U.S. Products SOLUS-310 Mode d'emploi

105.20.2008

SOLUS-310

EXTRACTOR

120V

INFORMATION

OPERATING

INSTRUCTIONS

DO NOT OPERATE MACHINE UNTIL YOU HAVE READ

ALL SECTIONS OF THIS INSTRUCTIONS

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.

2. Keep machine from rain and snow, extremes in temperatures, and store in a

heated location. Use the machine indoors. DO NOT let the machine freeze.

3. Do not let the pump run dry.

4. Use approved chemicals only. NO SOLVENTS.

5. Wear gloves or use rags when removing quick disconnects to prevent burns.

6. Never use water above 130 ºF/54 ºC in the solution tank.

11-SOLUS310.5.20.2008

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories,

shops and offices other than normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the following:

NOTE: Read all instructions before using this machine.

WARNING!

To reduce the risk of fire, electric shock, or injury:

•Do not leave the machine unattended when it is plugged in. Unplug the unit from the outlet when

not in use and before servicing.

•To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

•Do not allow to be used as a toy. Close attention is necessary when used near children.

•Use only as described in this manual. Use only the manufacturer’s recommended attachments.

•Never add water over 130º F/54º C to the solution tank.

•Do not use with damaged cord or plug. If the machine is not working as it should, has been

dropped, damaged, left outdoors or dropped into water, return it to a service center.

•Do not pull by the cord, use the cord as a handle, close a door on the cord, or pull the cord around

sharp edges or corners. Do not run the machine over the cord. Keep the cord away from heated

surfaces. To unplug, grasp the plug, not the cord.

•Do not handle the plug, the cord or the machine with wet hands.

•Extension cords must be 12/3 and no longer than 50 feet. Replace the cord or unplug immediately

if the ground prong becomes damaged.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,

hair, and anything that may reduce air flow.

•Keep loose clothing, hair, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or

any health endangering dusts. Do not use to pick up flammable or combustible liquids such as

gasoline or use in areas where they may be present.

•Turn off all controls before unplugging.

•Use extra care when cleaning on stairs.

•Connect to a properly grounded outlet only.

•Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure,or

chemical content.

INSPECTION:

Carefully unpack and inspect your SOLUS-310R for shipping damage. Each machine is tested

and inspected before shipping. Any shipping damage incurred is the responsibility of the carrier.

You should notify the carrier immediately if you notice damage to the box or to the machine or

parts.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals, such as our Magic Fabric Cleaner. Powder chemicals

may be used, but unless mixed very thoroughly they could cause a build-up in the pump, lines,

heat exchanger and/or quick disconnects. Any problem caused by a chemical build-up is not

covered by warranty. Use a neutral cleaner with a pH between 6 and 9 to avoid premature wear

of the pump, seals, and/or other components. Damage caused by the use of strong chemicals is

not covered by the warranty.

MAINTENANCE:

For optimum performance flush the machine with clear water at the end of each working day.

Once a month, minimum, run a flushing compound through the machine to break up any mineral

or chemical build-up that may have formed. U.S. Products’ “X-1500” is recommended. The

vacuum motor, pump motor, and the pump do not require any scheduled maintenance; however,

the motors may require replacement brushes after 1000 - 1500 hours, and the pump and bypass

valve may require rebuild kits after 1000 - 1500 hours, typically (refer to machine part list for

numbers). Clean the body with an all-purpose detergent, and protect it with an automobile

interior polish. Lubricate the wheels, castors, and quick disconnects with an all purpose silicone

spray.

PARTS AND SERVICE:

Repairs, when required, should be performed by your authorized distributor who maintains an

inventory of original replacement parts and accessories. Call the distributor from whom you

purchased this machine if you need parts and service. Be sure to specify the machine model.

Have your serial number handy.

(and be sure to register your warranty: go on-line to www.usproducts.com)

Serial Number: __________________

Model: SOLUS-310

Purchase Date:_____________

Write the name and phone number of your

distributor:

_____________________________________

KNOW YOUR MACHINE

VACUUM LID -Thislidprovidesaccessintoyourrecoverytanksothatyoucancleanthetank. Thelidmust

beclosedbefore you trytoclean..

SOLUTION TANK FILL HOLE -This is where youfillthetankwith water and cleaning solution.

VACUUM HOSE BARB -Thisiswhereyou connectyourvacuumhoseto themachine.Atightconnectionis

necessaryto preventavacuum leakwhichwould reducetheamount ofsuction.

DRAIN HOSE -Thisis howyouemptythedirty waterfromyour recoverytank. Place thehoseover adrain,

andopenthecap. When cleaningout thetankattheendofajob,simplyplacethis hoseinto adrainanduse

cleanwater torinse outthedirtanddebrisfromthe tank. NOTE:be suretoclosethecaptightlybefore using

themachineagain.

