UAttend CB1000 Manuel utilisateur

PROFESSIONAL SERIES

PRODUCT GUIDE

2796 Loker Ave., Suite 111, Carlsbad, CA 92010

(800) 518-8925 Toll Free • (877) 730-3578 Fax • www.processingpoint.com

CB1000 • CB2000 • BN1500 • BN2500

uATTEND DEVICE LIMITED

WARRANTY

This Warranty covers all uAttend™ Devices and any Devices which may now or in the future be connected to your

uAttend Account.

A. Warranty and Warranty Periods. ProcessingPoint, Inc. (“PPoint”) warrants only to the original Purchaser that the

Device will be free from defects in material and workmanship for the time during which (i) the original Purchaser

subscribes to the uAttend System, and (ii) until such time the Device has been replaced (the “Warranty Period”).

B. PPoint’s Obligation Under Warranty. PPoint’s sole obligation under the above warranty shall be to repair or replace

Devices and parts during the Warranty Period. PPoint does not assume responsibility for delays in replacement or repair

of products or parts. PPoint may, at its sole discretion, replace Devices with refurbished Devices. This warranty gives

end users specic legal rights, and particular end users may also have other rights which may vary from jurisdiction to

jurisdiction.

C. DISCLAIMER OF ALL OTHER WARRANTIES. NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, ARE

GIVEN, AND PPOINT EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING AND WITHOUT

LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to

particular end users.

D. Limitations. No salesperson, representative, or agent of PPoint is authorized to make any guaranty, warranty,

or representation that contradicts the terms contained in this Limited Warranty. Any waiver, alteration, addition, or

modication to the warranties contained herein must be in writing and signed by authorized representatives of PPoint

to be valid, binding, and enforceable. PPoint does not assume responsibility for any specic application to which any

products or parts are applied including, but not limited to, compatibility with other equipment. All statements, technical

information, or recommendations relating to the products or parts are based upon tests believed to be reliable, but

do not constitute a guaranty or warranty. PPOINT SHALL NOT UNDER ANY CIRCUMSTANCES WHATSOEVER

BE LIABLE TO ANY PARTY FOR LOSS OF PROFITS, DIMINUTION OF GOOD WILL, OR ANY OTHER

SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES WHATSOEVER WITH RESPECT TO ANY CLAIM

IN CONNECTION WITH PPOINT PRODUCTS AND/OR PARTS. Some jurisdictions do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to particular end

users.

E. What May Void the Warranty. This Limited Warranty shall be null and void in the following circumstances:

1. Modication or repair by the end user or any non-authorized PPoint service provider; or

2. Improper use or installation, or damage by accident or neglect, by the end user or any third party, or intentional

damage by the end user or any third party; or

3. Failure of the end user or any third party to exercise caution to protect from electrostatic discharge damage and

adverse temperature, or physical abuse; or

4. Failure by the end user to follow the Return Appointment Process set forth below.

F. Return Appointment Process. As a condition precedent to the above Limited Warranty, the end user must:

1. Obtain a return material authorization (RMA) from PPoint, which will include an RMA number that must be

prominently displayed on the outside of the shipping container. Returns without an RMA number may be rejected by

PPoint and immediately returned to end user, freight collect.

2. Ship the items being returned to PPoint, freight prepaid, together with a written description of the claimed defect.

3. Pack the items being returned in the original packing carton or equivalent. Damage in transit is end user’s

responsibility and may be cause to void the warranty claim.

G. Transportation Costs. PPoint will pay surface freight to return products covered by this Limited Warranty. However,

if PPoint determines in the exercise of its reasonable but sole discretion that the product or part returned for warranty

service is not defective, or does not otherwise qualify for warranty service, the end user shall be liable for all costs of

handling and transportation.

