TVision SEE515B Manuel utilisateur

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

Mounting the Camera

The camera is for outdoor mounting on a wall or under a lintel.

Installing the Camera

The camera is a ball camera and therefore can be set to most angles. First remove the camera dome

cover by unscrewing the three Torx screws using the tool supplied. A cord is attached to the dome

cover to avoid dropping it. If the camera is to be installed outdoors then before screwing the

camera base to the wall, ceiling or lintel, put silicon sealant over the holes on the bottom of the base

and around the cable entry point. Then secure the base with screws. Adjust camera position and

angle. As this is a fixed lens there are no zoom and focus controls.

Powering the Camera

The SEE515 runs on a 12V DC regulated power supply. The camera is provided with a fly lead

with a mini power red 2.1mm DC socket. It is recommended to use a power supply that is rated

higher than the current consumption of the camera i.e. the current consumption is 260mA with IRs

on so add approximately 50% headroom, and use a regulated power supply rated at 500mA or

above. The camera is polarity sensitive so connections must be correctly made.

Connecting the camera to control equipment

The dome camera comes with a fly lead for power, HD-TVI video out and CVBS (analogue

output). Connect the camera to control equipment via a female BNC-BNC lead. The green BNC is

for HD-TVI and the yellow CVBS is for analogue output. When using a co-ax type cable such as

RG59 or similar, the outer braid of the co-ax provides the “0V GROUND” connection and the inner

core provides the “Video” connection.

SEE515 Internal* HD-TVI Camera

This HD-TVI camera has a 2.1 Mega

Pixel 3.6mm fixed lens, 12x IRs with

15 metre range, IP66 rating, Panasonic

CCD, Wide Dynamic Range, Digital

Zoom, OSD menu with options for

Privacy masking, Sens-Up & Motion

and a separate (analogue connection).

The SEE515B (Black) or SEE515W (White)

cameras produce exceptional quality images

using the Panasonic CCD providing HD

1080P resolution. The true day/night

mechanical filter provides excellent colour

reproduction.

The cameras have Coaxitron Control for changing the OSD menu specifications via

the DVR or remote network connection, or via the camera joystick.

* Although this camera is classified for internal use, the camera can be effectively

used outdoors providing screw holes in the base of the camera are adequately

sealed.

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

Menu Access via DVR

Access to the camera menu is via the menu buttons on the camera or via the Up the Co-ax

connection. Access by the menu buttons is described below. To use the Up the Coax connection,

this can be accessed using the PTZ menu in the MEGA TVI or MAX TVI DVRs using the

AlienTVI(Coaxitron) protocol. This protocol is generally set in the PTZ Settings menu as default

but if not, select using the following:

Enter the DVR Menu, click on Video, PTZ and select the channel number of the TVI camera

connected to the DVR. Then click on PTZ Settings and select AlienTVI(Coaxitron) and click

OK.

Now click on the PTZ button at the

bottom of the screen and a full

screen picture will be displayed with

the PTZ control menu. Click on the

IRIS+ button to display menu

Use the directional arrows to move

up and down or right to select

options.

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

OSD Menu

The SEE515 has an on screen display menu. This can be accessed using the small joystick on the

camera lead.

Alternatively use the TVI DVR PTZ menu as detailed in “Menu Access via DVR” above.

The following menu display is shown:

FOCUS ADJ OFF

Focus adjustment display (Not relevant for fixed lens)

LENS

ELC

ALC

Mode - Normal

Mode –Indoor

EXPOSURE

BRIGHTNESS

SHUTTER

SENS-UP

AGC

RETURN

1 ~ 20

Auto / Manual-

1/25,1/50,1/100,1/240,1/500,1/1000,1/2000,1/4000,

1/8000,1/16000,1/30000, 1/60000

Off /x2/x3/x4/x5/x6/x7/x8

1 ~ 20

BACKLIGHT

OFF

HLC

BLC

WDR

Level 1 ~ 20 / Mode –All Day / Night Only

H-Pos –V-Pos –H-Size –V-Size - Return

Weight –Low / Middle / High - Return

DAY&NIGHT

EXTERN / AUTO

COLOUR / B&W

Anti-Sat. 1 ~ 20

Extern S/W High / Low

AGC Threshold 1 ~ 20

AGC Margin 1 ~ 20

Delay –Low / Middle / High - Return

WHITE BALANCE

AUTO

AUTOext

PRESET (Push)

MANUAL

Kelvin –Low / Middle / High

R-Gain 1 ~ 20

B-Gain 1 ~ 20 - Return

Press the centre button straight down

(see arrow) to enter the menu and use

Left, Right, Up and Down to move

through and amend menu settings.

