Ultra Start G-Series Manuel utilisateur

REV.2006.04

INSTALL GUIDE

www.ultrastarters.com

Technical Support: 866-698-5872 ext 0

[email protected]

Warning

CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH!

It is the sole responsibility of the user to place the system in Service Mode

when parking in an enclosed area ex: garage, partially enclosed area

ex: carport, or when the vehicle is being serviced.

Table of Contents Page 2

Feature List Page 3

Installer Notes

Wiring Diagrams Pages 4-5

Auto/Optional Tach Learn Page 6

System Reset Page 7

Transmitter Programming

Entering Program Mode Page 8

Quick View Programming Pages 9

Program Menu 1 Pages 10-11

Program Menu 2 Pages 12-13

Program Menu 3 Page 14

Program Menu 4 Page 15

Diagnostics Page 16

Table of Contents

INSTALL GUIDE PAGE 2

Installer Notes:

PAGE 3 INSTALL GUIDE

Feature List

- Auto Tach learning.

- Run Time: 4/15/45 minutes

- Door locks: .125s/.75s/3s / Double unlock / Ignition lock/unlock

- Horn output 5ms/10ms/50ms

- Timer or Cold Start (LT series) with 4 different start intervals

- Programmable Wait to Start or (+/-) diesel Glow plug input

- Ground While Running/Anti-grind protection/Starter kill

- System Override Protection/Service Mode (Valet)

- Park light and LED diagnostics

- Panic mode - Car Finder mode

- Engine Idle mode - Turbo Timer mode

- Over load proection

INSTALL GUIDE PAGE 4

Wiring Diagram

YELLOW

WHITE/VIOLET

BLUE/WHITE

GREEN

RED/WHITE

WHITE

BLUE

RED

BROWN

GREEN/WHITE

RED

ORANGE

WHITE*

WHITE/BLUE

BLACK

BLUE

PINK

Re-arm Output (-)250ma

Ground While Running Output

Tach Detection Input (A/C)

Heater/Accessory Output (+)

Trunk Release Output (-)250ma

Park Light Output (+)10amp

Diesel Wait To Start Input (+or-)

12volt Input (+)30amp

Dis-arm Output (-)250ma

Hood Pin Switch Input (-)

Ignition Output (+)

Brake Switch Input (+)

Selectable Output (+)*

Horn Output (-)

System Ground Input (-)

12volt Input (+)30amp

Negative Park Light Output (-)250ma

Starter Output (+)

*Programmable Output (see program menu).

NOTE: 250ma outputs are low current and may require additional

parts (relays) to active optional features.

SEE OVERLOAD PROTECTION, PAGE 5

PAGE 5 INSTALL GUIDE

ACTIVE RF ANTENNA**

Status Led’s Program Button

**The antenna MUST be connected for the system to operate

*The centre pin of the keyless entry harness is ONLY available with plug-in

devices such as the VP-1, DL-3, DL-7 and Data Bus Modules.

Overloading this output will damage the remote starter.

OVERLOAD PROTECTION:

All negative outputs are overload protected.

Example: Lock, Unlock, Dis-arm, Re-arm, etc...

If an output is overloaded the system will shutdown and flash the Park

Lights 9 times slowly.

** Future use.

Wiring Diagram

GREEN

RED*

BLUE

Door Lock Output (-)250ma

12volt Output (+)250ma (see notes above)*

Door Unlock Output (-)250ma

JP1

JP2

Bypass module**

Expansion module**

INSTALL GUIDE PAGE 6

IMPORTANT! The system must be Tach Learned before remote starting.

Auto Tach Learn:

Start the vehicle with the key. To confirm that a proper tach signal is

detected the system will flash the park lights and the horn (optional)

will honk three times.

Optional Tach Learn (vehicles without 12volt start output):

Press and Hold the brake pedal. Start the vehicle with the key then

press and release the program button 2-3 times within 2 seconds.

To confirm that a proper tach signal is detected the system will flash

the park lights and the horn (optional) will honk three times.

* If tach does not learn check for proper connection on the BLUE ignition

wire at the 6-pin connector. This wire should be connected to the vehicle

main ignition wire and must not turn off during the start position. If the

ignition connection is correct, reset the system (System Reset page 7).

New - If the original Tach source is changed a system reset must be

preformed before a new tach signal can be learned to the system.

For best results connect the tach wire to a fuel injector wire.

(See page 7 for System Reset).

NOTES: 1) If the vehicle does not start when the remote starter

is activated, the park lights will flash a diagnostic

code. (See Diagnostic Chart page 16).

2) If the vehicle still does not start, check all connections

and check for a factory installed Anti-Theft system.

Auto/Optional Tach Learn

PAGE 7 INSTALL GUIDE

A system reset will clear any changes made to the Program Menu’s

as well as the Tach setting. When the system reset is complete the

system must be Auto Tach learned before the remote starter will

operate.

1) Within 3 seconds turn the ignition key from “Off” to “On” 3 times,

ON-OFF-ON-OFF-ON. (Leave the key in the ON position)

2) Press and release the Program Button located on the antenna.

