UbiBot LD1 Guide de configuration
Smart Leak Detector LD1
User Manuel
This user manual serves as a general guidance for all types of UBIBOT® Smart Water Leak Detector. Some features, which are
marked with asterisk, are available only for specific versions. Please refer to related instructions according to the version you
purchased.
PACKAGE LIST
INTRODUCTION
Device
1
User Manual
Adapter
3
User manual
4
External antenna
2
①
Note:① Please tighten the antenna before use.
Configuration button
Light and Siren Alarm
DC12V power port
Channel A
WiFi/GPRS antenna Function button
USB Type-C
Ethernet cable port*
Channel B
RS485 interface Relay control interface
1. Basic Features Introduction
1
2. Screen Icons Introduction
3.Device Operations
m
ft
m
ft
×
×
SIM
CH A
CH B
Error code
Ethernet cable connected*
AP Setup mode
SIM SIM card installed*
Sending data
Network connection/failure
WiFi connection/failure
Total rope length Water leakage alarm
Water leakage alarm
Mobile data strength*
Channel number
CH A
CH B
m
ft
Alarm symbol
Meter
Foot
Switch On/Off After the power is plugged in/unplugged, the device will Switch On/Off automatically.
With the device switched on, press and hold the Configuration button for about 5 seconds
until the AP icon flashes on the screen. Release at this time to enter the configuration mode.
With the device switched on, press the Function button once to trigger a manual data sync.
The icon will flash while the data is being transferred.
When the device alarm has been triggered, click the Configuration button to suspend the
alarm. The alarm function will be restored after 5 minutes by default. This timeframe can be
set on the platform.
Press any key to light the backlight of the device. Press the Configuration button and
Function button at the same time to keep the backlight bright.
Double press the Configuration button to enable or disable the voice guide.
Double click the function key to switch the unit (meter/foot).
With the device switched on，press and hold the menu button and power buttons together
for at least 8 seconds.
Setup Mode
Manual Data Synchronization
Pause Alarm
Display Backlight
Switch On/Off Voice Guide
Switch Meter/Foot
Reset to Default Settings
2
DEVICE SETUP OPTIONS
Option 1: Using Mobile App
SETUP USING THE APP FOR WiFi CONNECTION
Download the App from www.ubibot.com/setup, or search for 'Ubibot' on the AppStore or Google Play.
Download the tool from www.ubibot.com/setup.
This Tool is a desktop app for device setup. It is also helpful in checking setup failure reasons, MAC address,
and offline charts. You can also use it to export offline data stored in the device internal memory.
Launch the App and log in. On the home page, tap "+" to start adding your device. Then please follow the
in-app instructions to complete the setup. You can also view the demonstration video at www.ubibot.com/-
setup for step by step guidance.
We recommend you try to use the PC Tools in case the App setup fails, because the failure may be due to
mobile phone incompatibility. The PC Tools is much easier to operate and suitable for both Mac and Windows.
Input: DC12V/2A Output: DC12V, <100mA
3
Option 2: Using PC Tools
Via our app and web console (http://console.ubibot.com), you are able to view the readings as well as config-
ure your device, such as create alert rules, set data syncinterval, etc. You can find and watch the demonstration
videos at www.ubibot.com/setup.
SETUP USING THE APP FOR ETHERNET CABLE CONNECTION*
STEP 1. Connect the device with power supply and plug the Ethernet cable.
STEP 2. Launch the app and log in. On the home page, tap "+" to start adding your device. Then please
follow the in-app instructions to complete the setup. You can also view the demonstration video
at www.ubibot.com/setup for step by step guidance.
Micro
SIM
Micro SIM card * slot
4
SETUP USING THE APP FOR MOBILE NETWORK *
Before you set up the device on mobile data, please check the APN information of the SIM card used for the
UbiBot device.
An APN (Access Point Name) provides the details your device needs to connect to mobile data through your
network operator. APN details differ by network and you will need to get these from your network operator.
With the device off, insert the SIM card as indicated in the picture. Launch the app and log in. Tap the "+" to start
seng up the device. Please follow the in-app instructions to complete the setup process. Please note, the setup
will fail if you don't have data allowance.
RS485 COMMUNICATION
The default mode is the RS485 communication slave mode. If the external sensor collection time is set in the
platform, the master mode for data collection will be activated and the slave mode will be turned off automati-
cally. If the device has been networked, the setting parameters are set by the platform.
For more details, please contact your local distributor or online document.
SETUP USING PC TOOLS
STEP 1. Launch the App and log in. With the device switched on, use the Type-C USB cable provided to
connect your device to the computer. The PC Tools will automatically scan and recognize the
product ID and enter the device page.
STEP 2. Click "Network" on the left menu bar. There, you are able to set up the device on WiFi for all the
models. For the SIM or Ethernet cable setup, please click on the corresponding button to
continue.
5
DEVICE USE
1. Device Connection
2. Device Alarm
① Power supply: Please use the matching power adapter. The Type-C interface only supports USB communi-
cation.
② Detection rope: Please choose the combination of detection ropes according to the actual situation, the
longest can support 100 m. Before accessing, please unscrew the termination end on the lead wire of the
equipment, and screw the termination end at the end of the detection rope after accessing it to detect normal-
ly.
*Note: When deploying the detection rope, please make it as close to the ground as possible.
③ RS485 interface: Optional RS485 adapter cable can be used to connect the device with the host computer
and establish communication between the two, or to directly connect the external smoke probe or the
temperature and humidity probe. The above connections cannot work at the same time.
