the position of camera will save onto that preset number.
There is also a reset mode that when toggled on will erase any preset number when
pressed afterwards.
If multiple units are daisy-chained then it will be necessary to pulse the
Set_Addresses input. This will set the address of each camera.
CRESTRON HARDWARE REQUIRED: C2I-COM, ST-COM, C2-COM-*
SETUP OF CRESTRON HARDWARE:
RS232
Baud:9600
Parity: None
Data Bits: 8
Stop Bits: 1
VENDOR FIRMWARE: Unknown
VENDOR SETUP: DIP switch 4 should be up for the baud rate of 9600.
CABLE DIAGRAM: A DB-9 to RJ-45 adapter is supplied with the camera for RS-232.
CONTROL:
Send_Address_Set D Pulse to set the addresses of the camera.
Power_<On/Off> D Pulse to turn the camera on or off.
Pan_Tilt_* D Press and hold to pan and tilt the camera.
Tilt_Speed A Analog signal to allow the tilt speed to be adjusted. Valid range is 0d to 14d.
Tilt_Speed_<Up/Down> D Pulse to adjust the tilt speed.
Tilt_Speed_Default D Pulse to set the tilt speed to the default value of 7d.
Partner: Vaddio
Model: ClearVIEW HD-18
Device Type: Camera
Pan_Speed A Analog signal to allow the pan speed to be adjusted. Valid range is 0d to 18d.
Pan_Speed_<Up/Down> D Pulse to adjust the pan speed.
Pan_Speed_Default D Pulse to set the pan speed to the default value of 9d.
Zoom_Speed A Analog signal to allow the zoom speed to be adjusted. Valid range is 0d to 7d.
Zoom_<In/Out> D Press and hold to zoom in or out.
Zoom_Speed_<Up/Down> D Pulse to adjust the zoom speed.
Zoom_Speed_Default D Pulse to set the zoom speed to the default value of 4d.
Focus_Speed A Analog signal to allow the focus speed to be adjusted. Valid range is 0d to 7d.
Auto_Focus_<On/Off/Toggle> D Pulse to turn the auto focus on and off.
Focus_<Near/Far> D Press and hold to adjust the focus.
Focus_Speed_<Up/Down> D Pulse to adjust the focus speed.
Focus_Speed_Default D Pulse to set the focus speed to the default value of 4d.
Preset_<1…16> D Pules to recall the preset. Press and hold for 2 seconds to store the current camera
position in the desired preset.
Reset_Mode D Pulse to put the module into preset reset mode. When the Reset_Mode_Is_On
output is high, pulsing a Preset_* input will clear the stored values for that preset.
Auto_White_Balance_<On/Off> D Pulse to turn the auto white balance on and off.
Backlight_<On/Off> D Pulse to turn the backlight on and off.
IR_Recieve_<On/Off/Toggle> D Pulse to turn the IR receiver on and off.
Tally_Light_<On/Off> D Pulse to turn the tally light on and off.
ICR_Cut_Filter_<On/Off> D Pulse to turn the ICR cut filter on and off.
Auto_Exposure_*_Mode D Pulse to set the desired auto exposure mode.
Shutter_<Up/Down> D Pulse to adjust the shutter. Auto Exposure mode must be set to either manual or
shutter priority.
Shutter_Reset D Pulse to set the shutter back to the default setting. Auto Exposure mode must be
set to either manual or shutter priority.
Partner: Vaddio
Model: ClearVIEW HD-18
Device Type: Camera
Aperture_<Up/Down> D Pulse to adjust the aperture.
Aperture_Reset D Pulse to set the aperture back to the default setting.
Gain_<Up/Down> D Pulse to adjust the gain.
Gain_Reset D Pulse to set the gain back to the default setting.
Red_Gain_<Up/Down> D Pulse to adjust the red gain.
Red_Gain_Reset D Pulse to set the red gain back to the default setting.
Blue_Gain_<Up/Down> D Pulse to adjust the blue gain.
Blue_Gain_Reset D Pulse to set the blue gain back to the default setting.
Iris_<Up/Down> D Pulse to adjust the iris.
Iris_Reset D Pulse to set the iris back to the default setting.