The park lights will turn on and the horn (optional) will honk one time.

3) Then press and hold the Program Button until the park lights flash

and the horn (optional) will honk 3 times to confirm system reset.

NOTE: System Reset does not delete the transmitter codes from

memory and does not default MENU 2, SETTING 1.

System Reset

Remote Transmitter Learn

STEP 1 - Within 3 seconds turn the ignition key to the “ON”

position three times leaving “ON” the third time.

NOTE:

STEP 3 - While holding the Program Button, press and release the

button on each of the remote transmitters to be programmed.

If the parking lights do not turn “ON”, release the Program Button and

turn the ignition to the “OFF” position, wait 5sec and repeat steps 1 & 2.

STEP 2 - Press and hold the Program Button. The park

lights will turn “ON” and the horn (optional) will

honk once. Continue to hold the Program

Button, the park lights will turn “OFF” and the

horn (optional) will honk 5 times quickly.

IMPORTANT! All remote transmitters not programmed at this time

will be erased from memory for security.

INSTALL GUIDE PAGE 8

STEP 1: With the ignition key in the “Off” position, within three seconds, turn

the ignition key to “On” position 3 times. ON-OFF-ON-OFF-ON

NOTE: Leave the key in the “On” position.

STEP 2: Press and release the program button. The park lights will flash and

the horn (optional) will honk to confirm entering program mode.

STEP 3: Select desired Program Menu See Quick view programming page 12.

The park lights will flash and horn (optional) will honk to confirm.

STEP 4: Select Programmable Setting:

a) Press and Release the Program Button the correct number of times to

select the desired Programmable Setting.

NOTE: The LEDs will flash and the horn (optional) will honk the number of times

for the appropriate Programmable Setting that has been selected.

For example: 1 flash/honk= Program Setting 1; 2 flashes/honks= Program

Setting 2; 3 flashes/honks= Setting 3; etc…

b) Press and Hold the Program Button until the park lights flash and the

horn (optional) honks the appropriate number of times of the chosen

Option in the Programmable Setting.

For example: 1 flash/honk= Option 1; 2 flashes/honks= Option 2; 3 flashes/

honks= Setting 3; etc...

NOTE: The Program Menu may be changed at any time by repeating STEP 2.

This will allow the installer to jump from one Menu, then quickly jump to

another Menu and change another Programmable Setting without

re-entering Program Mode.

To Exit: Turning the ignition key to the “Off” position or 30 seconds of no activity.

This will be confirmed with a light flash and a long horn (optional) honk.

Press and

Release the

Program Button

For Menu 3,

press the

button

For Menu 1,

press the

button

For Menu 4,

press the

button

For Menu 2,

press the

button

Entering Program Mode

Ignition 3x

On/Off

On/Off On

PAGE 9 INSTALL GUIDE

1 Flash 2 Flashes 3 Flashes 4 Flashes

Menu 1 - Lock Button

1. Ignition Lock Disabled Enabled Lock Only

2. Door Lock/Unlock Pulses 0.750 sec. Pulse 0.125 sec. Pulse 3 sec. Pulse Double Unlock

3. Disarm Pulse 0.750 sec. Pulse 0.125 sec. Pulse

4. Re-Lock Pulse Normal Before/ After/ Shutdown Shutdown Only

5. Horn Output All Enabled Lock/ Unlock Enabled Chirp 2nd Lock press No chirps

6. Horn Timing 10 ms (regular) 5 ms (quiet) 50 ms (loud)

Menu 2 -Unlock Button

1. Selectable Output Setting 2nd Ignition 2nd Starter 2nd Accessory

2. Rearm/ Aux 1 Rearm (-) Starter Output

3. Rearm Output All Lock/ After Start After Start

4. Trunk/ Aux 2 Trunk (max 5 sec) Defrost Pulse Aux 2 (no disarm/unlock) Car Finder

5. Disarm/ Aux 3 Disarm Dome light supervision

6. Neg. Park Light / GWR Neg. Park Light GWR/ Anti-grind

7. Parking Lights Normal 30 seconds with Unlock

8. Secure Valet Mode Hold for 10 secs. Hold for 15 secs.

Menu 3 - Star Button

1. Gas/ Diesel Mode Gas/ (+) 30 sec. (-)/ 30 seconds (-)/ 15 seconds

2. Run Time 15 Minutes 4 Minutes 45 Minutes

3. Crank Time 5 Seconds 10 Seconds 3 Seconds

Menu 4 - Number Button

1. Tach Setting Tach (tach connected) Tachless (tach not connected)

2. Tach Adjustment Decrease 5% Increase 5%

3. Over Crank None 0.250 seconds 0.500 seconds

4. Tach wait None 0.500 seconds 1.500 seconds

Quick View Programming

*See the following pages for more detailed programming instructions.

INSTALL GUIDE PAGE 10

Menu 1

Press and

Release the

button for

Menu 1

Press and Release

the Program Button

# of Times for

Setting Chosen

Press and Hold

the Program Button

to Change Option

Ignition 3x

On/Off

On/Off On

Press and

Release the

Program

Button

Setting 1 Ignition Auto Lock

1) Disable 1 Flash/Honk Lock/Unlock with remote transmitter ONLY.

