Tymate TM527M Instructions d'installation
Tire Pressure Monitoring System
User Instruction
Implementation Standard: GB26149-2017
1. Product Overview
1.1 Product Introduction
1.2 Safety Warnings
1.3 Installation Precautions
2. Product Features
3. Product Compositions
3.1 Monitor Buttons and LCD Image
4. Installation Guides
4.1 Monitor Installation
4.2 Sensor Installation
5. Parameter Settings
5.1 Factory Settings
5.2 Setting Order
6. Alarm Status
6.1 High Pressure Alarm
6.2 Low Pressure Alarm
6.3 High Temperature Alarm
6.4 Sudden Air Leak Alarm
6.5 Low Voltage Alarm of the Sensor Battery
7. Other Functions
8. User Code
9. Technical Parameters
10. The Disclaimer
11. Some Using Tips
12. Contact Us
01
01
01
02
02
03
03
04
04
04
07
07
07
09
09
19
10
10
11
11
11
12
12
13
14
1. Product Overview
1.1.1 Product Introduction
Thank you for choosing our tire pressure monitoring system, which is composed of
sensors and monitor.
The system is used to detect the air pressure and temperature of each tire in real time.
The collected pressure and temperature data will be sent to the monitor by means of
radio frequency. After the data is received and processed by the monitor, it will be shown
on the monitor screen to remind the user to avoid traffic accidents. The corresponding
alarms will be issued for different abnormal situations according to the standard pressure
and temperature alarm values set by the user.
The system can improve the comfort of the vehicle, reduce fuel consumption and vehicle
wear, improving dynamic performance.
Be sure to read the user instruction carefully before installation and keep the
instruction for future use. Thank you!
1.1.2 Safety Warnings
Before installing the product, please read the following precautions.
1.2.1 The monitor should be installed in a location where it will not affect the driving vision.
1.2.2 The monitor should be reinforced to avoid falling during driving.
1.2.3 While driving, if the tire temperature rises sharply, the tire pressure will also rise
accordingly. If the temperature exceeds the warning value, stop the car to let it dissipate
the heat naturally to prevent brake failure or tire burst.
1.2.4 If the pressure continues to rise or drop at an accelerated rate while driving, stop to
check for air leaks or other problems.
1.2.5 When the air pressure is too high, you should be aware of a tire blow out. When
the air pressure is too low, you should pay attention to fuel consumption and balance.
1.2.6 This product can effectively monitor the tire pressure and temperature in real time,
but cannot avoid traffic accidents or tire blowouts. Using high-quality tires is as important
as this product to ensure that the tire pressure is normal.
1.2.7 When checking the displayed pressure and temperature values, please pay
attention to driving safety.
1.2.8 This product will automatically detect the tires and sound an alarm in case of
abnormal situations, so that the driver does not need to pay frequent attention to it so as
not to be distracted while driving.
Monitor
Sensor
1.3 Installation Precautions
1.3.1 There is a wireless connection between the sensor and the monitor. The
transmission distance of them is far enough. Designed with multiple anti-interference
functions, the possibility of interference to the sensor and the monitor is extremely low.
1.3.2 During the driving process, due to the thermal expansion and contraction of the air,
the tire pressure and temperature will get higher or lower, which is normal.
1.3.3 In general, tires have normal natural air leaks. The tire pressure will decrease over
time, which is a normal phenomenon and has no direct relationship with the installation of
this product.
1.3.4 If you have any problems with installation, please contact the agent or distributor.
2. Product Features
LED Color Display
Excessive Pressure and Temperature Alarm
Visual & Audible Alarm
Multiple Pressure Unit Options (PSI, BAR)
Multiple Temperature Unit Options (˫/ ˭)
Setting Standard Alarm Values for the Tire Pressure and Temperature
Arbitrary Interchangeability of Tire Positions
Automatically Turning on the Monitor Backlight
Supporting up to Four Tires
Showing the Pressure or Temperature of Four Tires Simultaneously
Sudden Air Leak Alarm
Waterproof Design in the Monitor
An Independent ID Code for Each Sensor
Easy Installation and Stable Performance
External Valve Sensor, Easy Installation and Stable Performance
Designed with the Waterproof Function
Sudden Air Leak Detection and Alarm Function
Special Installation Fixture Needed to Install the Anti-theft Design
Replacing the Sensor Battery to Extend the Life span of the Sensor and Make it Easy to Use
Unique ID Code for Each Sensor
3. Product Composition
3.1 Monitor Buttons and LCD Image
Tires
DescriptionIcon
Low Voltage Alarm of the Sensor Battery
Monitor Battery Symbol
High Temperature Alarm
Fault Icon
High Pressure Alarm
Low Pressure Alarm
Sudden Air Leak Alarm
Car Battery Symbol
Down Key
Charge Socket
Pressure Unit Option: BAR or PSI
Temperature Unit Option: ˫or ȯ
SET Key Up Key
4.1 Monitor Installation
4.2 Sensor Installation
Install the monitor in a place where it is easy to see in the car. The user can directly paste
the monitor on the dashboard with double-sided tape or put up a suction cup in the
appropriate position of the windshield to attach it. Then connect one end of the cigarette
lighter charger to the monitor and the another end to the cigarette lighter in the car to
power it on.
