Vacmaster VQ1530SFDC Manuel utilisateur

VQ1530SFDC

1500W30L

IPX4

www.cleva-europe.com

MADE IN P.R.C

21 22 23 24 25 26

15 16 17 18 19 20

TABLE OF CONTENTS

SECTION PAGE

Safety Information ......................................................................................................................... 5

Unpacking and Checking Carton Contents ................................................................................... 7

Assembly....................................................................................................................................... 7

Operation ...................................................................................................................................... 8

Maintenance.................................................................................................................................. 9

Troubleshooting........................................................................................................................... 10

Technical Data..............................................................................................................................11

Recycling and Disposal ................................................................................................................11

Plug/Fuse Replacement (UK & Ireland Only)...............................................................................11

Thank you for purchasing this Vacmaster® wet and dry vacuum cleaner. Feel condent that with

Vacmaster®you are obtaining a high quality product engineered for optimal performance. This

vacuum cleaner is suitable for use with both liquids and dry materials.

FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS.

SAFETY INFORMATION

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE

USING THIS VACUUM CLEANER.

When using the equipment, a few safety precautions must be

observed to avoid injuries and damage. Please read the complete

operating manual with due care. Keep this manual in a safe

place so that the information is always available. If you give

the equipment to any other person, give them these operating

instructions as well. We cannot accept any liability for damage or

accidents which arise due to a failure to follow these instructions

and the safety information.

• Never leave the appliance switched on unattended, if you leave

the work area, switch the appliance off or unplug it from the

power supply.

• Do not vacuum or use this Wet and Dry Vacuum cleaner near

ammable liquids, gases or explosive vapours like gasoline or

other fuels, lighter uids, cleaners, oil-based paints, natural gas,

hydrogen, or explosive dusts like coal dust, magnesium dust,

grain dust or gun power. Sparks inside the motor can ignite

ammable vapours or dust.

• This vacuum cleaner is not suitable for the vacuuming of

asbestos or asbestos dust.

• Do not vacuum anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

• Ensure the hose and connections are always pointed away from

the users face, hair, ears and eyes during operation and never

direct the nozzle towards persons or animals.

• Clear the working area of any items or precessions that you do

not wish to be vacuumed before operation.

• Keep cord away from heated surfaces.

• Do not expose to rain. Store indoors.

• Do not unplug by pulling on the cord. To unplug, grasp the plug,

not the cord.

• Do not use with damaged cord, plug or other parts.

• Do not pull or carry by cord, use cord as handle, close a door on

cord, or pull cord around sharp edges or corners.

• Do not handle the plug or vacuum cleaner with wet hands.

• To reduce the risk of health hazards from vapours or dusts, do

not vacuum toxic materials.

• Frequently check that the oat valve positioned underneath the

motor is able to move freely.

• Do not use or store near hazardous materials.

• Do not use this vacuum cleaner with a torn lter or without the

lter installed.

• Do not allow to be used as a toy. Close attention is necessary

when used by or near children.

• To reduce the risk of injury from accidental starting, unplug

power cord before changing or cleaning lter.

• Do not leave vacuum cleaner unattended when plugged in.

Unplug from power supply when not in use and before carrying

out maintenance.

• Turn off Wet and Dry Vacuum cleaner before unplugging.

• Do not cover the ventilation openings. Do not vacuum with any

ventilation openings blocked; keep free of dust, lint, hair or

anything that may reduce air ow.

• Keep hair, loose clothing, ngers, all parts of body away from

openings and moving parts.

• If the supply cord is damaged, it must be replaced by the

manufacturer, a qualied service agent or similarly qualied

persons in order to avoid a hazard.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

• Children should be supervised to ensure that they do not play

with the appliance.

• For additional protection: It is recommended that this vacuum

cleaner can be used in conjunction with residual current device

(RCD) with a rated residual current of 30mA or less.

• Always unplug the appliance after use and before cleaning or

changing the lters or accessories.

When using as blower:

• Direct air discharge only at work area.

• Do not use Wet/Dry Vacuum as a sprayer.

• Do not direct air at bystanders.

• Keep children away when blowing.

• Wear safety goggles.

UNPACKING AND CHECKING CARTON

CONTENTS

1 Carry Handle 10 Caster 19 Power Tool Hose Adaptor

2 On/Off Switch 11 Blowing Port 20 Round Dust Brush

3Power Take-off Socket 12 Power Cord Storage Hooks 21 Cartridge Filter (pre-installed)

4 Suction Port 13 Anti-static Chain 22 Filter Retainer (pre-installed)

5 Container 14 Hose 23 Dust Bag

6 Drainage Port 15 Extension Wand (x2) 24 Foam Filter

7 Power Head 16 Crevice Tool 25 Screw (x6)

8 Accessory Storage 17 Handle with Air Flow Regulation 26 Instruction Manual

9 Latch 18 Floor Nozzle

ASSEMBLY

NOTE: A Phillips screwdriver is required.

1) Remove all the contents from inside of the vacuum cleaner container.

2) Attach the carry handle into the slots located on the top of the power head (Fig. 1).

