Uniden OCEANUS DSC/ATIS Instructions d'utilisation et d'installation

CONFIDENTIAL / Uniden Marine Dealers Only

TECHNICAL SERVICE INFORMATION Revised june 7 – 2005

Brand: UNIDEN Type: OCEANUS DSC/ATIS

1. MMSI

1A. After purchase the user can program, one time only, the MMSI in the radio.

This is described in the user manual.

1B. To reprogram the MMSI ID the radio needs to be serviced at a Uniden Marine

Dealer that has a RESET JIG. (also to reprogram ATIS ID)

This item can be purchased from Avera B.V. The Netherlands.

1C. Procedure to reset the radio for new MMSI ID:

1. Make sure power radio is off.

2. Connect the reset jig to the accessory cable of the radio.

(red arrows on connectors!)

3. Push and hold CH UP on the radio while turning power on.

4. If display reads: “MMSI ID CLR”

reset has been succesful and MMSI ID can be reprogrammed

5. If display reads: MMSI ID INIT

* the radio has not been initialized yet

* the reset jig is not connected properly

* the reset jig is broken

In this case: Put power off, wait some minutes and follow complete procedure

again. (See step 4)

Note: During testing the RESET JIG it happened that all MMSI numbers from the

directory were deleted!

2. ATIS ID

2A. How to program ATIS is not mentioned in the user manual !

2B.1. Situation “Out of the box”:

Put power on

Press “menu”” Display “DSC Call”

Press “CH Down” Display “SET UP”

Press “Select” Display “Directory”

Press 6x “CH Down(*1) Display “ATIS ID”

Press “Select” Display “AT “ and “ID 000000000”

The first number after “ID” is not blinking, than it is NOT possible to program an ATIS

number.

2B.2 To program ATIS:

Turn power OFF

Press simultaneously “Menu” and “HI/LO” and put power on

Press “menu”” Display “DSC Call”

Press “CH Down” Display “SET UP”

Press “Select” Display “Directory”

Press 6x “CH Down (*1) Display “ATIS ID”

Press “Select” Display “AT “ and “ID 000000000”

The first number after “ID” is now blinking, and it is POSSIBLE to program an ATIS

number!

Use the numbers on the keypad of the microphone to program the ATIS number.

An ATIS number has 10 digits, the first digit is a “9” and is pre-programmed in the

unit, so you enter only the last 9 digits.

After entering the 9 digits press “ENTER”. Display “ATIS ID”

Turn power off.

Now the ATIS code is programmed in the transceiver.

2B.3 When ATIS is programmed

When a user repeats the procedure mentioned under 1 he will find the ATIS number

in the display, but NO blinking digit, so not possible to change anymore.

2B.4 To RE-Programme ATIS

Repeat as described under 2.

2C. Procedure to reset the radio for blank (000000000) new ATIS ID:

To do this the radio needs to be serviced at a Uniden Marine Dealer that has a

RESET JIG. This item can be purchased from Avera B.V. The Netherlands.

1. Make sure power radio is off.

2. Connect the reset jig to the accessory cable of the radio.

(red arrows on connectors!)

3. Push and hold CH DOWN on the radio while turning power on.

4. If display reads: “ATIS CLR”

reset has been succesful and ATIS can be reprogrammed

5. If display reads: ATIS ID INIT

the radio has not been initialized yet

the reset jig is not connected properly

the reset jig is broken

In this case wait some minutes and follow complete procedure again.

See step 4.

2D. Procedure to edit new ATIS

Please read instructions under 2B.2

3. Seagoing Mode and Inland Waterway Mode

The radio can be switched from “Seagoing Mode” to “Inland Waterway Mode”.

3A. This is mentioned in the user manual.

Press PA/MODE to switch from mode.

3B. When “WX” blinks in the display the radio is in “Inland Waterway” Mode.

4. Enable 9 extra channels

4A. The radio comes with channels for “Seagoing Mode” and “Inland Waterway

Mode”. In some countries channels in the VHF marine band are used that are not in

the standard list of channels. If a user has a license for using these channels he

needs to visit a Uniden Marine Dealer to activate this function.