1. The monitor should be installed in a position where it will not affect the driving vision.
2. The monitor should be reinforced to avoid falling during driving.
3. When checking the displayed pressure and temperature values while driving, please
pay attention to driving safety .
4. This product will automatically detect the tires and sound an alarm, so the driver does
not need to pay frequent attention to it so as not to be distracted while driving.
The sensor ID code has been paired before leaving the factory. The sensor can be
installed on the tire directly at the corresponding position when installing, and can be used
directly. The standard configuration is one monitor paired with 4 sensors，and each
sensor uses stickers (front left, rear left, front right, rear right) to indicate the
corresponding tire position. If there is a spare tire in the vehicle, a sticker (backup) is
required to indicate the position of the spare tire. When installing, please carefully read the
user instruction to paste the label stickers (as shown in Figure 2) to corresponding tires.
4. Installation Guides
Notice：
Corresponding Tire Position Diagram for Sensor Installation:
Installation Position Diagram:
Please install the monitor and sensor that have been equipped at the factory into the
vehicle. If there is an error code or the position of the sensor is forgotten during the
assembly process, you can re-code with the "inflatable code". (Refer to the user instruction
of the monitor for details on the operation of the inflatable code.)
Notice：
Notice：
Before installing the sensor, please make sure to turn on the monitor so that the data can
be sent to the monitor in time after the sensor is installed.
Notice：
1. Each sensor uses a sticker to indicate its tire position, and it must be accurately
installed on the corresponding tire.
2. When the voltage of the sensor battery is low, there will be a low voltage alarm on the
monitor.
3. After the sensor is installed, please check whether there is any air leak in the tire. If
necessary, use soapy water to wipe the tire valve to check.
1. First install the anti-theft hex nut into the thread of the car tire valve core.
2. Tighten the transmitter clockwise to the thread of the car tire valve core.
3. Use a clamp to tighten the anti-theft hex nut counterclockwise to the transmitter to
activate the anti-theft function.
The sensor installation steps are as follows.
Figure 2
Front Left Front Right
Rear Left Rear Right
Anti-theft Hex Nut
Anti-theft Hex Nut
Tire Valve Core
Transmitter
The steps for replacing the sensor battery are as follows.
1. Use power tools to fasten the upper cover of the sensor and the tire valve respectively,
and twirl the sensor housing counterclockwise.
2. Take out the battery from the battery clamp.
3. Install a new lithium battery CR1632 with the positive pole (+) facing upwards.
4. Screw on the sensor housing, and then use a power tool to tighten it clockwise.
Notice：
When installing the sensor housing, be sure to check whether the waterproof rubber ring is
in place. If it is damaged, please replace it with a new one before installing the housing.
Power Tool
The Negative Pole
Lithium Battery CR1632
The Positive Pole
Lithium Battery CR1632
Waterproof
Rubber Ring
5.1 Factory Settings
5.2 Setting Order
5.2.1 Pressure Unit setting
5.2.2 Temperature Unit Setting
In the standby mode, press and hold the "SET" key on the monitor. Release it after the
first beep sound, and the monitor will enter the first setting interface, and the correspond-
ing LCD symbol will flash. Then press the "SET" key to select the parameter item that
needs to be set, and press "-" or "+" to set specific parameter values. After the setting is
completed, press and hold the "SET" key and release it when you hear a beep sound. In
this way, you can save the parameters and exit to the normal standby state. When
entering the setting state, press "-" or "+" at the same time to exit the setting mode without
saving the setting data. If there is no operation within 1 minute in the setting state, the
system will automatically exit the setting mode and return to the normal standby state. The
setting order of parameter 1-7 is as follows.
When the "PSI" or "BAR"
icon is flashing, press the
"-" or "+" key to select the
pressure unit of "PSI" or
"BAR" as desired.
When the "˫" or "˭" icon
is flashing, press the "-" or
"+" key to select the
temperature unit of "˫" or
"˭" as desired.
5. Parameter Settings
Pressure Unit
High Pressure Alarm Value
Low Pressure Alarm Value
Temperature Unit
High Temperature Alarm Value
PSI
3.0BAR (44PSI)
2.0BAR (29PSI)
°C
70°C
5.2.3 High Pressure Alarm Value Setting of the Front Tire (UP)
5.2.4 Low Pressure Alarm Value Setting of the Front Tire (DO)
When the high pressure parameter and the front
tire icon are flashing, press the "-" or "+" key to
select the high pressure alarm value required by
the user.
When the low pressure parameter and the front
tire icon are flashing, press the "-" or "+" key to
select the low pressure alarm value required by
the user.
5.2.5 High Pressure Alarm Value Setting of the Rear Tire (UP)
When the high pressure parameter and the rear
tire icon are flashing, press the "-" or "+" key to
select the high pressure alarm value required by
the user.
5.2.6 Low Pressure Alarm Value Setting of the Rear Tire (DO)
When the low pressure parameter and the rear
tire icon are flashing, press the "-" or "+" key to
select the low pressure alarm value required by
the user.
5.2.7 High Temperature Alarm Value Setting (UP)
When the high temperature parameter is
flashing, press the "-" or "+" key to select the
high temperature alarm value required by the
user.
Table des matières
