Uniden Ui15 Manuel utilisateur
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
2
TABLE OF CONTENTS
3
4
5
6
7
9
10
13
15
20
20
24
28
29
31
33
Safety & Warnings .........................................................................
Booster Kit Components ......................................................................
Tools Required / Optional Equipment ................................................
How It Works ..........................................................................................
Overview ................................................................................................
Siyata Connect APP ...............................................................................
Check For Signal Strength ....................................................................
LCD Features ..........................................................................................
Manual Gain Control .............................................................................
Run Coaxial Cable .................................................................................
Install the Donor (Outdoor) Antennas .................................................
Install the Server (Indoor) Antennas .....................................................
Antenna Separation ...............................................................................
Power Up Your Cellular Booster ...........................................................
Troubleshooting ....................................................................................
FAQ ........................................................................................................
NOTE: This manual contains important safety and operating
information. Please read and follow the instructions in this manual,
failure to do so could be hazardous and result in damage to your
cellular booster.
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
3
INSTALLATION INSTRUCTIONS FOR THE
FOLLOWING CELLULAR BOOSTERS:
1
SAFETY AND WARNINGS
• Turn AC power OFF at the main circuit breaker before
working on any electrical connections.
• All AC power wiring and coaxial cable wiring must conform
to local or national codes.
• The AC rated input power must be within 10% of the voltage
requirements of the device.
• When grounding the system, a solid copper conductor no
smaller than 8 AWG should be used.
• DO NOT connect a ground wire to a gas supply line.
• DO NOT open the booster. Touching internal parts could
cause injury or damage. This will void the waranty.
!
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
4
BOOSTER KIT COMPONENTS
BOOSTERS
U5D
OUTDOOR ANTENNAS (Donor)
CABLES (various lengths available)
1
YAGI
PANEL
INDOOR ANTENNAS (Server)
PANEL
DOME
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
5
OPTIONAL ACCESSORIES
(sold separately)
2 Way Expansion Kit
Lightning Surge Protector
3 Way Expansion Kit
Universal Antenna Mounting Pole
Phillips Screwdriver Drill Cellular Phone
(to check signal strength)
Drill
TOOLS REQUIRED
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
6
HOW IT WORKS
The Uniden smart cellular booster provides enhanced in building coverage by improving
cellular signal strength in homes, buildings, of ces, and other areas where coverage is
weak or unreliable.
The system ampli es the incoming signal from the nearest cellular tower
This manual provides simple installation instructions that will have your cellular booster kit
up and running in record time.
OUTDOOR ANTENNA CELLULAR BOOSTER INDOOR ANTENNA
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
7
This guide will help you properly install your cellular booster kit. It is important
to read through all of the installation steps before installing your equipment.
Thoroughly read through the instructions, visualize where all the equipment will
need to be installed and do a soft installation before mounting any equipment.
If you do not understand the instructions in full, please contact technical
support at 1-800-215-7015.
OVERVIEW
Donor Antenna (outdoor)
Surge Protector
Booster
Server Antenna (indoor)
Splitter
(if using mutliple antenna)
Server Antennas
(optional antennas for
additional coverage)
1
2
4
3
5
6 7
&
1
2
467
3 5
GETTING STARTED
Plan the layout of your system
Before you get started you will need to plan the layout of your system. This involves
checking signal strength for signals coming from the cellular tower, as well as
antenna, booster and cable placement.
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
8
BOOSTER – select location
Install the booster in an area that is protected from the
weather, properly ventilated and is away from excessive heat
and moisture.
1
DONOR ANTENNA (outdoor) - select location
Mount the donor (outdoor) antenna in an elevated outdoor
location so that it points towards the cellular tower and away
from where the inside antenna will be located.
3
OUTDOOR COAXIAL CABLE - select location
The outdoor coaxial cable is used to connect the donor
(outdoor) antenna to the booster.
4
INDOOR COAXIAL CABLE - (if used)
The indoor coaxial cable is used to connect the server (indoor)
antenna to the booster.
5
SERVER ANTENNA (indoor)
The ideal location for the server antenna will be the area of your
property where you need to improve the signal most.
NOTE: The signal strength will be strongest closest to the antenna.
6
7COMMISSIONING THE SYSTEM
REGISTER BOOSTER TO SIYATA CONNECT
Download, Open, Create Account/Log In to the Siyata Connect
App to assist with antenna installation as well as monitor and
management of your cellular booster.
2
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
9
INSTALL THE SIYATA CONNECT APP
Using the Siyata Connect App will make the installation process easier because it allows
you to monitor your booster as you install your outdoor antenna.
Checklist:
• Please have the booster, and power supply nearby.
• Make sure that the Bluetooth feature on your mobile device is enabled before you
attempt to pair or “register” your booster to the app.
Step 1: Download the Siyata Connect App
•The application is available for download through Apple’s App Store or Google Play.
• After installing the Siyata Connect app, power up the booster to pair with the app
Step 2: Create a New Account and Log-In
• Launch the app on your mobile device.
•The app will ask if you would like to receive notications.
• On the lower left-hand corner of the screen, select New Here? Sign Up!
•Complete the Create your account set up
• Activate your account by email or phone.
NOTE: Enter the code within one minute or you will need to request a new code.
Step 3: Connect the booster to the App via Bluetooth and WiFi
•Once logged into the app, on the bottom of the screen, select Tools > Register
Device > Via Bluetooth. You will be prompted with a list of detected blue tooth
devices. Please scroll through the list and nd your bluetooth device. Please nd your
device by referencing the serial number that can be found on the label of the booster
or on packaging box.
•Selecting your device from the “Device Connect” screen will take you to the
“Network Settings” screen. At the top, select Wi-Fi before selecting your network
from the list below. Enter your Wi-Fi password when prompted, then select Join.
•Selecting “Join” will take you to the “Device Settings” screen. Once you have
entered a “Device Name”, “Device Location” and “Device Region”, the Register
button at the bottom of the screen will change from gray to red.
• Select Register. When the device registration is complete the screen will display
“Register Success”.
• Selecting Done will take you to the ‘Tools” screen/ tab. You should now register, click
your device and your booster can be monitored through your Wi-Fi network.
• Additionally, if you do not have WiFi, you can directly Select Local Monitoring > Via
Bluetooth to local control. (Bluetooth capabilities will have a limitation of 30ft.)
Contact Tech Support at 1.800.215.7015 or email at support@unidencellular.com
10
IDENTIFY THE BEST LOCATION TO INSTALL THE DONOR
(OUTDOOR) ANTENNA.
Check for signal strength
Select a location on the roof of the building to install the donor antenna,
by monitoring your cellular phone’s signal strength (signal bars) to nd the
strongest signal from your carrier’s cellular tower.
Mark the area
Mark that area as the installation location for the donor (outdoor).
Find the Area of the roof with the Best Cell Signal
PUT ANTENNA HERE
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Uniden Extenseur
Uniden
Uniden U60P 4G Manuel utilisateur
Uniden
Uniden UP20 Manuel de l'opérateur
Uniden
Uniden DRX100 Manuel utilisateur
Uniden
Uniden Um50 Manuel de l'opérateur
Uniden
Uniden Hero Series Manuel utilisateur
Uniden
Uniden U2 DB-CP Manuel utilisateur
Uniden
Uniden U60 4G CELLULAR BOOSTER UNI-2005-CPAL Manuel utilisateur
Uniden
Uniden U2 DB-CP Manuel utilisateur
Uniden
Uniden UM50 4G Instructions d'utilisation
Uniden
Uniden Link 4G Manuel utilisateur