Exposure_Compensation_<On/Off> D Pulse to turn exposure compensation on and off.
Exposure_Compensation_<Up/Down> D Pulse to adjust the exposure compensation.
Exposure_Compensation_Reset D Pulse to set the exposure compensation back to the default setting.
IR_Receive_Return_Enable D Pulse to enable. Will send replies what command received from IR commander.
From_Device S Serial data signal to be routed from a 2 way com port.
FEEDBACK:
Power_Is_<On/Off> D High to indicate the current power state.
<Tilt/Pan/Zoom/Focus>_Speed_Gauge A
Analog value indicating the current tilt/pan/zoom/focus speed. To be displayed on a
gauge on a touch panel.
Auto_Focus_Is_<On/Off> D High to indicate the current auto focus state.
Reset_Mode_Is_On D High to indicate that the reset mode is on. Pulsing one of the Preset_<1…16>
while
this is high will reset the values stored for that preset.
Preset_Saved D Will pulse high for two seconds to indicate that the current camera position has
been stored.
Auto_White_Balance_Is_<On/Off> D High to indicate the current auto white balance state.
Partner: Vaddio
Model: ClearVIEW HD-18
Device Type: Camera
Backlight_Is_<On/Off> D High to indicate the current backlight state.
IR_Receive_Is_<On/Off> D High to indicate the current IR receive state.
Tally_Light_Is_<On/Off> D High to indicate the current tally light state.
ICR_Cut_Filter_Is_<On/Off> D High to indicate the current state of the ICR cut filter.
Auto_Exposure_Mode_Is_* D High to indicate the current auto exposure mode.
Exposure_Compensation_Is_<On/Off> D High to indicate the current exposure compensation state.
Error D High to indicate an error was received from the camera.
To_Device S Serial data signal to be routed to a 2 way com port.
TESTING:
OPS USED FOR TESTING: v4.003.0015
SIMPL WINDOWS USED FOR TESTING: 3.01.37
DEVICE DB USED FOR TESTING: 34.00.012.00
CRES DB USED FOR TESTING: 26.00.008.00
SYMBOL LIBRARY USED FOR TESTING: 724
SAMPLE PROGRAM: Vaddio ClearVIEW HD-18 Camera Control v1.0 Demo
REVISION HISTORY: v1.0 – Initial Release
Autres manuels pour CLEARVIEW HD-18
2
Autres manuels VADDIO Caméra de sécurité
VADDIO
VADDIO ZOOMSHOT 20 Manuel utilisateur
VADDIO
VADDIO BU-45H Manuel utilisateur
VADDIO
VADDIO CeilingVIEW 70 PTZ HideAway Manuel utilisateur
VADDIO
VADDIO WallVIEW CCU HD-19 Manuel utilisateur
VADDIO
VADDIO RoboSHOT 20 UHD Manuel utilisateur
VADDIO
VADDIO WallView PRO H900 Manuel utilisateur
VADDIO
VADDIO RoboSHOT 12E USB Manuel utilisateur
VADDIO
VADDIO WallVIEW CCU HD-19 Manuel utilisateur
VADDIO
VADDIO RoboSHOT 12 HDMI Manuel utilisateur
VADDIO
VADDIO WallVIEW HD-USB PRO System Manuel utilisateur
VADDIO
VADDIO RoboSHOT HDBT Series Manuel utilisateur
VADDIO
VADDIO CLEARVIEW HD-20 Manuel utilisateur
VADDIO
VADDIO ZOOMSHOT WALLVIEW SR 999-6918-001 Manuel utilisateur
VADDIO
VADDIO WallVIEW D80 PTZ Manuel utilisateur
VADDIO
VADDIO Domeview Manuel utilisateur
VADDIO
VADDIO WallVIEW 70 PTZ Manuel d'installation et d'exploitation
VADDIO
VADDIO RoboSHOT HDMI Series Manuel utilisateur
VADDIO
VADDIO RoboSHOT 12 Manuel utilisateur
VADDIO
VADDIO WALLVIEW CCU HE100 Manuel utilisateur
VADDIO
VADDIO ZOOMSHOT 20 Manuel utilisateur
