UNIVIEW DC4300 Series Manuel utilisateur

DC4300 Series

Video Decoders

Quick Guide

Manual Version: V1.03

Notice

The information in this manual is subject to change without notice.

Every effort has been made in the preparation of this manual to ensure

accuracy of the contents, but all statements, information, and

recommendations in this manual do not constitute the warranty of any

kind, express or implied.

Environmental Protection

This product has been designed to comply with the requirements on

environmental protection. For the proper storage, use and disposal of

this product, national laws and regulations must be observed.

Preface

Audience

This manual is intended for:

Surveillance system planners

Field technical support and servicing engineers

Software installation, configuration, and servicing administrators

Product users

Safety and Compliance Information

Conventions Used Symbol

The symbols in this chapter are shown in the following table. They are

used to remind the reader of the safety precautions during equipment

installation and maintenance.

Safety

Symbol

Description

Generic alarm symbol: To suggest a general safety concern.

ESD protection symbol: To suggest electrostatic-sensitive

equipment.

Electric shock symbol: To suggest a danger of high voltage.

Safety Information

WARNING!

Installation and removal of the unit and its accessories must be carried

out by qualified personnel. You must read all of the Safety Instructions

supplied with your equipment before installation and operation.

Warnings:

If the product does not work properly, please contact your dealer

or the nearest service center. (We shall not assume any

responsibility for problems caused by unauthorized repair or

maintenance.)

To reduce the risk of fire or electrical shock, do not expose this

product to rain or moisture.

This installation should be made by a qualified service person and

should conform to all the local codes.

Please install blackouts equipment into the power supply circuit for

convenient supply interruption.

The separate grounding terminal must be permanently connected

to earth.

For AC supplied model: The plug-socket combination must be

accessible at all times as it serves as the main disconnecting device.

Before the power cable is installed or removed, the power must be

turned off.

To avoid heat accumulation, good ventilation is required for a

proper operating environment.

Improper use or replacement of the battery may result in hazard of

explosion. Please use the manufacturer recommended battery

type.

Caution: Fiber optic ports –optical safety.

Never look at the transmit laser while the power is on. Never look

directly at the fiber ports and the fiber cable ends when they are

powered on.

Caution: Use of controls or adjustments to the performance or

procedures other than those specified herein may result in hazardous

laser emissions.

Regulatory Compliance

FCC Part 15

This equipment has been tested and found to comply with the limits for

digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his

own expense.

This product complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

LVD/EMC Directive

This product complies with the European Low Voltage Directive

2006/95/EC and EMC Directive 2004/108/EC.

WEEE Directive–2002/96/EC

The product this manual refers to is covered by the Waste Electrical &

Electronic Equipment (WEEE) Directive and must be disposed of in a

responsible manner.

Contents

1 Overview..............................................................................................1

Appearance ...................................................................................................1

LEDs...............................................................................................................2

Main Ports.....................................................................................................4

2 Installing the Device .............................................................................7

Preparation ...................................................................................................7

Checking the Device Package ...............................................................7

Checking the Installation Environment.................................................7

Cable Requirements .............................................................................7

Installation Flow Chart ................................................................................10

Installing the Device in a Rack.....................................................................11

Preparing for the Installation..............................................................11

Installing the Mounting Brackets........................................................11

Installing the Device in the Rack.........................................................12

Verifying the Installation ....................................................................13

Installing the Device on a Workbench ........................................................14

Preparation for the Installation ..........................................................14

Installation Procedure ........................................................................14

Connecting Cables.......................................................................................14

Cabling Requirements ........................................................................14

Example for Connecting Cables ..........................................................15

Connecting the Ground Wire..............................................................17

Connecting the Audio Cables and Alarm Cables.................................18

Connecting video cables .....................................................................20

Connecting Network Cables ...............................................................21

Connecting the AC Power Cord ..........................................................21

Connecting RS-232 Serial Cables ........................................................22

Connecting a Third-Party Device ........................................................22

Verifying the Installation.............................................................................23

Starting Up the Device ................................................................................23

3 Logging In to and Out of the Device .....................................................23

4 Technical Specifications ......................................................................24

1 Overview

NOTE!

This manual describes the device hardware information and installation

procedure, and guides you through logging into the Web interface.

This series video decoders (referred to as device in this manual) are new

generation HD network video decoder terminals. The device is designed

for remote video surveillance and can be widely applied in various

real-time surveillance applications for monitoring audios and videos

remotely in real time.

For information about the technical specifications of the device, see

Technical Specifications.

Appearance

Figure 1-1 Front view

1: RUN LED

2: NET1

LED

3: DEC

LED

4: Alarm

LED

5: NET2 LED

123

Figure 1-2 Rear view

1: VGA IN port

2: DVI-I OUT port

3: RS-485 port (RJ-45)

4: ACT LED

5: LINK LED

6: AUDIO OUT port

7: ALM IN port

8: DVI IN port

9: RS-232 port (RJ-45)

10: Two Ethernet

copper ports

11: LINE port

12: ALM OUT port

13: Grounding screw

14: AC power input

15: Power switch

LEDs

Table 1-1 LED description

LED

Status

Description

Running LED

Flashing green

The device is starting

up.

On (Green)

The device is

operating.

Off

The device is shut

down.

Alarm LED

On (Red)

At least one alarm, for

example, temperature

alarm, is present.

Off

No alarm is present.

LINK LED for Ethernet

copper port 1 (NET1)

On (Green)

A link to the Ethernet

copper port 1 is

present.

Off

No link to the

Ethernet copper port

1 is present.

2 7

811

1 5 6

3 4

10 12 14 15

LED

Status

Description

LINK LED for Ethernet

copper port 2 (NET2)

On (Green)

A link to the Ethernet

copper port 2 is

present.

Off

No link to the

Ethernet copper port

2 is present.

Decoding LED (DEC)

Flashing green

The device is

displaying video.

Off

The device stops

displaying video.

Active LED (ACT)

Flashing yellow

Data is being

transmitted or

received.

Off

No data is being

transmitted or

received.

Link LED

On (Green)

A link is present.

Off

No link is present.

Table des matières

Autres manuels UNIVIEW Convertisseur de média

UNIVIEW

UNIVIEW ADU87XX-E Series Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur