urmet domus 1083/12 Manuel utilisateur
1083/12 -1083/15 -1083/16
Configuration guide
System Type D
Contents
Introduction
How to use this Configuration Guide
Menu structure
Configuration procedure
Programming proximity access keys
Programming door open codes
Appendix
Contents
Introduction
How to use this Configuration Guide
Menu structure
Configuration procedure
Programming proximity access keys
Programming door open codes
Appendix
Contents
Introduction
How to use this Configuration Guide
Menu structure
Configuration procedure
Programming proximity access keys
Programming door open codes
Appendix
How to use this Configuration Guide
Configuration procedure
Programming proximity access keys
Programming door open codes
How to use this Configuration Guide
Configuration procedure
Programming proximity access keys
Programming door open codes
How to use this Configuration Guide
Programming proximity access keys
Page 1
Page 2
Page
Page
Page
Page
Page
Page 1
Page 2
Page
3
Page
4
Page
21
Page
22
Page
23
Introduction
1083/20 1083/20 1083/50 1083/501083/20
1083/20 1083/75
1083/50
This programming guide is intended specifically for a particular type of system –System Type D
Block A….Block 1….Block ? Block B….Block 2….Block ? Block Z….Block 32….Block ?
System Type D–
One (or up to a maximum of four) ‘Primary’ entry panels i.e. panels which call all apartments in the system.
One or more blocks (maximum of 32) each with one or two ‘Secondary’ panels which only call apartments within
that block
The apartment numbers within a block can be in any range for example 1 to 127 or 400 to 450 or 1001 to 1050
‘
Primary’
entry panels
(call all apartments)
‘Secondary’ entry panels
(call only apartments within
a specific block)
Page 1
How to use this Configuration Guide
Each entry panel in the system must be individually programmed.
Primary entry panels and Secondary entry panels are programmed using the same method but have a number of
different settings.
Whether a panel is a Primary panel or a Secondary panel depends not only on its configuration but also on its
connection within the system. Refer to the connection diagram supplied with the equipment or the diagram on
Page 1 to determine whether the panel you are configuring is Primary or Secondary.
It is not important whether Primary or Secondary entry panels are programmed first, in fact a system can be
installed with only Secondary entry panels and Primary entry panels can be added later and vice versa.
In this guide, configuration steps that are specific to Primary panels are covered on Page 6 and steps specific to
Secondary panels are covered on Page 7.
Note –When configuring the entry panel it is necessary to pass through each
step and arrive back at the top level menu for information to be saved.
Top level menu
Page 2
Menu Structure
LANGUAGE
CONFIGURATION
NAMES
DOOR OPENER
KEYS
RESET
SIMPLIFIED GUI
MODULE TYPE
MULTIRISE
ID PRIMARY MODULE
CODE TYPE
BUSY TIME
STOPABLE
DOOR LOCK 1 RELEASE TIME
DOOR LOCK 1
DOOR LOCK 2 RELEASE TIME
DOOR LOCK 2
PASSWORD
LCD BACKLIGHT
BUTTON SOUND
MULTITOUCH CALL
WELCOME MESSAGE
TIME ZONE
DATE AND TIME
DAY
POSTMAN
VOCAL SYNTHESIS
SWITCHBOARD
NEW
MODIFY
DELETE
DELETE ALL
NEW
MODIFY
DELETE
DELETE ALL
NEW
MODIFY
DELETE
Page 3
Configuration procedure
When the unit is first powered the screen is as follows –
On the entry panel keypad press 99999 and you will see this screen –
Enter 1000 (the default password) then press
Use the and buttons to select LINGUA and press
Use the and buttons to select ENGLISH UK and press
ENGLISH UK
Page 4
You see this screen –
Press the button to select CONFIGURATION then press
Use the or buttons to select YES and press
CONFIGURATION
LANGUAGE
Page 5
Primary entry panels only
PRIMARY
SECOND
ARY
Use the or buttons to select PRIMARY and press
FROM: 0
TO: 3
The RANGE OF BLOCKS depends on the number of blocks in the installation. If there
are four blocks for example, then the range is from 0to 3.
Press to move to the TO entry.
Press and then enter the last block number. 3 In this example.
Press
In a system with only one primary entry panel the ID is always 0.
In this case just press .
In a system with two, three or four Primary panels, each must have a different ID.
To change the panel ID to 1 for example,just press then press
The ID of the panel is determined by where it is connected in the system.
You must refer to the connection diagram of your system for the ID of each panel.
Page 6
Secondary entry panels only
Page 7
Use the or buttons to select SECONDARY and press
The RISE NUMBER is the Block Number between 0 and 31 or more specifically;
it is the address of the 1083/50 Riser Distributor to which the secondary panel is
connected.
For example if the secondary entry panel being programmed, is connected to a
1083/50 with the address then the RISE NUMBER is 2.
5
4
1
3
6
ON
2
Each block can have a maximum of two secondary panels, therefore the address of
the panel being programmed can be either 0or 1.
To change the panel ID to 1 just press then press
It is suggested to keep the default setting by pressing
It is suggested to keep the default setting by pressing
DOOR LOCK 1 RELEASE TIME adjusts the voltage free relay (C NO NC) time
and also the solid state lock release output (SE+ SE-) time.
For example for a time of 10 seconds press 1 0
Choosing FREE means that the door can be opened by the monitor or handset at
any time without the monitor or handset being called.
Choosing SECRET means that the monitor or handset must be called before it can
open the door.
Use the or buttons to make a selection then press
Page 8
Autres manuels pour 1083/12
3
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels urmet domus Panneau de contrôle
urmet domus
urmet domus 925 Manuel utilisateur
urmet domus
urmet domus 1067/032A Manuel utilisateur
urmet domus
urmet domus 1067 Series Manuel utilisateur
urmet domus
urmet domus 1067 Series Manuel du propriétaire
urmet domus
urmet domus Elkron C420 Manuel utilisateur
urmet domus
urmet domus 2 VOICE mikra Manuel utilisateur
urmet domus
urmet domus 2VOICE MIKRA2 1784 Guide de démarrage rapide
urmet domus
urmet domus 1061/004 Instructions de montage
urmet domus
urmet domus ELKRON DK500M-P Manuel utilisateur
urmet domus
urmet domus 1067/032 Manuel du propriétaire