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

DIGITAL NOISE

REDUCTION

DNR

Off / Low / Middle / High

IMAGE

SHARPNESS

GAMMA

COLOR GAIN

MIRROR

FLIP

D-ZOOM

ACE

DEFOG

SHADING

PRIVACY

RETURN

1 ~ 10 Default 5

0.55 / 0.6 / 0.65 /0.45 / 0.5 Default 0.5

1 ~ 20 Default 12

Off / On

1.0X ~ 8.0X

Off / Low / Middle / High (Adaptive Colour &

Contrast Enhancement)

Off / On Mode –Auto / Manual

Level - Low / Middle / High

Off / On Weight –1% ~ 100% Ret Default 100%

Off / On Zone Num (0 ~ 15) / Zone Disp Off /On

H-Pos / V-Pos / H-Size / V-Size /

Y-Level (1 ~ 20) / CR Level (1 ~ 20)

CB Level (1 ~ 20) / Return

MOTION

OFF / ON

Sensitivity 0 ~ 20

Window Tone 0 ~ 6

Det H-Pos <nn>

Det V-Pos <nn>

Det H-Size <nn>

Det V-Size <nn>

Motion OSD Off / On

Alarm Off / On

Return

<nn> value = position or size

SYSTEM

COM.

IMAGE RANGE

OUTPUT MODE

MONITOR

FRAME RATE

CVBS

LANGUAGE

COLOR BAR

RESET ON(Push)

Return

Cam ID 0 ~ 255

Baud Rate 2400 / 4800 / 9600 / 57600 /115200

USER Offset 1 ~ 20 (Default = 8) / FULL / COMP

1080P(25 FPS) / 720P(25FPS) / 720P CROP (50FPS)

0 ~ 3

25 FPS / 30 FPS

PAL / NTSC

ENG / CHN / CHN(S) / KOR / JPN / DEU / FRA /NLD

ESP / ITA

Off / On

Return

EXIT

Press IRIS + to exit

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

Menu Description

FOCUS ADJ OFF

Focus adjustment display (Not relevant for fixed lens)

LENS

ELC

ALC

Mode –Normal

Mode –Indoor

ELC Electronic Light Compensation

Electronic Light Compensation is used for cameras fitted with a board or manual Vari-Focal lens.

Press IRIS + button or joystick centre button

MODE Normal Normal lighting conditions

RETURN Return to main menu

ALC Automatic Light Compensation

Automatic Light Compensation is used for cameras fitted with an Auto DC Iris Vari-Focal lens.

Press IRIS + button or joystick centre button

MODE Indoor Normal indoor lighting conditions

RETURN Return to main menu

EXPOSURE

BRIGHTNESS

SHUTTER

SENS-UP

AGC

RETURN

1 ~ 20

Auto / Manual-

1/25,1/50,1/100,1/240,1/500,1/1000,1/2000,1/4000,

1/8000,1/16000,1/30000, 1/60000

Off /x2/x3/x4/x5/x6/x7/x8

1 ~ 20

BRIGHTNESS 1 ~ 20 (Default = 15)

Use this setting to increase brightness by opening camera iris. Useful for improving night time

viewing by using in conjunction with the Sens-Up option. However be aware to consider possible

effects when there is strong sunlight in summer that may cause the picture to white out.

SHUTTER Auto / Manual

1/25,1/50,1/100,1/240,1/500,1/1000,1/2000,1/4000,1/8000,

1/16000,1/30000, 1/60000

Shutter speed changes allow you to freeze moving objects without ghosting but reduce the amount

of available light the faster the shutter operates. At night the slower the shutter speed the more light

is available.

