UNISENSE UniAmp fx-6 Manuel utilisateur

Unisense UniAmp Multichannel Systems

User Manual

UNIAMP MULTICHANNEL SYSTEM MANUAL

Version 1.1, August 2020

 

 
Table of Contents 
Scope of the manual .......................................................................................................................3 
Warranty and liability .....................................................................................................................3 
1 Repair or adjustment..............................................................................................................3 
Support, ordering, and contact information...................................................................................3 
Overview.........................................................................................................................................3 
Operating and setup conditions .....................................................................................................4 
Installation and setup of UniAmp and software.............................................................................4 
1 Installation of the SensorTrace Suite software.......................................................................5 
2 Connect the UniAmp to the PC...............................................................................................5 
Getting started................................................................................................................................6 
1 Connecting sensors with automatic settings..........................................................................6 
2 Manually setting the Pre-amplification ..................................................................................6 
3 Manually setting the sensor polarization ...............................................................................6 
4 Adjusting the offset.................................................................................................................7 
5 Setting STOX sensor parameters ............................................................................................7 
6 Polarizing amperometric sensors without a PC connected....................................................8 
Sensor connections and compatibility............................................................................................8 
1 Sensors, connectors, and adaptors.........................................................................................8 
2 Grounding ...............................................................................................................................8 
3 Software..................................................................................................................................9 
Analog in and out............................................................................................................................9 
Digital in and out.........................................................................................................................9 
Auxiliary equipment..................................................................................................................10 
Temperature compensation .....................................................................................................10 
1 Electrochemical sensors........................................................................................................10 
2 Oxygen optodes ....................................................................................................................11 
Troubleshooting........................................................................................................................11 
1 Problems logging over long periods of time.........................................................................11 
1.1 Windows Update ..........................................................................................................11 
1.2 Loss of connection to the UniAmp because of USB power saving ...............................12 
1.3 Disable power saving on the PC....................................................................................12 
2 Electrical noise ......................................................................................................................12 
 
 

1Scope of the manual

This manual covers the multichannel versions of the UniAmp: fx-6 UniAmp, x-5 UniAmp, fx-3

UniAmp, and the customized multichannel versions.

2Warranty and liability

The UniAmp meters are covered by a one-year warranty.

The warranty does not include repair or replacement necessitated by accident, neglect, misuse,

unauthorized repair, or modification of the product.

In no event will Unisense be liable for any direct, indirect, consequential or incidental damages,

including lost profits, or for any claim by any third party, arising out of the use, the results of use, or

the inability to use this product.

2.1 Repair or adjustment

Equipment that is not covered by the warranty will, if possible, be repaired by Unisense with

appropriate charges paid by the customer. In case of return of equipment please contact us for

return authorization.

For further information please see the document General terms of sale and delivery of Unisense A/S

as well as the manuals for the respective products.

3Support, ordering, and contact information

If you wish to order additional products or if you encounter any problems and need scientific or

technical assistance, please do not hesitate to contact our sales and support team. We will respond

to your inquiry within one working day.

E-mail: [email protected]om

Unisense A/S

Tueager 1

DK-8200 Aarhus N, Denmark

Tel: +45 8944 9500

Fax: +45 8944 9549

Further documentation and support may be found at www.unisense.com

4Overview

The multichannel UniAmp meters are compact and economical meters for the Unisense

electrochemical microsensors, including the STOX sensors and optodes.

The meters come with different number and combination of channels. The channels are labelled:

•pA (Pico ampere) for amperometric sensors (O2, N2O, H2, H2S, NO, STOX)

•mV (millivolt) for potentiometric sensors (pH, redox)

•Op (optical) for oxygen optodes

•T(temperature) for temperature sensors

The standard multichannel UniAmp come in the following configurations:

•fx-6 UniAmp (2 x pA, 2 x mV, 1 x Op, 1 x T)

•x-5 UniAmp (2 x pA, 2 x mV, 1 x T)

•fx-3 UniAmp (1 x pA or 1 x mV, 1 x Op, 1 x T)

Figure 1: fx-6 UniAmp

All amperometric channels (pA) have support for the ultrasensitive STOX oxygen sensor with a

detection limit of <10 nM.