4B. There are 4 extra modes:

Mode 1 L1/L2/F1/F2/F3

Mode 2 L1/L2/L3/F1/F2/F3

Mode 3 30/31

Mode 4 M1 (display N1)

4C. Procedure to activate extra modes:

1. Make sure radio is off.

2. Press simultaneously SCAN and HI/LO while turning power on.

3. Repeat step 1 and 2 to move to next mode.

4. After mode 4 the radio starts up in original mode again.

Note: Radio always start up in the last selected mode.

5. UIC/ USA – International – Canada

5A. The radio can be switched from not only for Europe from ‘Inland Waterways’ to

‘Seagoing Mode’ but also from International to USA and Canada frequency chart.

5B. Procedure to activate UIC:

1. Make sure radio is off.

2. Press simultaneously Select and HI/LO while turning power on.

3. Repeat step 1 and 2 to move to next mode.

Note: Detailed information about the frequencies and channels for the different

modes can be found in the operation specifications

AVF129 V3 / june 7 - 2005

Table des matières

Autres manuels Uniden Radio

Uniden

Uniden CB RADIO UH012 Manuel utilisateur

Uniden

Uniden BC700A Manuel utilisateur

Uniden

Uniden UH6060 Manuel utilisateur

Uniden

Uniden PRO510AXL Manuel utilisateur

Uniden

Uniden Bearcat 980 SSB Manuel utilisateur

Uniden

Uniden PRO530XL Manuel utilisateur

Uniden

Uniden Bearcat 880FM Manuel utilisateur

Uniden

Uniden BC75XLT Manuel de service

Uniden

Uniden PRO 520XL Manuel utilisateur

Uniden

Uniden SVS8025TSE Manuel utilisateur

Uniden

Uniden BEARCAT 980 Manuel de service

Uniden

Uniden BEARCAT 880 Manuel utilisateur

Uniden

Uniden UH088SX Manuel utilisateur

Uniden

Uniden UH7700NB Manuel utilisateur

Uniden

Uniden UH7700NB Manuel utilisateur

Uniden

Uniden PRO 510XL Manuel utilisateur

Uniden

Uniden UH720SX-NB Manuel utilisateur

Uniden

Uniden BC60XLT Manuel utilisateur

Uniden

Uniden Bearcat 980 SSB Manuel utilisateur

Uniden

Uniden PC122XL Manuel utilisateur

Uniden

Uniden AX44 Manuel utilisateur

Uniden

Uniden UH076SX-NB Manuel utilisateur

Uniden

Uniden Bearcat UBC3500XLT Manuel utilisateur

Uniden

Uniden PRO 540e Manuel utilisateur

Manuels Radio populaires d'autres marques

EisSound

EisSound KBSound iSelect Manuel utilisateur

Midland

Midland 1001LWX Manuel utilisateur

Konig

Konig HAV-SR41 Manuel utilisateur

Roberts

Roberts exprssion Manuel utilisateur

VDigi

VDigi DD3.0 Manuel utilisateur

Radio Shack

Radio Shack 21-1863 Manuel utilisateur

Roberts

Roberts Stream 207 Manuel utilisateur

Sony

Sony Walkman SRF-M97 Manuel utilisateur

Stanley

Stanley FatMax FMC770 Manuel utilisateur

auna

auna DAB-Radio 10026947 Manuel utilisateur

SOUNDMASTER

SOUNDMASTER UR190 Manuel utilisateur

HYT

HYT TC-320 Manuel utilisateur

auna multimedia

auna multimedia Yellowstone 10026851 Manuel utilisateur

B-Tech

B-Tech GMRS-V2 Manuel utilisateur

Weierwei

Weierwei VEV-V8 Manuel utilisateur

SOUNDMASTER

SOUNDMASTER DAB750 Manuel utilisateur

Telefunken

Telefunken TF-1505 Manuel utilisateur

Makita

Makita LXRM03 Manuel utilisateur