3) Turn the container upside down and insert the feet with casters into the slots and apply

pressure until they click into place. Secure them with supplied screws (Fig. 2).

4) Your vacuum cleaner comes ready for dry vacuum cleaning with the cartridge lter pre-installed.

If the cartridge lter is not installed, refer to page 8.

5) Optionally, for improved dust ltration, fully t the dust bag ange onto the inlet stub (Fig. 3).

6) For wet vacuuming, replace the cartridge lter with the foam lter supplied. Do not use a dust

bag when wet vacuuming. If the foam lter is not installed, refer to page 9.

7) Secure the power head back on the container, using the 2 side latches. Insert the locking end

of the hose into the suction port of the container (Fig. 4).

8) Choose the desired accessories and/or extension wands and push t onto the hose nozzle.

OPERATION

1. Switching On/Off

Connect the mains plug to a suitable a power outlet.

Position Status

I on

O off

II automatic synchronized start-up

2. Power Tool Take-Off Operation (Fig. 5)

WARNING: Always check the maximum wattage compatibility of the power tool take off

socket against the desired power tool before connecting to prevent overloading.

1) Connect the power cable of your power tool to the power take-off socket.

2) If applicable, connect the vacuum suction hose to the dust extractor connector on your tool with

the supplied adaptor.

3) Switch the vacuum cleaner to position II, as described in Switching ON/OFF. The moment you

switch on the power tool, the vacuum cleaner will also switch on. Once the electrical appliance

has been switched off, the vacuum cleaner switches off following a time lapse (around 5

second) to allow the suction tube to be emptied.

3. Dry & Wet Vacuum Operation

WARNING: ENSURE YOU READ, UNDERSTAND AND APPLY SECTION ENTITLED

‘SAFETY INFORMATION’.

1) Verify that the correct lter is installed for wet or dry vacuuming and the container latches are

secured.

2) Secure the locking end of the hose into the vacuum suction port.

3) Push the desired accessories onto the hose nozzle. The air ow regulation allows you to change

vacuum cleaner suction. For best cleaning results, fully close the air ow regulation (Fig. 6).

4) Plug the power cord into a power outlet.

5) Turn on the motor by assigning the switch to the “I” ON position.

6) Once you have completed vacuuming, switch to the “O” OFF position and unplug the power

cord from the power.

For Dry Vacuuming:

WARNING: BEFORE INSTALLING, REMOVING OR CLEANING THE VACUUM

CLEANER FILTER, ENSURE THAT THE POWER CORD IS UNPLUGGED AND

SWITCHED OFF.

1) To prepare your vacuum cleaner for dry vacuuming, install the cartridge lter over the lter cage

with the at end of the lter towards the vacuum power head. Carefully push lter until it sits

ush forming a tight seal.

2) Place the lter retainer cap on top of cartridge lter over the raised lip and tighten the retainer

lock clockwise to secure against the internal lter cage (Fig. 7).

3) Optionally, fully t the dust bag ange onto the inlet stub. The Vacuum cleaner can we be used

with or without dust bags.

IMPORTANT: Check the lter regular for optimal performance. An old or blocked lter will reduce

suction performance.

For Wet Vacuuming:

1) To prepare your vacuum cleaner for wet vacuuming, remove the retainer cover and the dry use

cartridge lter.

2) Carefully install the supplied foam lter over the internal lter cage, making sure the whole cage

is covered (Fig. 8).

WARNING:

DO NOT USE THE CARTRIDGE FILTER FOR WET VACUUMING.

DO NOT USE A DUST COLLECTION BAG FOR WET VACUUMING.

IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely;

leave a gap at the tip of the nozzle to allow air inow. The machine is tted with a oat valve that

stops the suction action when the container reaches its maximum capacity. You will notice an

increase in motor noise. When this happens, turn off the machine, disconnect from power supply,

and drain the liquid. To continue vacuuming, replace the drainage cap. After wet vacuuming, empty

the container, clean and dry inside before storage.

4. Blower Operation

WARNING: KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS.

WARNING: WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE

INHALED.

1) Make sure the container and any collected waste is emptied before using as a blower. This also

includes removal of the dust bag.

2) Insert the locking end of the hose into the blowing port on the rear of the power head (Fig. 9).

3) Turn on the motor on by turning the switch to the ‘I’ ON position.

MAINTENANCE

WARNING: REMOVE THE POWERCORD FROM THE POWER SUPPLY BEFORE

CARRYING OUT ANY MAINTENANCE.

1) Keep all safety devices, air vents and the motor housing free of dirt and dust. Use a soft, dry

brush to clean the equipment regularly.

2) Clear all dirt or debris from the collection tank after each use. Allow to dry before replacing the

power head. Do not use cleaning agents or solvents; these may damage the appliance.

3) Check the hose, attachments, and power cord to verify that they have not been damaged or

any debris is trapped and blocking airow.

1. Cleaning Cartridge Filter

Remove the lter and clean by gently tapping or brushing off dirt. For optimal performance it is

recommended to replace the old lter with a new lter regularly.