2) Enable 2 Flashes/Honks Doors Lock/Unlock with Ignition key.

3) Ignition Lock Only 3 Flashes/Honks Doors Lock when ignition is turned “ON” only.

Press & Release the Program Button 1 Time (Setting 1) Confirmed with 1 LED flash.

Press & Hold the Program Button until the appropriate # of park lights/horn (optional) honks, then release

Press & Release the Program Button to proceed to the next step.

Setting 2 Door Lock Options

1) .750 Sec. Pulse 1 Flash/Honk .750 Second Lock/Unlock Pulses.

2) .125 Sec. Pulse 2 Flashes/Honks .125 Second Lock/Unlock Pulses

3) 3 Sec. Pulse 3 Flashes/Honks 3 Second Lock & Unlock Pulses.

4) Double Unlock Pulse 4 Flashes/Honks 1=.250 sec. & 1=.500 sec. Unlock pulse.

Press & Release the Program Button 2 Times (Setting 2) Confirmed with 2 LED flashes.

Press & Hold the Program Button until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button to proceed to the next step.

Setting 3 Disarm Pulse Duration

1) Normal Pulses 750ms pulses on Unlock & Disarm outputs.

2) Short Pulses 125ms pulses on Unlock & Disarm outputs.

Press & Release the Program Button 4 Times (Setting 4) Confirmed with 4 LED flashes.

Press & Hold the Program Button until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button to proceed to the next step.

continue page 16...

1 Flash/Honk

2 Flashes/Honks

Press & Release the Program Button 3 Times (Setting 3) Confirmed with 3 LED flashes.

Press & Hold the Program Button until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button to proceed to the next step

Setting 4 Rearm Output (12 pin auxiliary connector pin 8)

1) Type 1 1 Flash/Honk Pulse with Lock and after shutdown.

2) Type 2 2 Flashes/Honks Unlock before start. Lock pulse after start and shutdown.

3) Type 3 3 Flashes/Honks Pulse after start only.

Autres manuels pour G-Series

Table des matières

Autres manuels Ultra Start Alarme de voiture

Ultra Start

Ultra Start 1280 series Manuel utilisateur

Ultra Start

Ultra Start 1270 series Manuel utilisateur

Ultra Start

Ultra Start 600 SERIES Manuel utilisateur

Ultra Start

Ultra Start 1350 SERIES Manuel utilisateur

Ultra Start

Ultra Start 45xx Series Manuel utilisateur

Ultra Start

Ultra Start 2000 Pro Series Manuel utilisateur

Ultra Start

Ultra Start 2500M SERIES Manuel utilisateur

Ultra Start

Ultra Start 42xx Manuel utilisateur

Ultra Start

Ultra Start 42 SERIES Manuel utilisateur

Ultra Start

Ultra Start 1172 SERIES Manuel utilisateur

Ultra Start

Ultra Start 640 Series Manuel utilisateur

Ultra Start

Ultra Start 440 Series Manuel utilisateur

Ultra Start

Ultra Start KEU-300 Series Manuel utilisateur

Ultra Start

Ultra Start 1270 series Manuel utilisateur

Ultra Start

Ultra Start 600 SERIES Manuel utilisateur

Ultra Start

Ultra Start 35 SERIES Manuel utilisateur

Ultra Start

Ultra Start 660 Series Manuel utilisateur

Ultra Start

Ultra Start 441 Series Manuel utilisateur

Ultra Start

Ultra Start 42 SERIES Manuel utilisateur

Ultra Start

Ultra Start 1180 SERIES Manuel utilisateur

Ultra Start

Ultra Start 1271M Manuel utilisateur

Ultra Start

Ultra Start MCS-100 Manuel utilisateur

Ultra Start

Ultra Start 45 SERIES Manuel utilisateur

Ultra Start

Ultra Start 600 SERIES Manuel utilisateur

Manuels Alarme de voiture populaires d'autres marques

Clifford

Clifford 3606X Manuel utilisateur

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuel utilisateur

Sparkrite

Sparkrite SRA8 Manuel utilisateur

Viper

Viper 4708V Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuel

Falcon

Falcon Predator XL3 Guide de l'utilisateur

Audiovox

Audiovox Auto Security XR91 Mode d'emploi

Clifford

Clifford Sabre II Manuel utilisateur

CrimeStopper

CrimeStopper CS-8717 Guide de démarrage rapide

Scytek electronic

Scytek electronic Vectra X3 Manuel utilisateur

Excalibur

Excalibur AL-1860-EDPB Manuel utilisateur

Clifford

Clifford CYBER 2 Manuel utilisateur

Gemini

Gemini 7057 Manuel utilisateur

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuel utilisateur

Magicar

Magicar FAI-440 Manuel utilisateur

Clifford

Clifford Nova 3 Manuel utilisateur

Viper

Viper 560XV Manuel utilisateur

SECO-LARM

SECO-LARM 300C Manuel utilisateur