Uniden BT112APT Manuel utilisateur
Also included in this package:
Extra ear cushions
BT112 Bluetooth®
Headset User’s Guide
Questions? Problems? Get help on the web at www.uniden.com
or call our Customer Service line at 800-292-2294.
DC Head
USB Cable
AC Head
2
Getting to Know the Headset
CAUTION! Using the headset at high volume can cause permanent
hearing loss. To reduce the risk of hearing damage, use the
minimum volume level necessary (see Avoid Hearing Damage
section).
Volume
button
Power
port
Multifunction
button
Earhook
ring
Ear
cushion
LED
Microphone
What the buttons do
Press and release the button to activate the function. Do not press the buttons
quickly.
3
Button To do this... Do this...
Multifunction
Button (MFB)
Power on headset Press and hold for 3 seconds.
Get into pairing mode Press and hold for 5 seconds.
Power o headset Press and hold for 4 seconds
Refer to later sections in this manual for specic operational functions.
VOL
Increase volume on a call Press and release VOL side button.
Decrease volume on
a call
Press and release VOL side button until the volume
level cycles through increasing the volume and
returns to the lowest volume level.
NOTE: Only the headset can adjust the volume.
What the LED means
The BT112 has a single blue LED. It blinks or stays on according to the
current action or headset status.
If the LED... It means...
Blinks 3 times The device is powering up.
Blinks 4 times The device is powering down.
4
If the LED... It means...
Blinks twice every 5 seconds The device is in connectable mode.
Blinks once every 6 seconds The device is in connected mode.
Blinks 3 times every 5 seconds The device is in an active call.
Is on The device is in pairing mode.
The device is charging.
Is o Charging is complete.
Setting Up Your Headset
Charge the battery
Before using your headset, charge the battery for at least 2 hours.
Charging the battery completely (and keeping it charged) will help
you get the longest possible talk and standby time out of the battery.
5
Use ONLY the power adapter supplied with the headset! Using any other adapter could
damage your headset, create a re hazard, or cause a risk of electric shock.
1. Connect the adapter to the power connector on the top of the headset,
then plug it into a standard 120 volt AC (regular indoor) power outlet.
The blue LED remains on while the headset is charging.
2. Charging is complete when the blue LED turns o.
The headset beeps every 30 seconds when the battery is low. The headset
may power o if it is not charged within 30 minutes.
Pair the headset to your Bluetooth phone
Pairing is like “introducing” two Bluetooth devices and giving them
permission to connect to each other.
NOTE: The headset goes into Pairing mode automatically the rst time you use it.
1. Make sure the headset is powered o and the power adapter is not
connected (you can’t use the headset while it’s charging).
2. Press and hold MFB for 5 seconds until the blue LED is steady on, then
release it. The headset is in pairing mode and should be visible to other
Bluetooth devices.
6
3. On your phone, start a search for Bluetooth headsets or handsfree
devices. (This process may take several seconds, and it will be dierent
for each phone; see your phone’s manual for detailed instructions.)
4. Your phone should discover a device called BT112 or Headset. If your
phone asks if you want to pair with this device, answer yes.
5. When your phone prompts you for a PIN code or password to pair with
the BT112, enter 0000.
6. When the headset is paired, the LED begins ashing once in 6-second
intervals. Your phone might display a conrmation message, also.
7. Your phone might ask if you want to change the headset’s name;
generally, you should only change the name if you have more than one
BT112 headset that you use with this phone.
Connecting to your phone
Most phones connect to the headset as soon as you pair it; if yours won’t,
then turn the headset o and back on. If the headset still won’t connect,
check your phone’s owner’s manual for additional Bluetooth information.
Once the headset is paired:
7
• Whenever you turn the headset on, it will automatically try to connect
to whatever device it was connected to last.
• If the headset loses the connection (e.g., if your phone is out of range), it
reconnects automatically if the phone is back in range within 1 minute.
After 1 minute, you must press MFB to manually reconnect to the phone.
• If the headset loses connection to the phone during a call, the call is
automatically forwarded to the phone. However, the phone setting
determines if the phone will keep the forwarded call or drop it.
Using Your Headset
Put your headset on
Insert the ear cushion, then wrap the
earhook behind your ear.
Everyone’s ear has a sweet spot, a
particular angle of the speaker where
the audio comes in loud and clear.
Take a few minutes to move the headset around until you nd the best
angle for the ear cushion.
8
If you can’t nd your sweet spot or if the cushion doesn’t t comfortably
in your ear, change it to one of the other sizes that came with the headset.
Pull the cushion o gently and snap a new one on.
Wearing the headset on your left ear
If you want to wear the headset on your left ear, slide
the earhook o and turn it over.
Flip the hook over so it faces
the other direction.
Slide it back on headset and back into place.
Available Features
After the headset is connected, you can:
9
To do this... Do this...
Make a call
Make a call from your mobile phone as usual; your phone
should automatically send the call to the headset. If it
doesn’t, press and hold MFB for 2 seconds to manually send
the call to the headset.
Answer a call While the call is ringing, press MFB.
Hang up Press and release MFB.
Transfer call from
headset to phone/
from phone to
headset
During a call, press and hold MFB for 2 seconds. The headset
sends the call to your phone.
Reject an incoming
call
Press and hold MFB for 2 seconds; when you hear a beep,
release the button.
Redial the last
number
With the phone in standby, press MFB; the headset
automatically dials the last number dialed from the phone.
Adjust the volume
Press the VOL button. There are 6 volume levels that cycle as
you press the VOL button. When the highest level is reached,
the volume level cycles back down to the lowest.
10
Activate voice dialing
With the phone in standby, press and hold MFB for 2 seconds then release.
When you hear a beep, start using your phone’s voice commands. (Your
phone must support voice dialing, and all commands must be pre-
programmed.)
To deactivate voice dialing, press and hold MFB for 2 seconds until you hear
a beep.
Troubleshooting and Maintenance
If you have problems with the headset, see the suggestions in the table
below. If these suggestions don’t help, contact customer support (see the
cover for contact information).
If... Try...
The headset won’t
turn on. -Charging the battery completely.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Uniden casque
Uniden
Uniden BT108 Manuel de service
Uniden
Uniden BT-109 Manuel utilisateur
Uniden
Uniden BT110 Manuel de service
Uniden
Uniden BT112 Manuel utilisateur
Uniden
Uniden BT230 Manuel utilisateur
Uniden
Uniden BT229 - Bluetooth Headset Manuel utilisateur
Uniden
Uniden BT359 Manuel utilisateur
Uniden
Uniden BT229 - Bluetooth Headset Manuel utilisateur
Uniden
Uniden BT230 Manuel de service
Uniden
Uniden DHS100 Manuel utilisateur
Uniden
Uniden EXAI 7248 SERIES Manuel utilisateur
Uniden
Uniden BT110 Manuel utilisateur
Uniden
Uniden BT-955 Manuel utilisateur
Uniden
Uniden BT-109 Manuel utilisateur
Uniden
Uniden BTHS500 Manuel utilisateur
Uniden
Uniden BTS200 Manuel utilisateur
Uniden
Uniden BTS200 Manuel utilisateur
Uniden
Uniden DECT HS950 Manuel utilisateur
Uniden
Uniden BT229 - Bluetooth Headset Manuel de service
