V-TAC VT-5188 Manuel utilisateur

INSTALLATION INSTRUCTION

4CH WIRELESS SECURITY SYSTEM

No. Name Quantity No. Name Quantity

1 Wireless NVR 1 7 Quick Operation Guide 1

2 Wireless IPC 4/8 8 Screw for hard disk 1

3 IP Cable(1M) for

matching code 1 9 Screw for IPC 4/8

4 USB Mouse 1 10 Power supply for NVR 1

Antenna for NVR

(black) 2 11 Power supply for IPC 4/8

6 Antenna for IPC

(white)

4/8 12 IPC installation sticker 4/8

INTRODUCTION

PACKING LIST

Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these

instructions carefully before starting the installing and keep this manual handy for future reference. If

you have any another query, please contact our dealer or local vendor from whom you have

purchased the product. They are trained and ready to serve you at the best.

HARDWARE

1. Statement

Thank you for using our product, please contact us if you have any question.

This guide is for Wireless NVR Kit.

Content may be modified and updated based on new function. The function of the actual products maybe a little

different from the guide, please operate it referring to actual products.

2. Attention

①Do not install the wireless NVR in humid and dusty environment.

②Put the wireless NVR in drafty environment in case of ventilation port being blocked.

③Check the power supply to avoid damage because of voltage mismatch.

④Make sure the wireless NVR working within suitable temperature and humidity environment.

⑤Please install the wireless NVR horizontally, and avoid vibration.

⑥Short circuit may occur when dust become wet on circuit board. Please clean the dust

on circuit board, connectors, and NVR case.

⑦Explosion may happen because of improper replacement of battery, do not replace it by yourself;

If you need, make sure it is the same type of battery. And do not open or repair it.

⑧Please use suitable and professional hard disk to ensure continues and stable recording.

⑨Lightning protection is needed when device is connected to communication cables.

Ethernet cable which comes form outside, connecting to the wireless NVR directly is forbidden.

3. Open and Check

Open the package when received, put the products and spare part in suitable place, check them based on packing

list. If there is anything broken or missing, please contact to us as soon as possible.

Hardware

Attention:

Please use suitable and professional hard disk; Do shut off power before installation.

Step 1:Put the NVR on table horizontally, loosen 4pcs M3*6 screws,as picture1-1 shows;

Step 2: Push the cover to the back direction , connect data cable and power supply cable to the ports on

hard disk separately, as picture 1-2 shows.

Picture1-1

3 4

1 2

Picture1-2

1.Hardware Disk Installation

Step 3: Match the hole between hard disk and NVR case, as picture 1-3 shows;

Step 4: Put NVR on table sideways, fix hard disk with 4pcs BM6#-32*6 screws, as picture 1-4 shows;

Picture1-3 Picture 1-4

Picture1-5

2.INTERFACE

①Audio output Antenna

②VGA output

③HD- output

④Network port

⑤USB interface

⑥Power supply : DC12V

Attention: The IPC should be installed on the wall with suitable thickness, which can sustain 4 times weight of IPC& spare part.

STEPS

① Hole location sticker: put the sticker on the wall, punch with 5mm drill in the marked areas, make sure the deep of hole is over

30mm at least.Then punch expansion screws in hole. As Picture 4-1 shows.

② Fixing IPC: The structure of wireless IPC is integrated, please use 3pcs PA4 screws to fix IPC on the wall. As picture 4-2 shows.

③ Bracket adjustment: loosen the screw on IPC, the range of angle for adjusting is showed on picture below,adjust the IPC to

suitable direction, then tighten the screws. As picture 4-3 shows.

3.LOG IN/LOG OUT

4.INSTALLATION OF WIRELESS PC

Please make sure the voltage of power supply is matched with wireless NVR, and ground connection work well in socket. When

power supply connected, indication lamp 【POWER】turn on, it means system runs smoothly.

Picture4-1 Picture4-2 Picture4-3

5.WIFI NVR KIT DIAGRAM

When there comes to no/stuck image because the barrier weaken the signal, user can replace the antenna with extension cable,

to bypass the obstacles, user can place it in a better signal position of NVR.

The shape of wireless NVR signal coverage is a ball, antenna is located in the center. Signal is strong around antenna, and weak in the dent area of the

2 antennas. Based on the signal spreading ways, please make the wireless IPC keeping parallel or tangent with wireless NVR, which ensure stable

signal transmission and better picture quality.

6.PLACEMENT OF WIRELESS PC

Right placement Wrong placement

6.EXTENDING SIGNAL COVERAGE RANGE BY ANTEENNA EXTENSION CABLE

SOFTWARE OPERATION

① Right-click on main interface, select【IP Camera】-【Add】-【Match Code】

② If just match one device, please connect IPC and NVR with IP cable in WAN port. For multiple matching, please connect IPC to switch, and connect

NVR to switch in WAN port.

③ Click 【Match Code】, system will match the code between IPC and NVR.

④ When finished code matching, click 【Search】, then select 【Add All】. User also can click to add it and view picture

Attention: The code has been matched before output, user no need to add the IPC again, picture will be shown automatically when power on.

For code matching, please follow the steps above, and delete the useless channels.

1. Code Matching & IPC Adding

① Check the hard disk. Right-click→【Menu】→【Disk】. Make sure hard disk is connected to NVR and run normally.

Attention : please format hard disk, it can come into using after showing capability

② Timing and alarm record: 【Menu】→【Record】→【Record Time】→ choose type→【apply】.

Attention:Wi-FiNVRsystemisdefaultsetting24hmanualrecord,andalso,【AllDay】/【Daytime】【Night】/【Custom】areforoptional

③ ManualRecord:Right-click→【ManualRecord】→chooserecordingchannel→【Save】(Actually,theWi-FiNVRsystemhavedefaultset

24threcording)

2. Record & Playback

④ Playback: Right-click →【Playback】→ choose channel and date → double click date to query→ double click timeline to check record.

Insert U disk to NVR USB port→ Right-click→【Menu】→【Record】→【Backup】→ choose time, channel and type→【Query】→

select target file →【Start Backup】(some wireless NVR will just 1 USB port, please pull out mouse and insert backup device in 45S after click

【Start Backup】.

Attention: If target file can not be searched out, please click【Empty】→【Add】. Please remove the files which is no need before backup.

Ensure insert device( like USB) in 45S, as system reserved searching time for it is 45S.

3.Backup

① Right-click→【Menu】→【Alarm】→【Motion Detect】→ choose target channel→ click 【Enable】→

Set Sensitivity & Area & Time & Alarm mode→ Choose Channels for recording when Motion Detection Alarm is

triggered→【Apply】.

② Back to【Record】interface→【Record time】→ 【Custom】→ set record period of target channel→ click

【Motion】→【Apply】. User can also set shelter and linkage alarm in the same way above.

4.Motion Detection Record

【Menu】→【WireNetwork】

InLAN,thereare2waysforwirelessNVRtoconnecttoInternet.

Manualsetting:FillinIPaddress,DNSdata,andclick【Apply】.

DHCP:openDHCP,devicewillconnecttoInternetautomatically,noneeddatasetting.

Ifuserdoesnʼtfamiliaraboutthenetworkenvironment,preferuseDHCPﬁrst,please.

Bridge

Bridging function: to expand the coverage area of wireless signal.

IPC in further area can connect to near IPC via Wi-Fi signal and connect to NVR finally. It could extend transmission

distance for complicated installation scenes.

① Steps: 【Menu】→【Channel】→【Bridge】

5. Internet Connection

Table des matières

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur