TyloHelo PURE 2.0 Manuel utilisateur
2900 5202
PURE 2.0 (QSG)
Quick Start Guide
200521
Installation and User Guide
Read the user guide and instructions for the sauna heater. Electrical connections
should be performed by an authorised electrician. SAVE THESE INSTRUCTIONS! The
instructions should be given to the heater/sauna owner or person responsible for
servicing after installation.
2900 5202
Installation Guide
Figure 1 Figure 2
The control panel can be installed inside or outside the sauna/steam room. If
installing inside the sauna cabin, the upper edge must not be more than 36”(92
cm) above the floor, and must be at least 12”(30 cm) from the side of the heater.
The unit can be mounted on the wall using the double-sided adhesive supplied.
A 1-3/16”(30 mm) hole through the wall is required if mounting the control panel
directly on the wall.
Installation without Bracket
Figure 1 Figure 2
Installation with Bracket
2900 5202
A. Light - Switches light on/o
B. Indicators for light, door contact, delayed start and to show that the heater is
working (Note: Door Contact not required for USA or Canada).
C. Start, stop and error indication
D. Scroll 1 to 10 to enter settings for various functions.
E. Function selection for temperature, delayed start, operating time and humidity
(Note: Humidity setting only applies to Combi Sauna Heaters).
F. Function selection buttons.
G. Temperature display. Displays current temperature
Powering Up for the First Time: When the control is rst powered up, the 4 status
indicators (section B) will ash until communication has been successfully establis-
hed. This can take up to several minutes. When complete, the number 4 LED
(section D) will ash 4 times. And then the current temperature will display. The
”door open”LEDs may ash at the end of power up cycle. Please disregard. It refers
to a function only used for heaters in Europe. This sequence will happen anytime
the main power is turned on, o and on (i.e. circuit breaker or heater on/o switch).
The Default program is set to run for a maximum of 60 minutes and a maximum of
194°F (90°C).
G
A
B
C
D
E
F
The main power switch (1) is
at the bottom of Tyl
ö
heaters.
Switch it on, if it is not already
switched on - see gure above.
TURN ON THE MAIN POWER
SWITCH WHEN USING PURE 2.0
CONTROL WITH A TYLÖ HEATER
2900 5202
Starting Sauna: To start the sauna, press the power button (section C). The
power indicator will turn green. The last temperature and operating time will be
initiated. The LED under the number 1 (section D) will begin to ash and as the
temperature increases, the ashing LED will move to the corresponding number
(1-10)
Setting Delayed Start: You can set your control to start at a later time, up to 10
hours from the time you press the start button. Use the function selection buttons
(section F) to select the timer symbol. Use the -/+ buttons to select the number of
hours until the heater is to start (1-10 hours). Activate the delayed start by pressing
the Start button (section C).
The indicator symbol for delayed start will light (section B) and the time delay LED
will start to ash. The ashing indicator will count down and show the time remai-
ning until the heater starts. Once the heater starts, the panel will switch to showing
the set temperature automatically.
Setting Sauna Time: Sauna time is set when the heater is OFF. Use the function
selection buttons (section F) to select operating time setting. Use the -/+ buttons
to the select the operating time 1-10.
Version
LED indicators
1 2 3 4 5 6 7 8 9 10
1 h 6 min 12 min 18 min 24 min 30 min 36 min 42 min 48 min 54 min 1 h
Setting Temperature: Use the function selection button (section F) to select the
temperature setting. Use the -/+ buttons to then select the desired temperature
setting 1-10. The maximum temperature (10) is 194°F (90°C), when measured at the
temperature sensor.
1 2 3 4 5 6 7 8 9 10
104°F 115°F 124°F 135°F 144°F 155°F 163°F 174°F 183°F 194°F
40°C 46°C 51°C 57°C 62°C 68°C 73°C 79°C 84°C 90°C
Once the temperature has been set and the heater started, the set temperature will
be indicated continuously and actual temperature will be indicated by a ashing
indicator. When set point is reached, the ashing will stop.
Changing from Fahrenheit (°F) to Celsius (°C): When sauna is turned on, press and
hold left arrow (<) for ve seconds. The temperature icon will ash twice, and then
temperature format will change.
Using an External Switch: An external switch for starting/stopping the sauna can be
connected to the heaters main PCA board via RJ10 modular connection. Contact
TyloHelo Inc. for further information and to order the external switch.