2. Cleaning Foam Filter

Remove the foam lter and use a mild soap and water solution to wash and rinse with clean water

(Fig. 10). Allow lter to air dry before installing and using again.

TROUBLESHOOTING

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE

TROUBLESHOOTING.

Cleaning Performance

Vacmaster vacuum cleaners are tested for endurance. If your motor is operating, then the most

likely cause for a loss in suction is a blockage or an opening in the vacuum.

To maintain a high cleaning performance from your machine, it is important to replace or clean

cartridge lters as necessary. Replace full dust bags to prevent performance drops. A performance

drop with clean lters can only be caused by a blockage in the tools or the hose.

PROBLEM POSSIBLE CAUSE SOLUTION

The appliance does

not work.

No power. Check the power supply and fuse.

Functional fault in the power

cord, switch, or motor.

Have the damaged part checked by

qualied personnel or contact the after

sales helpline.

Dust is escaping from

the motor cover.

The cartridge lter is missing

or damaged. Put in a cartridge lter or replace it.

Misuse the cartridge lter

when wet vacuuming, causing

the damage of cartridge lter

Replace the damaged cartridge lter

with a new one when dry vacuuming.

Misuse the foam lter when

dry vacuuming.

Replace the foam lter with the

cartridge lter.

Power tool take-off

socket does not work.

Power tool wattage is not

compatible with the power

take-off socket.

Check the wattage is compatible with

the power tool take-off socket.

Incorrect operating mode

selected.

Ensure the switch is moved into

position II.

Low suction power

and high operating

noise / vibrations.

Dust bag is full. Replace the dust bag.

Suction nozzle, hose, or tank

inlet is blocked.

Check the suction nozzle, hose, and

tank inlet for obstructions.

Cartridge lter is blocked. Remove the cartridge lter and clean.

Float valve has closed.

Empty the container of any liquid

waste and ensure the oat value

located underneath the lter is able to

move freely.

Autres manuels pour VQ1530SFDC

Table des matières

Autres manuels Vacmaster Aspirateur

Vacmaster

Vacmaster VQ607SFD Manuel utilisateur

Vacmaster

Vacmaster VK811PH Manuel utilisateur

Vacmaster

Vacmaster VK1638SWC Manuel utilisateur

Vacmaster

Vacmaster VOM205P Manuel utilisateur

Vacmaster

Vacmaster EATC608S Manuel utilisateur

Vacmaster

Vacmaster VOM205P Manuel utilisateur

Vacmaster

Vacmaster VZA0708P Manuel utilisateur

Vacmaster

Vacmaster VF408 Manuel utilisateur

Vacmaster

Vacmaster VBV809PF Manuel utilisateur

Vacmaster

Vacmaster VOC507PF Manuel utilisateur

Vacmaster

Vacmaster VOC1218PF Manuel utilisateur

Vacmaster

Vacmaster VWM510 Manuel utilisateur

Vacmaster

Vacmaster VQ1220PF Manuel utilisateur

Vacmaster

Vacmaster VK1638SWC Manuel utilisateur

Vacmaster

Vacmaster VMVK1520SIWC Manuel utilisateur

Vacmaster

Vacmaster VF408 Manuel utilisateur

Vacmaster

Vacmaster VJF607PF 1101 Manuel utilisateur

Vacmaster

Vacmaster VJH1211PF 0204 Manuel utilisateur

Vacmaster

Vacmaster VK1650SWD 950091 Manuel utilisateur

Vacmaster

Vacmaster VZA306P 1101 Manuel utilisateur

Vacmaster

Vacmaster VSD1801 Manuel utilisateur

Vacmaster

Vacmaster VK809PWR 0201 Manuel utilisateur

Vacmaster

Vacmaster VJF912PF 0201 Manuel utilisateur

Vacmaster

Vacmaster MVOA407S Manuel utilisateur

Manuels Aspirateur populaires d'autres marques

Bissell

Bissell LittleGreen Proheat 1425 Series Manuel utilisateur

Panasonic

Panasonic MC-YL637S147-AE Manuel utilisateur

NEFF

NEFF N17XH10 0 Series Manuel utilisateur

LG A9 Series Manuel utilisateur

Oreck

Oreck Cordless Captura BK51700 Series Manuel utilisateur

Kogan

Kogan KAVACROBVWA Manuel utilisateur

Kränzle

Kränzle VENTOS 50 ID Guide de l'utilisateur

EVVO

EVVO Ai35 Manuel utilisateur

DeWalt

DeWalt DWH200D Manuel utilisateur

Pontec

Pontec Pondomatic Vacuum Cleaner Manuel utilisateur

Cleanmaxx

Cleanmaxx PC-P007E Manuel utilisateur

Exido

Exido 240-114 Manuel utilisateur

RIDGID

RIDGID WD1685AU0 Manuel utilisateur

Ezviz

Ezviz RE4P Manuel utilisateur

STG global

STG global TANVAC HDV3000 Manuel utilisateur

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manuel utilisateur

Factory

Factory M3340 Manuel utilisateur

Shop-Vac

Shop-Vac VN92 SERIES Manuel utilisateur