TABLE OF CONTENTS

1.0 INTRODUCTION 2

2.0 SETTING UP YOUR uATTEND ACCOUNT 2

2.1 Creating an Account 2

2.2 Adding Departments and Employees 4

2.2.1 Adding Departments 4

2.2.2 Adding Employees 5

3.0 SETTING UP AND USING THE CB1000 6

3.1 Mounting Your CB1000 6

3.2 Linking the CB1000 to Your uAttend Account 7

3.3 Overview of the CB1000 8

3.3.1 Using the CB1000 Keypad 8

3.3.2 Using the CB1000 Menus 8

4.0 SETTING UP AND USING THE CB2000 10

4.1 Mounting Your CB2000 10

4.2 Linking the CB2000 to Your uAttend Account 11

4.2.1 Connecting via WIFI Router 12

4.2.2 Connecting via LAN Cable 13

4.3 Overview of the CB2000 13

4.3.1 Using the CB2000 Keypad 13

4.3.2 Using the CB2000 Menus 14

5.0 SETTING UP AND USING THE BN1500 15

5.1 Mounting Your BN1500 15

5.2 Linking the BN1500 to Your uAttend Account 16

5.3 Registering Fingerprint Templates 17

5.3.1 Transferring Fingerprint Templates to Other Timeclocks 19

5.4 Overview of the BN1500 19

5.4.1 Using the BN1500 Keypad 20

5.4.2 Using the BN1500 Menus 20

6.0 SETTING UP AND USING THE BN2500 22

6.1 Mounting Your BN2500 22

6.2 Linking the BN2500 to Your uAttend Account 23

6.2.1 Connecting via WIFI Router 24

6.2.2 Connecting via LAN Cable 25

6.3 Registering Fingerprint Templates 25

6.3.1 Transferring Fingerprint Templates to Other Timeclocks 27

6.4 Overview of the BN2500 27

6.4.1 Using the BN2500 Keypad 28

6.4.2 Using the BN2500 Menus 28

7.0 TROUBLESHOOTING 30

8.0 TEMPLATE ASSIGNMENT SHEET 32

8.0 TEMPLATE ASSIGNMENT

SHEET

MAKE COPIES OF THIS PAGE FOR ADDITIONAL EMPLOYEES, IF NEEDED.

EMPLOYEE

NAME

FINGERPRINT ID

1.0 INTRODUCTION

Thank you for purchasing your Professional SeriesTM uAttendTM Timeclock, part of

the uAttend Employee Management System by ProcessingPoint, Inc. This document

will guide you through the steps of setting up your uAttend account, setting up your

timeclock, and linking the timeclock to your uAttend account. It will also give an

overview of the features and functionality of the CB1000, CB2000, BN1500, and

BN2500 timeclocks.

To get started with uAttend, you will need to perform these tasks in the following order:

1. Create your uAttend account, using the steps provided in Section 2.1.

2. Add departments, using the steps provided in Section 2.2.

3. Add employees, using the steps provided in Section 2.2.

4. Set up your timeclock, using the steps provided in one of the following

sections:

For information on the CB1000, see Section 3.0 beginning on page 6.

For information on the CB2000, see Section 4.0 beginning on page 10.

For information on the BN1500, see Section 5.0 beginning on page 15.

For information on the BN2500, see Section 6.0 beginning on page 22.

2.0 SETTING UP YOUR

uATTEND ACCOUNT

This section describes the steps you will take to create a new uAttend account and

set up departments and employees. After you complete Section 2.0, you can skip to

the appropriate timeclock section.

2.1 Creating an Account

1. Open your web browser and visit: http://trackmytime.com/signup

You will be prompted to enter the Dealer ID, which can be found on a sticker on

the outside of the timeclock box and on the cover of this document. If the Dealer

ID is missing, please contact Customer Support at [email protected]

or 1-800-518-8925.

2. Enter the Dealer ID.

312

ERROR MESSAGE NOTES

SERVER CONNECTION

ERROR

THIS MESSAGE DISPLAYS IF

THE TIMECLOCK IS UNABLE TO

COMMUNICATE WITH THE SERVER DUE

TO A FIREWALL, CONTENT FILTER,

OR ANY OTHER KIND OF NETWORK

BLOCK.

DNS ERROR THIS MESSAGE DISPLAYS IF THE

TIMECLOCK DOES NOT HAVE A

VALID DNS SERVER IP ADDRESS TO

CONTACT, OR THE DNS SERVER IT

IS CONTACTING CANNOT PROPERLY

RESOLVE THE HOST NAME FOR THE

SERVER.

DHCP ERROR THIS MESSAGE DISPLAYS IF THE

TIMECLOCK DOES NOT RECEIVE

PROPER IP ADDRESS INFORMATION

PROVIDED TO IT FROM THE DHCP

SERVER.

3. Click Get Pricing.

You will be prompted to select a price plan that best suits your needs, based

on the number of employees who will use the system. The plans are delivered

via a monthly subscription. You can easily upgrade or downgrade your plan at

any time and all plans are month-to-month.