The fx6 and x-5 UniAmp are also available in customized versions, with the combination of channels

decided by the customer.

The meters offer temperature compensation for all amperometric channels with a range of ± 3°C

from the calibration temperature. This will work if a temperature sensor is connected.

The UniAmp meters are USB-powered and fully integrated with the Unisense SensorTrace Suite

software, allowing any combination of Unisense electrochemical sensors and optode technology.

The user interface consists of a pop-up window (a Microsoft Windows service) that is installed in the

Windows Notification Area, also called System tray, in the lower right hand area of the screen. Using

this pop-up, you can adjust channel settings such as pre-amplification, offset, sensor polarization etc.

5Operating and setup conditions

The UniAmp meters are designed for laboratory use. Care must be taken to protect the amplifiers in

humid, dusty, and corrosive environments (e.g. field conditions) since it may affect the performance,

cause damage, or shorten lifetime. If the amplifier is used outdoors, it should be protected in a

plastic bag or similar.

Temperature: 0 to +50°C (<90% rel. humidity, non-condensing)

Power: From PC, through the USB cable

Grounding: Through the USB cable. Ensure that the PC is properly grounded.

6Installation and setup of UniAmp and software

The UniAmp instruments must be used with the SensorTrace Suite software. Install the latest version

of the software, which can be downloaded from https://www.unisense.com/Software_download/.

The Logger and Programming Tool parts of the software suite are freeware, whereas Profile, Rate,

and Photo require a license. The SensorTrace Suite is compatible with Windows versions 7 and 10.

6.1 Installation of the SensorTrace Suite software

Locate the SensorTrace Suite Setup file on your PC.

•Right-click on the file and select Run as administrator

•If you get the message Windows protected your PC, click More info

oClick Run anyway

•If you get the message Do you want to allow this app to make changes to your device? click

Yes

•In the SensorTrace Suite Setup window, accept license terms and conditions and click Install

•Follow the instruction on the screen to complete the setup

•If you have purchased a license, start one of the Suite applications (Logger, Profile, Rate,

Photo), click Help - Register license

6.2 Connect the UniAmp to the PC

Connect the UniAmp to the PC using a USB-A to USB-C cable. The drivers needed for connection will

automatically be installed. The Unisense UniAmp service is installed together with the SensorTrace

Suite. Click on the UniAmp service icon to open a window with a frame for each sensor connected to

the UniAmp (Figure 2).

NOTE: Only channels with a sensor connected will be shown!

The UniAmp instruments are powered through the USB cable and no external power supply is

needed.

NOTE: The USB cable must be a high quality shielded cable!

Figure 2: Unisense UniAmp service in the Windows Notification Area. Click the up-arrow to show hidden icons, then click the

UniAmp service icon to open it. Only channels with a sensor connected, will be shown. Here sensors for H2S, pH and O2are

connected and shown. For each channel, the UniAmp Channel Configuration window may be opened by clicking the three

grey lines (red circles), see Figure 3.

Click to open the

UniAmp Channel

Configuration window

7Getting started

The UniAmp instruments are powered from the PC through the USB cable and are operated through

the Unisense UniAmp service in the Notification Area (Figure 2). Just connect the UniAmp to the PC

and settings for the connected sensors will be available in the UniAmp service window.

7.1 Connecting sensors with automatic settings

Sensors are connected to the UniAmp by plugging in the 10-pin UniAmp connector. Amperometric

sensors (O2, N2O, H2, H2S, NO, STOX) must be connected to pA-channels, pH and redox sensors to

mV-channels, oxygen optodes to Op-channels and temperature sensors to T-channels. The E2PROM

in the sensors will automatically set up the UniAmp for working correctly with the connected sensor

(Figure 3) except for the N2O sensor where a manual pre-polarization must be performed (see 7.3

Manually setting the sensor polarization).

