UFO MetroLED Fiche technique
PRODUCT USER GUIDE
MetroLED Configurable Lighting
PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING
OR PERFORMING MAINTENANCE ON THE METROLED SYSTEM
Rev: C1
INTRODUCTION
Thank you for purchasing this UFO MetroLED configurable lighting system.
Please keep this user guide for future reference.
To ensure that the system is set up optimally and gives a long service life, please read
this user guide before installing, operating or performing any maintenance on the unit.
Please read this manual fully before installing, operating or performing maintenance on the
system.
METROLED USER GUIDE
2
Models covered by this manual:
• UFO MetroLED LG - L Shaped Gantry
• UFO MetroLED UG - U Shaped Gantry
• UFO MetroLED FS - Free Standing Gantry
• UFO MetroLED SP - Special Extrusion
INTRODUCTION
The UFO MetroLED is a fully configurable LED track lighting system which has
been especially designed for ease-of-use and many installation environments.
Available in multiple configurations and with spotlight and linear lighting
modules both available with a choice of 3000K or 4000K light outputs.
If your system requires reconfiguring with new parts, please contact your UFO sales
representative for advice.
INTRODUCTION
3
UFO LIGHTING
Select the correct plug and push it into the receptacle and press down until it clicks securely
into place as shown above. The plug can be removed by squeezing together the locking pins
and sliding the plug out as shown below.
Before assembly, unpack the shipment and check that all component parts against the
Component Parts List before commencing your build (see the Component Parts Section
in this User Guide)
PREPARE THE 12V PSU
The MetroLED flexible lighting track system is powered from EITHER a multifunction,
multi-voltage, 4 Amp desk top Power Supply Unit, OR an IEC input, multi-voltage boxed PSU.
4A DESKTOP PSU
Remove the Desk Top PSU from its box.
This PSU is a multi-plug device catering for UK, European and USA plugs.
INTRODUCTION
METROLED USER GUIDE
4
6ADESK TOP PSU
Remove the PSU from its packing. This PSU is an IEC mains lead device catering for UK, European
and USA plugs. Plug the mains lead into the IEC socket on the PSU – see below. The PSU is now
ready for power.
DO NOT CONNECT PSU TO DIMMER UNTIL METROLED TRACK SYSTEM IS FULLY ASSEMBLED AND
THE DIMMER IS CONNECTED
COMPONENT PARTS
MetroLED component parts are detailed below.
Item Descripon
1 3000K spotlight
2 3000K spotlight (note colour coded green dot on base)
3 4000K spotlight (no colour coding on base)
4 Wide angle trumpet and lens
5Narrow angle trumpet and lens
6 Metal extrusion fied with track insert
7 Plasc infill strip
8 Linear wash LED strip, 3000K or 4000K (3000K idenfied on base)
1234 5
6
7
8
INTRODUCTION
5
UFO LIGHTING
COMPONENT PARTS
MetroLED component parts are detailed below.
Item Descripon
9Extrusion end cap
10 45° end fing
11 Power in connector
12 Lehand rotang corner (stac corner also availbale)
13 Right hand rotang corner (stac corner also available)
14 Corner 30m foot, unthreaded, screw plate
15 Standard round 42mm foot with threaded lock nut
16 Standard round 30mm foot, unthreaded, screw plate
NOTE: ROTATING ELBOWS ARE DESIGNED TO ROTATE BY APPROXIMATELY 350° ONLY. A SMALL PLASTIC END STOP INSIDE
THE FITTING RESTRICTS THE TURN. HOWEVER, IT IS POSSIBLE TO FORCE THE TURN PAST THIS END STOP WHICH WILL
EVENTUALLY LEAD TO THE FLEXIBLE CONNECTOR INSIDE THE FITTING BEING DAMAGED. ROTATE
910
11
12 13
14 15 16
ACCESS PLATE REPLACEMENT PROCEDURE
ASSEMBLY
METROLED USER GUIDE
6
SLIDE-ON PARTS
ASSEMBLY
7
UFO LIGHTING
Most MetroLED systems are shipped either fully or partly assembled. All LEDs should be already
fitted to the 3 track extrusion. Assembly therefore will generally involve fitting together
extrusions. Gantry Legs will be marked “Le” and “Right” to avoid confusion. CAUTION –
fitting legs on the wrong side of a gantry can result in a rotating joint being incorrectly turned
and damaged. Assemble the MetroLED system as per instructions below.
All plastic MetroLED components fit into the matching keyed sections of the metal extrusions,
either by sliding on, or by twisting and locking see 2.6
Push the fitting carefully but firmly into the extrusion taking great care to avoid damaging
adjacent LEDs. Make sure the plastic fitting is pushed fully home.
ASSEMBLY
METROLED USER GUIDE
8
If LED slide on fittings are removed from the track for any reason, ensure they are the correct
way round when replacing. See examples below.
Correct - pins facing the right way Incorrect - pins facing the wrong way
Correct - pins facing the right way
Pushing LED fittings
on the wrong way will
irreparably damage
the spring contacts
ASSEMBLY
9
UFO LIGHTING
TWIST-LOCK PARTS
This is a 2 part assembly - see photographs below:
Assembly apart Push assembly into Base - turn the top assembly
so that it sits across the base as shown
Push the base assembly into the track
so that the connector pins line up with
the two tracks required.
Push down and twist the upper
assembly through 90 degrees until it
locks onto the track as shown below-
NOTE:
Care must be taken to push the
fitting firmly down so that it is fully
sitting in the track extrusion. If not
fully inserted when twisting to lock,
the plastic housing may become
damaged which will result in the
fitting not being locked in.
OPERATION
METROLED USER GUIDE
10
ELECTRICAL CONNECTIONS
There are 3 electrical connections required before connecting the system to the
mains – see drawing below:
1. Connect the extrusion power In connector track power cable to the MetroLED dimmer ensuring
correct wire colour codes
2. Connect the dimmer box and cable to MetroLED dimmer ensuring correct wire colour codes
3. Plug the 5V DC jack plug into the input socket on the MetroLED dimmer
Ce manuel convient aux modèles suivants
4
Table des matières
Manuels Projecteur populaires d'autres marques
VIZULO
VIZULO Micro Martin Guide de l'utilisateur
EuroLite
EuroLite LED IP FL-100 SMD Manuel utilisateur
Cooper Wheelock
Cooper Wheelock XB12 Manuel utilisateur
Allen + Roth
Allen + Roth 17624-000 Manuel utilisateur
ADJ
ADJ 4 STAGE PAK Manuel utilisateur
Cooper Lighting
Cooper Lighting EGL91SW233 Manuel utilisateur