4. Click the Sign Up button for the plan that you select.

The Sign Up screen will appear, prompting you to create your login page, enter

the clock administrator, and sign up (enter billing information). See below for

more information.

Create Your Login Page—This step allows you to customize your uAttend login

page, which you and your employees will use to log in to the system. Specify an

easy URL extension (web address) for you to remember. You might wish to use a

shortened version of your company name. The URL extension cannot be longer than

20 letters or numbers and cannot contain special characters or spaces.

Enter Clock Administrator—This step allows you to enter information for the clock

administrator. This is the person who will have full access to the account and is

required to set up and manage the account. Supervisors and users will be added

later.

the billing name, billing address, and credit card information that you wish to use.

This information will be stored on our system (encrypted and secure) for recurring

monthly billing. All plans come with a 30-day money back guarantee, if you are not

satised. When you have entered all information, click Create my account.

330

7.0 TROUBLESHOOTING

See the following table for help with error messages you might encounter with the

CB1000, CB2000, BN1500, or BN2500 timeclocks.

ERROR MESSAGE NOTES

DEVICE ID ERROR THIS MESSAGE DISPLAYS WHEN THE

TIMECLOCK HAS NOT BEEN LINKED TO

A uATTEND ACCOUNT.

NET NOT FOUND THIS MESSAGE DISPLAYS IF THE

TIMECLOCK IS NOT CURRENTLY

PLUGGED INTO ANY NETWORKING

DEVICE, OR THE NETWORKING DEVICE

IT IS PLUGGED INTO IS TURNED OFF

OR IS NOT FUNCTIONING CORRECTLY.

CHECK TO MAKE SURE THAT:

• Your network allows DHCP

CONNECTIONS.

• tHe network is not beHinD

A FIREWALL THAT BLOCKS

COMMUNICATION ON PORT 80.

SORRY, DEALER ID NOT

FOUND

TRACKMYTIME.COM WILL REPORT

THIS ERROR IF THE DEALER ID

YOU ENTERED IS NOT VALID.

PLEASE CONTACT YOUR DEALER

REPRESENTATIVE FOR ASSISTANCE.

UNSUCCESSFUL LOGIN WHEN YOU ATTEMPT TO LOG IN TO

TRACKMYTIME.COM, THE LOGIN FORM

REFRESHES. THIS INDICATES THAT THE

USERNAME/PASSWORD COMBINATION

THAT YOU ENTERED WAS NOT

CORRECT.

IF YOU HAVE FORGOTTEN YOUR

USERNAME AND/OR PASSWORD, CLICK

ON THE EmAIL uSERNAmE/PASSwORd

LINK AT THE TOP OF THE PAGE.

SORRY, USER NOT FOUND THIS MESSAGE DISPLAYS IF A USER

ATTEMPTS TO PUNCH IN, BUT THEIR

FINGERPRINT ID HAS NOT BEEN

ASSIGNED TO THEIR USER PROFILE.

SORRY, USER NOT

VERIFIED

THIS MESSAGE DISPLAYS IF A USER

ATTEMPTS TO PUNCH IN, BUT THEIR

FINGERPRINT TEMPLATE HAS NOT

BEEN REGISTERED.

Once you have created your account, you will have access to the uAttend Online

Help. The link is found in the upper-right corner of the uAttend screen.

2.2 Adding Departments and Employees

After you have created your uAttend account, you will need to set up at least one

department and one employee. There is no limit to the number of departments you

can set up. However, the number of employees is limited based on the plan you

selected.

You can upgrade your plan to include more employees by clicking the Account link

in the upper-right corner of the uAttend screen.

2.2.1 Adding Departments

Follow these steps to add a department to your uAttend account:

1. Click the Departments tab on the main menu.

2. Click Add Department.

3. In the Code ﬁeld, enter a code for the department.

A code can be up to 20 characters. The code is used as a reference

to the department and will appear on timecards.

4. In the Department Name ﬁeld, enter a name for the department.

5. Click Add.

294

The Device Management menu offers the following options:

Update Time—used to synchronize a new time if time settings in the uAttend

account change.

Device ID—used to display the Device ID for the BN2500.

Upload Logo—used to import a logo from a uAttend account to display on the

BN2500.

