Unilumin UpadIV2 Manuel utilisateur
UpadIV Product Manual
I
Revision Records
Version
Revised Content
Date
01
Initial release
2019.11.8
02
Update address
2019.12.18
03
Update specification
2019.3.11
04
Update address
2020.3.25
05
Update specification
2020.5.18
The manual may be modified without any prior notice.
II
Instructions
Thank you for choosing our product. Please read the Product Manual carefully before
using the product. The manual may contain errors despite all our efforts, and may be
subject to change without prior notice. Contact us if you have any questions or
suggestion when using the manual. We will try our best to help you resolve the
problems in time, and highly appreciate your suggestions.
`
Copyright
The manual is the property of Unilumin Group Co., Ltd. The Unilumin LED’s operating
software is developed based on the Windows operating system. No part of the manual
can be transcripted, transmitted, reproduced, translated, edited, published, stored to a
retrieval system, or used in any form by any individual or organization without a prior
written permission of Unilumin.
Trademark
is the registered trademark of Unilumin Group Co., Ltd.
UpadIV Product Manual
III
Read the following content carefully to ensure correct use of the
indoor LED display products:
WARNING!
The LED display may be damaged and become irreparable if you ignore the following
warnings.
1) Do not place the LED display upside down or throwit during transport andstorage.
2) Do not incline, scratch, or crash the LED display during installation.
3) Do not wet or submerge the LED display into water.
4) Do not direct the air outlet of an air conditioner to the LED display.
5) Do not place or use the LED display in an environment with volatile, corrosive or
flammable chemical products.
6) Do not use the LED display outdoors in rainy days or when the humidity is higher
than 80%.
7) Do not clean the LED display with water or chemical solvents.
8) Do not use any electrical accessories not approved by the equipment
manufacturer.
9) Make sure the LED display and its auxiliary devices are grounded correctly and
reliably before they are used.
10) Switch off the power immediately and contact the professional personnel when the
LED display has any abnormal conditions such as peculiar smell, smoke, electric
leakage, and abnormal temperature.
IV
CAUTION!
The optimum displaying effect may fail to be achieved if you ignore the following
cautions.
1) Wear antistatic gloves when installing or repairing the product.
2) Ensure good ventilation for the LED display when designing the heat dissipation
solution.
3) Keep the storage environment of the LED display well ventilated and dry, with a
humidity not exceeding 85%.
4) Use single-phase power supply for an LED display with the total power
consumption not exceeding 3 kW, and three-phase power supply for an LED
display with the total power consumption exceeding 3 kW.
5) Ensure that the LED display is powered on at least twice per week, and at least 2
hours each time.
6) Installing the LED display in the following places may result in an equipment failure
and reduce its lifespan: near the sea, in an area with salt and alkali or sulphurous
gases, near a kitchen exhaust position, or at a place where the difference between
indoor and outdoor temperatures is great. Consult our professional personnel at
the service center if the LED display must be installed in any of these places.
UpadIV Product Manual
V
Contents
Chapter 1 Product Introduction ........................................................................1
1.1 Features...................................................................................................1
1.2 Cabinet Appearance ................................................................................2
1.3 Specification.............................................................................................3
1.4 Scope of Application ................................................................................4
Chapter 2 Installation and Wiring.....................................................................5
2.1 Out-of-Box Inspection ..............................................................................5
2.2 General Installation..................................................................................5
2.2.1 Installation of Floor-mounted LED Display.........................................5
2.2.2 Installation of Hanged LED Display................................................. 10
2.3 Wiring for LED Display.......................................................................... 12
2.3.1 Common Cables.............................................................................. 12
2.3.2 Signal Cable Connection................................................................. 13
2.3.3 Power Cable Connection................................................................. 14
2.3.4 Distribution Box for Rental LED Display.......................................... 15
Chapter 3 LED Display Control Setting......................................................... 16
3.1 Power-on Testing .................................................................................. 16
3.2 Preparation............................................................................................ 17
3.2.1 Starting the Hardware...................................................................... 17
3.2.2 Installing the Software ..................................................................... 17
3.3 Display Configuration............................................................................ 18
3.4 Brightness Adjustment .......................................................................... 22
3.5 Correction Coefficient Management ..................................................... 24
3.5.1 Setting Coefficients for a New Receiving Card ............................... 26
3.5.2 Setting Coefficients for a New Module ............................................ 29
3.6 Pre-storing Picture ................................................................................ 32
Chapter 4 LED Display Playing Setting......................................................... 34
4.1 Selecting a Playing Solution ................................................................. 34
4.2 Playing Setting...................................................................................... 35
4.2.1 Display Window Setting................................................................... 35
VI
4.2.2 Startup Setting................................................................................. 36
4.3 Editing Professional Playing Solution ................................................... 37
4.3.1 Editing the Time Segment ............................................................... 37
4.3.2 Editing the Program Page ............................................................... 39
4.3.3 Editing the Display Window............................................................. 42
4.3.4 Editing the Media............................................................................. 45
4.3.5 Playing the Media............................................................................ 49
4.4 Saving and Opening a Playing Solution ............................................... 51
Chapter 5 Startup, Shutdown, and Maintenance.......................................... 52
5.1 Startup Sequence ................................................................................. 52
5.2 Shutdown Sequence............................................................................. 52
5.3 Maintenance Sequence ........................................................................ 52
5.4 Warm-up Operation............................................................................... 53
5.4.1 Setting the Prestored Picture........................................................... 53
5.4.2 Ageing.............................................................................................. 54
5.4.3 Display Brightness and Ageing Time table...................................... 56
Chapter 6 Troubleshooting and Component Replacement........................... 57
6.1 Common Faults and Troubleshooting Methods.................................... 57
6.1.1 Failure in Lighting up the Display .................................................... 57
6.1.2 Incomplete Picture or Incorrect Position of Picture Displayed ........ 57
6.1.3 Screen Blinking................................................................................ 58
6.1.4 Blinking of a Cabinet in the Display................................................. 58
6.1.5 Failure in Lighting up of a Cabinet in the Display............................ 58
6.1.6 Failure in Lighting up Part of the Modules in the Cabinet ............... 59
6.2 Replacement of Main Components ...................................................... 59
6.2.1 Maintenance of Main Components of Cabinets .............................. 59
Chapter 7 Packaging Transportation and Storage........................................ 64
7.1 Packaging ............................................................................................. 64
7.2 Transportation....................................................................................... 64
7.3 Storage.................................................................................................. 64
Chapter 8 After-Sales and Warranty ............................................................. 65
8.1 The Warranty Terms.............................................................................. 65
UpadIV Product Manual
VII
8.2 Warranty Period .................................................................................... 65
8.3 Warranty Service................................................................................... 65
8.3.1 Warranty service type...................................................................... 65
8.4 Disclaimer ............................................................................................. 66
8.5 Warranty service process...................................................................... 67
8.6 Other..................................................................................................... 68
8.7 Product Warranty Card ......................................................................... 69
Attachment 1 - Path of Signal Cable inside the Cabinet............................... 70
Contact Information....................................................................................... 71
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Unilumin Moniteur