2900 5202
Setting Humidity Level (Combi Heaters Only)
Use the function selection button (section F) to select the humidity setting. Use the
-/+ buttons to then select the desired humidity levels 0-10. Select 0 (o) by pres-
sing < when humidity is set to 1. Each step on the scale indicates the length of time
for which the element in the water tank will operate. Both humidity and temperatu-
re can be changed during operation. While the sauna is heating up, the amount of
steam produced depends on the temperature level that is set. Humidity is prioriti-
sed with temperature settings 1-5 and temperature is prioritised for settings 6-10.
When humidity is prioritised, steam is produced according to the setting; when
temperature is prioritised, humidity only runs once the set temperature is reached.
When the water reservoir is low, three beeps will sound and the water drop symbol
will ash. Top up with water until a long beep sounds.
After a sauna session ends, when the reservoir has been in use, a sauna drying pro-
cess will start. The sauna will be heated to 80°C for 20 minutes. The ON symbol will
ash to indicate that drying is in progress. To switch o the drying process, press
the power button (section C).
Set Temperature (approximate value, °F / °C)
1 2 3 4 5 6 7 8 9 10
104°F 115°F 124°F 135°F 144°F 155°F 163°F 174°F 183°F 194°F
40°C 46°C 51°C 57°C 62°C 68°C 73°C 79°C 84°C 90°C
Humidity Settings
Humidity is Prioritised Temperature is Prioritised
123456789 10
Tank on
(min:sec) 01:45 02:00 02:17 02:33 02:47 03:05 03:20 03:35 03:50 Continuous
Tank o
(min:sec) 02:23 02:08 01:51 01:35 01:21 01:03 00:48 00:33 00:18 No Break
Standard Settings
Soft Sauna: Set Temperature at 1 and Humidity at 10
Traditional Dry Sauna: Set Temperature at 10 and Humidity to minimum (below 1)
Suggested Settings
1) If you enjoy a ”hot” sauna: Set Temperature at 9 or 10 and Humidity at 10. Sauna will
heat rst to around 180°F (80°C), then steam will commence. With the addition of steam,
the sauna will ”feel”very hot.
2) Classic ”Tylarium”: Set Temperature to 5 or 6 and Humidity at 10. Sauna will heat rst
to around 140-150°F (60-65°C). Steam will be almost continous. A very comfortable and
enjoyable sauna experience without the harsh edge.
2900 5202
Error Messages: If an error should occur on the heater or other equipment (control
panel, temperature sensor etc.) the power indicator will turn red and an error mes-
sage will be shown using LED indicators (section D). The indicator LEDs will ash
whilst one LED on the 1-10 scale is continuously lit or ashes. If it lights continuous-
ly, it refers to error message 1-10 and if it ashes, it refers to error messages 11-20.
Error Messages
– indicates not relevant to this application
1. Temperature sensor not connected or faulty
2. Temperature sensor in steam tank not connected or faulty.
3. Heater circuit board overheated
4. The level electrodes in the tank are short-circuited (Combi)
5. The steam tank overfull level electrodes are not working.
6. Contact lost with the heater network control panel node.
7. Contact lost with the heater grid node temperature/humidity sensor.
8. The steam tank has overheated.
9. Real-time clock (RTC) communication error.
10. -
11. There is a fault in the emptying of water from the steam tank. Switch o the
power and perform servicing.
12. The level electrodes are not working. Mid. failure. (Combi)
13. -
14. -
15. Contact lost with th eheater network relay board node.
16. Temperature cut-out is activate, must be reset.
17. -
18. Too many slave units connected.
19. Door has been open for more than 5 minutes when the sauna is on.
20. Door has been opened. Check sauna.
For certain errors, disconnecting current to the heater for a brief period and then
reconnecting can be tried (i.e. turning circuit breaker o and on).
Note: Error #3 refers to circuit board overheating. It will automatically reset. This
should not be confused with the heater high temperature safety limit (white stem
on left side of heater junction box). If this trips, it must be manually reset once the
heater has cooled suciently. Always investigate why the heater overheated. It can
be the result of insucient room ventilation or the rocks need to be replaced or
re-stacked.
For other errors, contact your dealer or TyloHelo Inc. Technical Support at
2900 5202
Table des matières
Autres manuels TyloHelo Panneau de contrôle