Date Format—used to change the way that dates are displayed on the

BN2500.

Reverify Time—used to select the frequency that the BN2500 will update its

time setting.

Sounds—used to turn the BN2500 sounds on and off.

Time Format—used to change the way that time is displayed on the BN2500.

The Communications menu offers the following options:

Set IP—allows a user to set a static IP address in the BN2500. Turn off DHCP

before setting a static IP.

DHCP—used to turn DHCP on and off.

Network Settings—displays the BN2500 network settings.

Delete WIFI Settings—used to clear out the WIFI settings in the BN2500.

View WIFI Settings—displays the network to which the BN2500 is connected.

Communicating Interface—allows users to select LAN or WIFI interface.

The System Management menu offers the following options:

Reset—resets the BN2500 to the factory default settings.

Help—displays the Customer Support telephone number.

MAC Address—displays the BN2500’s MAC address.

Update Firmware—updates the rmware to the most updated version.

Firmware Version—displays the rmware version.

The department will be added to the list of departments.

6. Click the department’s name to continue adding department settings.

For help setting up departments, click the Online Help link in the

upper-right corner of the uAttend screen.

2.2.2 Adding Employees

Follow these steps to add an employee to your uAttend account:

1. Click the Users tab on the main menu.

2. Click Add User.

3. From the Role drop-down menu, select the role that you wish to

assign to the user.

Employee—users who are assigned to departments within

uAttend and will be punching in and out of the system.

Supervisor—users who are assigned departments for which they

are responsible. Supervisors may have view only or view and edit

rights.

Administrator—users who have control over the uAttend account

and are responsible for setting all preferences.

NOTE: Each uAttend account is licensed for one administrator. If you wish to add

administrators to your account, there will be an additional fee of $6.00 per month,

per administrator.

4. In the First Name ﬁeld, enter the user’s ﬁrst name.

5. In the Last Name ﬁeld, enter the user’s last name.

6. Click Add.

The new user will be added to the list of users.

7. Click the new user’s name to continue adding user settings.

NOTE: If the employee will be using a PIN to punch in, enter it in the PIN Number

eld. If they will be using an RFID Badge (CB1000 and CB2000 only), enter the

badge number that is printed on the RFID Badge in the Badge Number eld. If the

employee will be using ngerprints to punch in (BN1500 and BN2500 only), you

will register their ngerprints using the steps in Section 5.3 (BN1500) or Section

6.3 (BN2500) of this document.

Next, you can skip to the timeclock section that pertains to you.

528

6.4.1 Using the BN2500 Keypad

The following table explains the functions of each key on the BN2500 keypad.

6.4.2 Using the BN2500 Menus

There are four main menu screens on the BN2500: User Management, Device

Management, Communications, and System Management.

The User Management menu offers the following options:

Add User—used to register user templates on the BN2500.

Delete User—used to delete user templates on the BN2500.

Change Mgr Password—used to change the default manager password.

View User ID—used to identify which templates belong to a user. In this

mode, a user will press their nger on the sensor and the BN2500 will display

the Fingerprint ID.

Download Templates—used to download an existing template into a new

BN2500 timeclock.

KEY FUNCTION

1-0 FUNCTION AS THE NUMBERS THEY REPRESENT.

USE THE KEYPAD TO ENTER A PIN BY PRESSING

THE CORRECT FOUR DIGITS, THEN PRESSING OK.

ESC USED TO EXIT FROM A MENU OR CANCEL A

FUNCTION.

MENU USED TO ENTER MENU MODE. REQUIRES A

MANAGER PASSWORD. DEFAULT PASSWORD IS

53178. DEFAULT PASSWORD CAN BE CHANGED

BY A MANAGER.

UP ARROW/DEPT PRESSING THE UP ARROW/DEPT KEY

IN STANDBY MODE WILL ENABLE THE

DEPARTMENT TRANSFER FUNCTION. IN ALL

OTHER MODES, THIS KEY IS USED TO SCROLL UP.

DOWN ARROW/

PRESSING THE DOWN ARROW/ID KEY IN

STANDBY MODE WILL ALLOW A USER TO ENTER

THEIR PIN. IN ALL OTHER MODES, THIS KEY IS

USED TO SCROLL DOWN.

OK USED TO ACCEPT KEY ENTRIES.