④ Relay control: DC3.5mm interface, output 12V (<100mA) when the device alarm is on. Can be externally
connected easily to the sound and light alarm, or output other voltage through the solid state relay. If you click
the configuration key to shut down the alarm function, the relay control output 12V will be closed at the same
time.
① Leakage alarm: After the detection rope is immersed in a non-corrosive conductive water solution, the water
immersion position will be calculated and displayed on the screen in real time, and, at the same time, the
alarm will be triggered. Single point leaks can be measured at the exact location, if multiple leaks are detected
at the same time, the display is between the maximum and minimum distance.
② Disconnection alarm: After the detection rope is disconnected, the disconnection alarm will be triggered
and displayed on the screen ---. ---.
*Note: The equipment is outfitted with the termination end at the factory; if unscrewed, it will automatically
trigger the disconnection alarm.
12V
RS485 A
GND
RS485 B
GND
RS485 B
RS485 A
12V
V R L
6
ERROR CODES
FAQ
DEVICE SPECIFICATION
1. Device network configuration failure reasons
① Please check whether the WiFi account password is correct;
② Please check whether the router is working properly and the network connection is normal;
③ Please make sure the device has entered the WiFi configuration mode;
④ Please check whether the WiFi band is 2.4GHz and the channel is between 1~13;
⑤ Please check the WiFi channel width is set to 20MHz or auto mode;
⑥ WiFi security type: LD1 supports OPEN, WEP and WPA/WPA2-personal;
⑦ Poor signal strength, please check the WiFi or cell phone data traffic signal strength.
7
WiFi 2.4GHz, channel 1-13 Flame resistant ABS + PC
115mm x 90mm x 55mm
Device working environment: -20 to 60℃, 10-90%RH
Built-in memory: 300,000 sending data
Support Ethernet RJ-45 port（10/100 Mbps）*
Type-C, DC 12V/1A power supply
SIM Supports Micro SIM card (15 x 12 x 0.8mm)*
02 WiFi Connection Failed: Please refer to the Troubleshooting section 3.
03 Failed to Connect to Server: Please refer to the Common Questions at https://www.ubibot.com/category/faqs/
04 Device Activation Failed: Please refer to the Troubleshooting section 1.
05 Data Save Failure: This can happen when the power is disrupted while data is being saved.
07 Data Sync Failed: Please refer to the Troubleshooting section 3.
08 No SIM Card Found: Please check the SIM card is correctly inserted.
09 Mobile Data Network Failure: Please check your SIM card is set up correctly and has been activated.
10 Network cable* not detected: Please check if your network cable* is plugged into the device.
11 Network cable* connection failure: Please check if your network cable* is working properly.
12 IP address conflict: Please check whether your IP address is in conflict with other devices.
Auto-sensing Half/Full Duplex Switched Port*
Non-corrosive conductive liquid
2.Ethernet network* configuration failure reasons
① Please check whether the network cable is properly connected to the equipment;
② whether the network cable is intact;
③ whether the connected network can access the Internet;
If the above points are not abnormal, and you still cannot activate the device, you need to check whether the
network environment allows DHCP (automatic IP allocation) devices to access the network; or re-scan the
device QR code, select Ethernet access (advanced mode), and follow the APP prompts to manually assign IP to
the device.
3. Reasons for failure to send device data
4. Can the device be used in a network-free environment?
① Check whether the router is working properly;
② If using the mobile data traffic provided by the SIM card* inside the device, you need to check
whether the SIM card* is activated; if the SIM card* is activated, check whether the power supply of the device
is normal; also check whether the amount of the mobile data traffic provided by the device SIM card* is
sufficient for the data transfer.
The device can still work without a network, and the data can be read in real time through the LCD screen view
or RS485 interface.
For more frequently asked questions, please visit www.ubibot.com and go to the [Community and Documen-
tation] page.
8
TECHNICAL SUPPORT
The UbiBot team is glad to hear your voice of our profucts and services.
For any questions or suggestions, please feel free to create a ticket in the UbiBot app. Our customer services
representatives respond within 24 hours and often in less than an hour. You can also contact the local distribu-
tors in your contry for localized service. Please go to our website to view their contacts.
PRODUCT MAINTENANCE INSTRUCTIONS
WARRANTY INFORMATION
2. The following cases are not covered by the warranty:
1. The warranty period for this product is one year from the date of purchase. The buyer is required to submit
a valid proof of purchase. During the warranty period, free repair will be provided for any failure caused by the
quality of the product under normal use. The mailing cost of the returned product is the responsibility of the
sender (one way).
① The product is out of warranty;
② product failure or damage caused by incorrect or improper operation not in accordance with the product
use instructions, configuration instructions, and product maintenance instructions;
③ accidental or man-made damage to the product, such as exceeding the temperature and humidity range of
the equipment, water-caused damage, including natural water, such as water vapor, etc., fall, abnormal
physical force, deformation, cable breakage, etc.;
④ damage due to natural wear and tear, consumption and aging, etc. (including shells, cables, etc.);
⑤ failure or damage caused by unauthorized dismantling of the product without permission;
⑥failure or damage caused by force majeure, such as earthquake, fire, lightning strike, tsunami, etc.;
⑦ other non-product design, technology, manufacturing, quality and other issues caused by the failure or
damage.
Please always follow the instructions contained in this manual.
Keep away from acidic, oxidising, flammable or explosive substances.
When handling the device, avoid using excessive force and never use sharp instruments to try and open it.
Always mount the device on a stable surface.
9
Table des matières
Autres manuels UbiBot Capteur de sécurité