SENSUP Off /x2/x3/x4/x5/x6/x7/x8

The SensUp option allows the shutter speed to be reduced allowing additional light to be captured.

Increasing brightness also helps night time viewing (see BRIGHTNESS setting above).

AGC 1 ~ 20 (Default = 20)

For better performance in low light conditions the AGC (Automatic Gain Control) can be increased.

This has the effect of making the picture brighter but it may also add more noise as it amplifies all

aspects of the video signal.

RETURN

Return to main menu.

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

BACKLIGHT

OFF

HLC

BLC

WDR

Level 1 ~ 20 / Mode –All Day / Night Only

H-Pos –V-Pos –H-Size –V-Size - Return

Weight –Low / Middle / High - Return

Backlight Compensation when set, can balance light levels during day and night so that light hitting

objects viewed, is evenly spread across the picture. There are three options BLC, HLC and WDR

that can be selected.

BLC

(Backlight Compensation)

H-Pos –V-Pos –H-Size –V-Size

BLC is the standard setting for low level light differences. Select an area where BLC is required.

Using the H-Pos (Horizontal Position) and V-Pos (Vertical Position) followed by H-Size

(Horizontal Size) and V-Size (Vertical Size) create a box where light balancing is required.

HLC

(High Level Backlight Compensation)

Level 1 ~ 20 / Mode –All Day / Night Only

HLC is high level backlight compensation that will darken a bright area e.g car headlights. This can

be set for all day or night only. The lower the level the more compensation is applied. Note that

using the night option may be best as daytime pictures generally give a more even spread of light

apart from sunlight issues.

WDR

(Wide Dynamic Range)

Weight –Low / Middle / High

WDR is used for surveillance applications where there is a large difference in foreground and

background light levels. This is typical in homes and office buildings that have large areas of glass

with direct sunlight outside. Without the option switched on, views by cameras looking through

windows may not give good reproduction outside. Also where there are areas of shadow and bright

sunlight, the WDR option helps to balance light levels.

Return

Return to main menu

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

DAY&NIGHT

EXTERN / AUTO

COLOUR / B&W

Anti-Sat. 1 ~ 20

Extern S/W High / Low

AGC Threshold 1 ~ 20

AGC Margin 1 ~ 20

Delay –Low / Middle / High - Return

Day & Night menu controls light settings and predominantly provides options for using the cameras

Infra Red facilities. There are four sub-options namely External, Auto, Colour and Black & White.

EXTERNAL

This option does not use the internal CDS sensor to measure the available light. With cameras using

their own IR light source, it is often better to use the external option. Anti-Saturation helps to limit

picture saturation and External S/W (switch) can be set to High or Low limit. High switches to B/W

and Low to Colour which is opposite to the Auto, colour and B/W options. AGC threshold and

margin control video gain and Delay allows the switching from D/N or N/D to be delayed in a Low,

Middle or High time period.

AUTO

The standard Auto function uses the internal CDS to measure available light. This uses AGC

(Automatic Gain Control) and Anti Saturation to measure picture quality before switching which is

used in conjunction with a Delay time that Delay allows the switching from D/N or N/D to be

delayed in a Low, Middle or High time period.

COLOUR

This option will remain in colour mode day and night. This uses AGC (Automatic Gain Control)

and Anti Saturation.

B&W

When this option is selected the camera will remain in black and white mode, day and night. This

uses AGC (Automatic Gain Control) and Anti Saturation.

Return

Return to main menu.

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

WHITE BALANCE

AUTO

AUTOext

PRESET (Push)

MANUAL

Press IRIS+ or joystick centre button down

Kelvin –Low / Middle / High

R-Gain 1 ~ 20 (default 10)

B-Gain 1 ~ 20 (default 10)

This feature automatically adjusts the colour settings in the camera to match the type of light

available, so that white and other colours appear as natural as possible.

AUTO

This option automatically sets white balance.

AUTOext

This option is generally used to set white balance when camera is used externally.