# USED TO SWITCH BETWEEN ALPHA AND

NUMERIC DURING WIFI PASSWORD ENTRY AND

IS OTHERWISE USED AS A TOGGLE BUTTON.

3.0 SETTING UP AND USING

THE CB1000

Now that you have set up your uAttend account, you may mount your timeclock and

link it to your account.

3.1 Mounting Your CB1000

Follow these steps to mount your timeclock to a wall:

1. Find a location near a power outlet and a router, switch, or Ethernet

jack where you would like to mount the timeclock.

2. Place the metal back plate against the wall, as shown below, and

mark the four screw holes against the wall.

3. Insert the wall studs into the center of the wall marks in all four

locations.

4. Place the metal back plate against the wall, with prongs facing away

from the wall and pointing upward, and screw the back plate to the

wall in all four locations.

276

6.3.1 Transferring Fingerprint Templates to Other Timeclocks

Transferring a ngerprint template to additional timeclocks requires interaction with

both the BN2500 and your uAttend account.

Follow these steps from your uAttend account:

1. Click the Users tab on the main menu.

2. Click Manage Fingerprint Templates.

3. Check all of the ﬁngerprint templates that you wish to transfer to an

additional timeclock.

4. Use the drop-down menu to select the timeclock(s) to which you

wish to transfer the templates.

5. Click Submit.

Follow these steps on each timeclock that you selected to receive the templates:

1. Press the Menu key.

2. Enter the default password (53178) if it has not been changed, then

press OK.

The User Management icon will be selected.

3. Press OK.

4. Scroll to select Download Templates, using the down arrow key.

5. Press OK.

6. Wait for the templates to download to the timeclock.

7. At the Success screen, press OK.

6.4 Overview of the BN2500

The BN2500 timeclock is a biometric time-recording device that allows employees

to punch in or out using a ngerprint or PIN. This timeclock can store 2,000

ngerprint templates.

5. Afﬁx the timeclock to the metal back plate by lining up the four slots

in the back of the timeclock to the four metal prongs on the back plate.

Push down lightly to make sure the timeclock is securely fastened to

the back plate and wall.

6. Attach the AC120V power cord to the back of the timeclock.

3.2 Linking the CB1000 to Your uAttend Account

Follow these steps to link the CB1000 to your uAttend account:

1. Attach an Ethernet cable between the timeclock and your router,

then plug the timeclock into a power outlet.

The timeclock should be turned on, with the display illuminated.

2. Log in to your uAttend account, if you are not already logged in.

3. Click the Settings tab.

4. Click the Timeclocks link.

5. Click Add Timeclock.

6. In the Device ID ﬁeld, enter the Device ID assigned to the CB1000.

You can nd the Device ID on a sticker on the back of the timeclock. If you

cannot locate this sticker, you can also nd the Device ID in the timeclock. To do

this, press the Menu key and enter the password (default password is 53178).

Scroll to Device Management and press OK, then scroll to Device ID and press OK.

Be sure to enter the complete Device ID. An example of a Device ID is

CB1000-12345678.

726

6. The designated employee should press their ﬁnger ﬁrmly on the

sensor until you hear a beeping sound. The employee should then

remove their ﬁnger from the sensor. This process will be repeated two

more times with the same ﬁnger.

NOTE: If desired, you may repeat the ngerprint scanning process for the same

employee with a different nger, so that the employee can have a back-up template.

If you choose to scan a second ngerprint, it will also require a unique Fingerprint ID.

We recommend using the employee’s birth date in reverse order as the ID code.

7. Repeat the previous steps for each employee who will be using the

timeclock.

Follow these steps from your uAttend account:

1. Click the Settings tab on the main menu.

2. Click the Timeclocks link.

3. Click the Assign Templates link that appears next to the name of

the timeclock that you used to register the ﬁngerprint templates.

4. Assign each ﬁngerprint template to the appropriate employee,

using the Template Assignment Sheet in this guide as a reference.

The BN2500 is now ready for registered employees to punch in and out with

their ngerprints.

IMPORTANT: The BN2500 timeclock employs an advanced ngerprint sensor.

Despite the quality of the sensor, there is a segment of the population with

ngerprints that will not record. These employees can still use the timeclock to punch

in and out by using a PIN.

7. In the Name/Location ﬁeld, enter the name for the timeclock.

This eld is used to easily identify the timeclock.

8. Click Add.

9. IMPORTANT: Restart the timeclock.

The timeclock will now be linked to your uAttend account.