HANDLES -Thehandles areusedtomove themachine. Thesehandlesallow you totiltthe machine back

ontoit’s12” wheelsforeasy maneuvering, and/orformoving on stairways.

DRAIN

HOSE

HANDLES

VACUUM

HOSE BARB

FAN

POWER CORD

RECEPTICLES

VACUUM

LID

12”

WHEELLATCH

SOLUTION HOSE

QUICK COUPLING

SWITCH

PLATE

CASTOR

SOLUTION

TANK FILL

HOLE

PSI

GAUGE

SWITCH PLATE - The switches are located on the rear of the machine, out of the way of water

FAN -Removeswarm air fromthecomponent compartment.

PSI GAUGE - indicates the pump pressure. Look at the pressure while you spray.

LATCH -Thelatch holds together thetankandthe base compartment.

SOLUTION HOSE QUICK COUPLING-Thisiswhereyouconnectthesolutionlinethatrunsfromthemachine

tothecarpet wand orhandtool.

POWER CORD RECEPTACLES - The receptacles are where the two power cords connect to the machine.

CASTOR -Swivelcastorprovideseasy maneuverability.

WHEEL-Therearwheelsare12inchesindiametertoprovidesuperioreaseoftransportationandstairclimbing.

VACUUM SWITCH (1):

This switch will illuminate when the vacuum motors are on.

The vacuum motors run off of cord #1

CIRCUIT LOCATOR (2):

When this light is on, it indicates that cord #2 (Identified by

the red “H” on the back of the extractor.) is on a separate line

from cord #1. Cord #2 supplies voltage to the heater

allowing it to heat to the temperature range indicated by the

Heat Control dial (5) on the switch plate.

BYPASS SWITCH (3):

The bypass switch will illuminate when it is activated and will

completely bypass the circuit locator system. Use the system

only when the circuit locator light will not turn on and you

know each cord is on a separate circuit.

HEAT MODE LIGHT (4):

This light will only illuminate when the heater is heating and

will turn off when it reaches operating temperature. During

normal operation, the “MODE” light will be on most of the

time.

CARPET UPHOLSTERY SWITCH (5):

This rocker switch activates a solenoid valve - when it is

turned to Upholstery - that allows most of the pump pressure

to recirculate back to the Holding tank. This allows you to

clean delicate material at low psi (about 75 psi). When the

switch is set to Carpet, the pump operates without the

solenoid and provides about 300 psi to the cleaning tool. The

pump runs off of cord #1. The pump spraying pressure will

be observable at the pressure gauge. This switch does not

light up.

PUMP ON/OFF SWITCH (6):

This switch turns the pump on and off. It will light up when it

is turned on.

CAUTION: WHEN THE BYPASS SWITCH IS ON, THE

CIRCUIT BREAKER CAN TRIP IF BOTH CORDS ARE ON THE

SAME CIRCUIT AND THE BYPASS SWITCH IS TURNED ON.

FIGURE #1

SWITCH PLATE

NEVER LET YOUR MACHINE OR YOUR WAND FREEZE

SET-UP:

1. Fill the holding tank with clear water and prespray with the detergent of your choice (we

recommend a CRI approved chemical). Mix well. Although this machine is designed to supply

instant hot water, the addition of warm water to the holding tank would increase heater

efficiency. Never use water above 130º F/54º C in the solution tank.

2. Turn off all the switches. Plug in cord #1. (This cord runs the pump and vacuum).

3. Attach the priming hose to the machine and place the open end into the tank (see Figure 2 on

previous page).

4. Turn on the pump (turn pump pressure dial all the way clockwise) and let it run until the pump

is fully primed (approximately 30 seconds to 1 minute). Once the pump is primed, turn off the

pump and disconnect the priming hose. Attach the cleaning hose and tool.

IF YOU WANT HEATED SOLUTION:

5. Plug in the the heater cord (identified by “H” on the back of the machine). NOTE: If the green

circuit indicator light does not illuminate when the heater cord is plugged in, then both cords are

on the same circuit. Try other outlets until the light comes on. See Bypass Switch section (below)

if you are unable to get a green light.

6. Turn on the pump and spray through your tool a few times to fill the lines with solution. Begin

cleaning.

7. Refill and empty the tanks as necessary.

8. When finished with the job, vacuum all unused solution into the recovery tank, and dump the tank.

Clean the tanks and filters. Clean the tool and hoses. Store the machine in a heated location.

ELECTRIC CIRCUIT LOCATOR:

This unique, patented “smart system,” operated by a solid state circuit, will inform the operator when the

two cords are plugged into separate lines by illuminating the green, indicator light. This helps prevent

tripping circuit breakers.

BYPASS SWITCH:

The bypass switch (#6) completely bypasses the circuit locator system. Use this feature when you

cannot get the green Locator light (#5) to come on and you believe that the two cords are on separate

circuits.