The green light on the UniAmp will turn off for 0.1 second when a sensor is connected, indicating

that the E2PROM has been read.

7.2 Manually setting the Pre-amplification

The Pre-Amp Range determines how the sensor signal in pico ampere (pA) is converted into a signal

in millivolt (mV). This is set by the E2PROM in the sensor, when the sensor is plugged in, but can be

changed manually. Simply select the Pre-Amp Range you want from the drop-down menu (Figure 3).

The default setting of 1 pA = 1 mV works in most cases. However, if you work with a custom sensor

with either a very low or high signal, it may be beneficial to change this. Also, for sensors that don’t

have the 10 pin UniAmp connector and that are connected through an adaptor, it may be necessary

to select the Pre-Amp Range manually.

Figure 3: UniAmp Channel Configuration window. Here an O2sensor is connected and the preset values loaded from the

E2PROM are shown to the left. The dropdown menu for the Pre-Amp Range setting is shown to the right. This window is

opened as described in Figure 2. The “Pre-Amp Range”and “Polarization”boxes are not available for pH and redox

microelectrodes.

7.3 Manually setting the sensor polarization

All amperometric sensors (O2, N2O, H2, H2S, NO, STOX) must be polarized and the correct polarization

depends on the sensor type. This is set by the E2PROM in the sensor, when the sensor is plugged in,

but it can also be set manually. Simply enter the value you want in the Polarization box (Figure 3).

NOTE: Wrong polarization may destroy the sensor

For most sensors, the polarization will never need to be modified. The N2O sensor requires that the

polarization is adjusted manually as this requires a period of pre-polarization at a more negative

polarization before it is set to the measuring polarization (see the Nitrous Oxide Sensor Manual. To

be downloaded at: https://www.unisense.com/manuals/).

7.4 Adjusting the offset

The Offset may be set manually. It may be used to displace the signal in a positive or negative

direction (Figure 3).

7.5 Setting STOX sensor parameters

The STOX sensor is a double O2sensor, one sensor acts as the measuring sensor and the other acts

as the front guard. The front guard will, when it is polarized, prevent O2from reaching the measuring

O2sensor. The measuring signal, with the front guard on, is thus the signal for zero oxygen. The

measuring signal, with the front guard off, is thus the signal for O2. This difference in signal with

front guard on and off is proportional to the O2concentration. Please see the STOX Sensor Manual

for details (https://www.unisense.com/manuals/).

The cyclic polarization of the front guard must be set individually for each sensor depending on the

sensor characteristics. See the STOX sensor manual for details.

When a STOX sensor is connected to a pA channel, the Enable STOX-mode checkbox will be available

(Figure 4). Check this box to display the STOX zero on-time (s) and STOX zero off-time (s) fields.

Setting the cyclic front guard polarization timing (seconds):

•The front guard on period is specified in the STOX zero on-time (s) field

•The front guard off period is specified in the STOX zero off-time (s) field

Figure 4: UniAmp Channel Configuration window with a STOX sensor connected. The Enable STOX-mode must be checked to

display the two STOX zero on/off time fields.

7.6 Polarizing amperometric sensors without a PC connected

Amperometric sensors generally perform best after being polarized for a few hours, preferably

overnight. If you don’t have a PC available for powering the UniAmp, you may connect it to a USB

charger, i.e. an iPhone charger, or a power bank designed for smartphones. Plug in the sensors you

want to be polarized and the E2PROM will ensure correct polarization.

NOTE: N2O sensors will be polarized at the measuring polarization. Before use, it is necessary to

manually do the pre-polarization. Please see 7.3 Manually setting the sensor polarization and the

Nitrous Oxide Sensor Manual. To be downloaded at: https://www.unisense.com/manuals/.

8Sensor connections and compatibility

8.1 Sensors, connectors, and adaptors

Sensors for the UniAmp meters must have the 10 pin UniAmp connectors. This connector will

identify the sensor type for the UniAmp, so that the instrument will be adjusted to the specific

sensor connected. For the amperometric sensors, the polarization will be set automatically except

for the N2O sensor (see 7.3 Manually setting the sensor polarization).