3.3 Overview of the CB1000

The CB1000 timeclock features an RFID reader that allows employees to punch in

or out using an RFID card or PIN.

3.3.1 Using the CB1000 Keypad

The following table explains the functions of each key on the CB1000 keypad.

3.3.2 Using the CB1000 Menus

There are three main menu screens on the CB1000: Device Management,

Communications, and System Management.

KEY FUNCTION

1-0 FUNCTION AS THE NUMBERS THEY REPRESENT.

USE THE KEYPAD TO ENTER A PIN BY PRESSING

THE CORRECT FOUR DIGITS, THEN PRESSING OK.

ESC USED TO EXIT FROM A MENU OR CANCEL A

FUNCTION.

MENU USED TO ENTER MENU MODE. REQUIRES A

MANAGER PASSWORD. DEFAULT PASSWORD IS

53178. DEFAULT PASSWORD CAN BE CHANGED

BY A MANAGER.

UP ARROW/

DEPT

PRESSING THE UP ARROW/DEPT KEY IN

STANDBY MODE WILL ENABLE THE DEPARTMENT

TRANSFER FUNCTION. IN ALL OTHER MODES,

THIS KEY IS USED TO SCROLL UP.

DOWN ARROW/

PRESSING THE DOWN ARROW/ID KEY IN

STANDBY MODE WILL ALLOW A USER TO ENTER

THEIR PIN. IN ALL OTHER MODES, THIS KEY IS

USED TO SCROLL DOWN.

OK USED TO ACCEPT KEY ENTRIES.

# USED AS A TOGGLE BUTTON.

258

5. At the Success screen, press OK.

The timeclock will now be linked to your uAttend account.

6.2.2 Connecting via LAN Cable

Follow these steps on your BN2500 to link the BN2500 to your uAttend account via

a LAN cable to a router:

The timeclock should be turned on, with the display illuminated. The timeclock will

display the prompt “Press 1 to connect to your WIFI router. Press 2 to connect via LAN.”

1. Press 2 to connect via LAN.

2. The timeclock will display the message “DHCP Conﬁguring.”

3. After successfully connecting to your network, the timeclock will

display the “System Ready” message in the upper-left corner of the

main screen.

The timeclock will now be linked to your uAttend account.

6.3 Registering Fingerprint Templates

If you are using the BN2500, you will register users’ ngerprints for punching in and

out. Registering a ngerprint template requires interaction with both the BN2500

and your uAttend account.

Follow these steps on your BN2500:

1. Press the Menu key.

2. Enter the default password (53178) if it has not been changed, then

press OK.

3. From the timeclock menu, select the ﬁrst option, User Management.

4. Select Add User.

The BN2500 will prompt you to enter a 6-digit numeric code for this template.

5. Enter an ID code for the ﬁngerprint template and press OK.

We recommend using the employee’s birth date as an ID code. For example,

a birth date of October 22, 1984 would be registered as “102284.” Each

template must be assigned a unique code. Make note of the employee’s name

and 6-digit code in the Template Assignment Sheet at the back of this guide.

You will be prompted to place a nger on the ngerprint sensor.

Autres manuels pour CB1000

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels uAttend Horloge

uAttend

uAttend CB1000 Manuel utilisateur

Manuels Horloge populaires d'autres marques

Silicon Laboratories

Silicon Laboratories SI5324 Manuel utilisateur

Heathkit

Heathkit GC-1005 Manuel utilisateur

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuel utilisateur

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuel utilisateur

ALGE-Timing

ALGE-Timing ASC3 Manuel utilisateur

Bodet

Bodet Profil 960 Manuel utilisateur

Nixie Clock

Nixie Clock Divergence Meter Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8256-AL Manuel utilisateur

Mini Gadgets

Mini Gadgets MCPro Manuel utilisateur

Casio

Casio TMR-200 Manuel utilisateur

Progetti

Progetti ILTEMPOSTRINGE Manuel

BVItech

BVItech BV-101 Manuel utilisateur

Progetti

Progetti KALIMERO Manuel

La Crosse Technology

La Crosse Technology WT-3141b Manuel

La Crosse Technology

La Crosse Technology W86531 Manuel utilisateur

Sharp

Sharp SPC900 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-50447 Manuel utilisateur

Datexx

Datexx DF0063 Manuel utilisateur