CAUTION: If the bypass switch is on when the two cords are plugged into the same

circuit, the breaker may trip.

AUTO VACUUM SHUTOFF:

When the recovery tank is full, the float system will shut off the vacuum motor to prevent the machine

from overflowing. The float may not work in foam. Always use a defoamer to prevent overflow. Once

the vacuum motor shuts off, the vac switch (#7) must be turned off, the recovery tank emptied, and

then the vacuum swtich turned back on (up position) to get the vacuum motor started again.

CAUTION: Always make sure the float is clean and travels freely before turning on the

machine. A float that is stuck will cause the vacuum motor to suck in water, resulting in

vac motor damage.

PUMP PRESSURE:

Make sure the cleaning tool is spraying when adjusting the pressure, otherwise the pressure reading will

be inaccurate.

SPECIFICATIONS:

Rotomolded Body:

Vacuum:

VAC Shutoff:

Pump:

Waterlift:

Heat:

Heater:

Wand:

Weight:

Dimensions:

Lifetime Warranty

Two 5.7”, 2-stage

Electronic

Positive displacement, fully adjustable 0-500 psi

86” -- 200 CFM

up to 212º F

2000 Watts

Stainless steel, double bend, twin tip

115 lbs.

24W x 28L x 41H (inches)

TROUBLE SHOOTING:

IF THIS OCCURS CHECK THIS

NO SPRAY

PUMP DOES NOT RUN

Solution tank is empty.

Clogged spray tip.

Pump not running or not primed.

Valve on wand not operating.

Check the brushes in the pump motor. Replace if necessary.

No power to pump. Test the Motor Speed Control Circuit Board and potentiometer.

Debris is plugging cleaning tool or vacuum hose.

Drain gate is not completely closed, or seals are damaged.

Vacuum dome is not seated or is damaged.

No power to motor.

Test the Electronic Float.

Test the switch.

Test the vacuum motor.

Test the Vacuum Circuit Board.

Spraying too long. Try spraying for 12-15 seconds, or about three strokes.

Heat exchanger needs to be flushed.

Wrong tool being used. Too much water passing through. Longer hose or larger

diameter hose, than standard.

Heat is not turned on. Either the green light must be on or the bypass switch must

be turned on.

No power in the wall outlet - check to see if the breaker has tripped.

No power to the bypass switch - check wiring for ‘opens.”

No power out of bypass switch, follow troubleshooting steps to isolate the problem.

Call your distributor for additional help.

LOW SUCTION

NO SUCTION

LOW HEAT

NO HEAT

SOLUS-310 EXTRACTOR

PART LIST

1 78 Light, green indicator

2 FP312 Switch, SPDT

3 FP311A Switch, SPST, with cover

4 78B Light, red, indicator

7 2093C Switch plate, Solus 310

8 4404C Mating bar

9 2105 Wheel, handle

9A 2106 Handle

10 1590 Grip, Handle

11 FP478 Float assembly, electric, water level

12 801D Hinge pin

13 FP____ Tank, Vacuum

13A FP____ Cover, vacuum motors

14 2013A Gasket, vacuum

14A 2013 Gasket, vacuum

15 408 Vacuum motor, 120V

15A 1589 Screen, 1/8 S/S mesh, vac inlet

16 2086 Lid & ring, vacuum

17 1074 Gasket, vacuum lid

18 805 Chain, 8”

19 907 Hose barb, 1-1/2”

20 1130 Strap, Velcro, 9”

21 1060C Cap, drain hose

22 156 Hose Clamp

23 1060B Hose, drain

24 FP____ Tank, Holding

25 FP545 Lid and chain, Holding Tank

26 909A Latch strike

28 1113 Hose barb, 90°, 1/2” hose

28A 1115 Hose barb, 90°, 3/8” hose

29 925 Hose, 3/8” ID X 17”, bypass hose

31 166 Hose clamp

33 946 Hose, 1/2” ID X 20”, pump inlet hose

34 207A Filter, pump inlet

36 See Miscellaneous **

37 918 Heat Sink plate

39 3000 Bracket, solenoid mounting

40 FP225 Vacuum Motor Control PCB

41 2014 Fan, 120V

42 2015 Guard, fan

43 2B1 Screw, 6-32 X 2-1/4”

44 1057B Power Cord, 12/3, 25 ft

45 1062 Receptacle, AC power in

46 1476 Strap, 17”

47 2062 Solenoid, normally closed

49 FP336 PCB mounting track, 4”

50 923B Dual Cord Sensor PCB

ITEM PARTNo DESCRIPTION ITEM PART No. DESCRIPTION

120V

MISCELLANEOUS PARTS

**FP194E Heat repair kit includes thermistor control,

thermistor probe & cutout

950CP Pump rebuild kit, valves and o-rings

250 Pump rebuild kit, piston and seals

FP____ Pump & motor, complete, with bypass

11/9/2007

51 76A Hose Clamp

52 2060 Motor, AC, for pump

53 FP____ Pump complete, no mtr

54 FP542 Hose assembly, pump to gauge

54A 210 Snubber, pulsation dampening

55 801 Hinge pin

56 27A Axle Cap

57 2092 Wheel, 12”

58 910 Axle,

60 FP____ Base

61 FP____ Castor Plate, BLack

62 905 Castor, 4”

63 951A Gauge, Pump pressure, 300 PSI

64 928 Louver, 3”, gray

65 908 Latch

66 45 Quick Disconnect, male. 1/4 p.t.

67 116 Bushing, fiber

68 115 Washer, fiber

70 168 “T” Brass

71 92A Nipple, 1/4 p.t. S/S

72 FP___ Heat Exchanger, complete

73 455 Mount bracket, heater

74 945 Valve, bypass

77 1278A Hose, heater inlet

78 313 Hose, S/S, braided, heater outlet

SOLUS-310

25 18

40 51

56 58

64 65

05.20.2008

28A

PUMP

54A

44 42 41

Pump

Inlet

Pumpto

Heater Hose

Heater to

Outlet Hose

Pump to

Gauge Hose

Bypass

Hose

13A

15A

{

14A

NOTES:

SOLUS-310

208-772-0573 •800-257-7982 •FAX: 208-772-0577

Coeur d’Alene, Idaho

VISIT US AT: http://www.usproducts.com

Table des matières

Autres manuels U.S. Products Scrubber

U.S. Products

U.S. Products Cobra-H3 Manuel utilisateur

U.S. Products

U.S. Products Solus 500R Mode d'emploi

U.S. Products

U.S. Products Solus 500 Manuel utilisateur

U.S. Products

U.S. Products Solus 310R Mode d'emploi

U.S. Products

U.S. Products MPE-400H Mode d'emploi

U.S. Products

U.S. Products HHP-150 Mode d'emploi

U.S. Products

U.S. Products PATRIOT B Mode d'emploi

U.S. Products

U.S. Products MIRAI Manuel utilisateur

U.S. Products

U.S. Products HHP-300 Mode d'emploi

U.S. Products

U.S. Products SOLUS-310-CSA Mode d'emploi

U.S. Products

U.S. Products COBRA-C2 Manuel utilisateur

U.S. Products

U.S. Products FLOODKING Mode d'emploi

U.S. Products

U.S. Products ADVANTAGE 1200 Mode d'emploi

U.S. Products

U.S. Products ADVANTAGE-100H-SC Mode d'emploi

U.S. Products

U.S. Products KC 1200-500 Mode d'emploi

U.S. Products

U.S. Products ADVANTAGE-400H-CE Mode d'emploi

U.S. Products

U.S. Products HP150-C Mode d'emploi

U.S. Products

U.S. Products PEX 500-C-TICK Mode d'emploi

U.S. Products

U.S. Products ADVANTAGE-200H Mode d'emploi

U.S. Products

U.S. Products KC-310 Mode d'emploi

U.S. Products

U.S. Products KING COBRA 500-CSA Mode d'emploi

U.S. Products

U.S. Products ADVANTAGE-200H Mode d'emploi

U.S. Products

U.S. Products COBRA-H2 Manuel utilisateur

U.S. Products

U.S. Products COBRA-H3-CE Mode d'emploi

Manuels Scrubber populaires d'autres marques

Olympus

Olympus M200H Manuel utilisateur

Clarke

Clarke BEXT 100H Manuel d'installation et d'exploitation

JOHNY VAC

JOHNY VAC JVC70BCT Manuel utilisateur

RCm

RCm Elan Series Manuel

Kärcher

Kärcher B 120 W Manuel utilisateur

Truvox

Truvox Orbis MotorScrubber 20 Manuel utilisateur

Numatic

Numatic TTB 4045/100 Manuel utilisateur

Mclennan

Mclennan C510 Manuel utilisateur

Tennant

Tennant T20 LPG Manuel utilisateur

Columbus

Columbus ARA 66 BM 100 Manuel utilisateur

Numatic

Numatic TTV 678G / 300T Manuel utilisateur

American-Lincoln

American-Lincoln 505-945 Manuel utilisateur

FIORENTINI

FIORENTINI ET 65-75 Manuel utilisateur

Floorpul

Floorpul ruby 48 blt Guide de l'utilisateur

Onyx

Onyx RX-34 Manuel utilisateur

Dustbane

Dustbane Hurricane 400 Manuel utilisateur

Sana

Sana EUJ-702 Manuel utilisateur

REMS

REMS Twist Manuel utilisateur