The 6 pin connector for the legacy Unisense Multimeter requires and adaptor to be used with the

UniAmp instruments. If using sensors via adaptors, the sensor polarization has to be set manually,

using the Unisense pop-up window residing in the Windows Notification Area (see 7.3 Manually

setting the sensor polarization).

8.2 Grounding

The UniAmp instruments are delivered with a grounding cable with a banana plug at one end and a

silver wire at the other. This is for use with amperometric sensors only.

Grounding may help reducing electrical noise when working in environments with high levels of such

noise.

Note: Never use the grounding cable with pH and redox sensors.

For grounding the measuring setup, the banana plug is plugged into the connector on the back of

the instrument and the silver wire is dipped into the liquid where the sensor is inserted (calibration

standard, sample, water bath etc.). This will remove any difference in electrical potential between

the liquid and the sensor.

The PC must be connected to a proper grounding through its power supply and the mains cable.

Make sure that the mains supply is properly grounded.

NOTE: Some microsensors may only be used if the grounding cable is used. These sensors are

marked Grounding cable must be used to keep warranty! In this case the grounding must be

established as described above before the sensor touches the liquid and the cable must remain in

place as long as the sensor is used in the liquid.

8.3 Software

The UniAmp instruments require the latest version of the SensorTrace Suite software. Check the

version of your software in any of the applications (Logger, Profile, Rate, Programming Tool, Photo)

by clicking Help - About, or right click the UniAmp service in the Notification Area and select About. If

you are not already running the latest version of the SensorTrace Suite, please download

(https://www.unisense.com/Software_download/) and install it (see 6.1 Installation of the

SensorTrace Suite software).

9Analog in and out

The Analog in/output is located on the back of the instrument (Figure 5). Using an adaptor, it is

possible to retrieve the analog signals from all sensors for use with external analog to digital

converters. The Analog out must be activated in the UniAmp service window (Figure 3). Contact

[email protected]m if you need the adaptor. For connection to non-Unisense equipment, contact

Unisense first, to avoid damage to the instrument.

Figure 5: Connectors for Analog and Digital in and output and for the grounding cable (right).

10 Digital in and out

For future implementation and for service purposes.

11 Auxiliary equipment

Unisense provides solutions for a range of experimental setups, including bulk measurements,

microprofiling and micro-respiration. Depending on your measuring requirements, you may need

additional equipment for positioning, calibration, sample fixation, etc.

Please visit https://www.unisense.com/ for inspiration and contact Unisense for any questions you

may have.

12 Temperature compensation

12.1 Electrochemical sensors

With the UniAmp it is possible to automatically correct the sensor signal for changes in temperature

for the amperometric sensors for up to ±3°C from the calibration temperature. The compensation

may be turned on and off in the calibration window for each sensor by clicking the Temperature

compensation checkbox. To use this option, you must specify the temperature input it to be used for

the temperature correction. This may be:

•A fixed temperature, that you enter manually

•The input from a temperature sensor. This sensor must be selected from the dropdown

menu on the calibration window for each amperometric sensor.

The temperature correction of the sensor signal is automatically performed by SensorTrace (if this

option is turned on, see above) by applying this formula to the sensor signal:

    󰇛󰇜󰇛󰇜

Where:

•SignalComp is the temperature compensated signal

•SignalMeas is the non-temperature compensated signal from the sensor

•TCal and TMeas are the temperatures at calibration and at measuring

•Anumber is the temperature compensation constant.

The unit for the two Signals is that selected in Settings the Start Experiment window (Figure 6).

The Anumber for each sensor is specified on the sensor E2PROM under factory calibration. This value

has been obtained as the average value for 8 individual sensors of the same type. It is also possible

for the user to determine this constant for a sensor and to enter it manually in the calibration

window for this sensor.

See the SensorTrace Suite User Manual for details on how to calibrate sensors.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels UNISENSE Amplificateur

UNISENSE

UNISENSE MultiChannel UniAmp Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur