U-Media WUB-310A Manuel utilisateur
1
802.11b/g Wireless USB Adapter
User's Guide
Version 1.0
2
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under
47 CFR 2.1093 paragraph (d)(2).
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device was tested for typical by stander conditions that may occur during use. To comply with
FCC RF exposure requirements a minimum separation distance of 1.5cm must be maintained
between the user’s body and the device, including the antenna.
Maximum average SAR (1g) (FOR DSSS) is 0.275W/kg.
Maximum average SAR (1g) (FOR OFDM) is 0.109W/kg.
U-MEDIA declares that WUB-310A, ( FCC ID: SI5WUB310A ) is limited in CH1~CH11 for 2.4
GHz by specified firmware controlled in U.S.A.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
3
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
This transmitter must not be co-located or operation in conjunction with any other antenna or
transmitter.
4
Table of Contents
Federal Communications Commission (FCC) Interference statement 2
CEMarkWarning 3
Chapter 1 - Getting Started
1.1 About Your 802.11b/g WLAN USB Adapter 5
1.2PackageContent 5
1.3 System Requirement 5
1.4LEDDefinition 6
1.5 Adapter Hardware and Utility Installation 6
1.6 Using the Utility to Configure Your Network 14
Chapter 2 – Maintenance
2.1 The Version Screen 25
2.2 Uninstalling the Driver 25
2.3 Uninstall the Client Utility 25
2.3 Upgrading the Wireless Utility 25
5
Chapter 1 - Getting Started
This chapter introduces the Adapter and prepares you to use the Wireless Utility.
1.1 About Your 802.11b/g WLAN USB Adapter
The Adapter is an IEEE 802.11b, and 802.11g compliant wireless LAN adapter. With the Adapter,
you can enjoy wireless mobility within almost any wireless networking environment.
The following lists the main features of your Adapter.
9Your Adapter can communicate with other IEEE 802.11b/g compliant wireless devices.
9Automatic rate selection.
9Standard data transmission rates up to 54 Mbps.
9Offers 64-bit, 128-bit and 152-bit WEP (Wired Equivalent Privacy) data encryption for
network security.
9Supports IEEE802.1x and WPA (Wi-Fi Protected Access).
9Low CPU utilization allowing more computer system resources for other programs.
9A built-in antenna.
9Driver support for Windows XP/2000.
1.2 Package Content
¾802.11b/g WLAN USB Adapter
¾Installation and Manual CD
¾Quick Start Guide
¾Warranty/Registration Adapter
1.3 System Requirement
zPentium class notebook computers with at least one available USB slot
zMicrosoft Windows XP or 2K
zCD-ROM drive
6
1.4 LED Definition
The following table describes the LED on the 802.11b/g WLAN USBAdapter
LED COLOR STATUS DESCRIPTION
OFF The Adapter has no connection
Blinking Slowly The Adapter is connected
LINK Green
Blinking The Adapter is sending or receiving data
1.5 Adapter Hardware and Utility Installation
NOTE: If you have connected the USB Adapter to your computer, please
remove it first.
Follow the instructions below to install the USB Adapter and Utility.
STEP 1
Insert the Driver and Utility CD into CD drive
STEP 2
If your CD Autorun is enabled, the Main Installation Menu will show. (Otherwise open your CD
folder and double-click on the “setup.exe” file)
7
STEP 3
Click the button of INSTALL. The InstallShield wizard prepares for installation.
STEP 4
The InstallShield Wizard prompts you for confirmation. Click Next on the following menu.
8
STEP 5
Choose to install client utility and driver or install driver only.
We recommend proceeding with “Install Client Utilities and Driver”
STEP 6
A warning question will pop up, click “Yes” on it.
STEP 7
In the destination Folder screen you are asked to confirm the Destination Folder for the
application software. If you would like, you may change the destination folder to another location.
Click Next
9
STEP 8
Select a program folder and click on Next.
10
STEP 9
The installation gives you information regarding the Client Utility to be used. Click Next on it.
STEP 10
Choose the client utility. Click Next.
Table des matières
Autres manuels U-Media Adaptateur