PRESET(Push) Press IRIS+ or joystick centre button down

This option allows you to set white balance using current light levels. Settings will only change

when you press IRIS+ or joystick centre button down.

MANUAL

Use this option to manually balance light levels. Note that the manual option is used for a static

light environment and generally suitable for cameras installed indoors using constant artificial light.

Kelvin - Low / Middle / High

Sets colour temperature to low / middle / high

R-Gain 1 ~ 20

Set Red gain

B-Gain 1 ~ 20

Set Blue gain

RETURN

Return to main menu

DIGITAL NOISE

REDUCTION

DNR

Off / Low / Middle / High

DNR Off / Low / Middle / High

Digital Noise Reduction is generally applied when the Sens-Up feature is used to improve night

time views in low light conditions. Using the Sens-Up option slows the shutter speed but this

increases noise and causes grainy picture effects. DNR helps to minimise this effect. The options

low, medium and high, apply different levels of noise reduction and therefore have to be tested to

gain the best result as light levels will be different at every site and location.

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

IMAGE

SHARPNESS

GAMMA

COLOR GAIN

MIRROR

FLIP

D-ZOOM

ACE

DEFOG

SHADING

PRIVACY

RETURN

1 ~ 10 (Default 5)

0.55 / 0.6 / 0.65 /0.45 / 0.5 (Default 0.55)

1 ~ 20 (Default 12)

Off / On

1.0X ~ 8.0X (Default 1.0X)

Off / Low / Middle / High (Adaptive Colour &

Contrast Enhancement)

Off / On Mode –Auto / Manual

Level - Low / Middle / High

Off / On Weight –1% ~ 100% Default 100%

Off / On Zone Num (0 ~ 15) / Zone Disp Off /On

H-Pos / V-Pos / H-Size / V-Size /

Y-Level (1 ~ 20) / CR Level (1 ~ 20)

CB Level (1 ~ 20) / Return

IMAGE

The Image menu covers a variety of options including colour, sharpness, mirror, defog, shading and

privacy masking facilities.

Sharpness 1~ 10 (Default)

The sharpness control is done by digital correction and the best way to set this option is to set level

to maximum of 10, then flick back to 1, to see the difference. Then adjust to display sharpest picture

without displaying too heavy black lines around subjects.

Gamma 0.55 / 0.6 / 0.65 /0.45 / 0.5 (Default 0.55)

Gamma correction controls and adjusts the overall brightness of an image. Try the various options

to give best quality brightness.

Color Gain 1 ~ 20 (Default 12)

This option changes the colour gain. Try to match the colours displayed as close as possible on the

monitor with the colours viewed by eye.

Mirror Off / On

This option changes a left handed view to a right handed view if switched on.

Flip Off / On

This option turns a view upside down. This option is generally used with the Mirror function.

D-Zoom 1.0X ~ 8.0X (Default 1.0X)

The digital zoom function allows you to enlarge the view by expanding the pixel size. You will

notice that as picture size increases the sharpness of the picture deteriorates so you will only be able

to use the function up to a certain point of magnitude.

ACE Off / Low / Middle / High

Adaptive Colour & Contrast Enhancement (ACE) is an automated option for adjusting colour and

contrast as light levels changes through the day. Low, middle or high options are available.

HD-TVI XSEE515

SEE515 fixed lens Internal* HD-TVI & Analogue Camera with IR

Email: suppo[email protected] Last Revised 15/06/2017

DEFOG Off / On

Mode –Auto - Level - Low / Middle / High

Manual - Level - Low / Middle / High

The defog option can be used to improve the captured image in poor weather conditions such as

smog, fog or smoke. Three levels of optimisation can be applied, low, middle or high. This option

is useful to stabilise rapid fluctuating light levels.

SHADING Off / On

Weight 1% ~ 100% (Default 100%)

The shading option is used to provide overall shading with 100% providing no shading and 0%

providing full shading.

PRIVACY Off / On

Zone Num (0 ~ 15) This function allows the creation of up to 15 coloured

areas to be created to provide privacy masking.

Zone Disp Off /On The Zone Display allows you to switch on and off the

zone number.

H-Pos / V-Pos / H-Size / V-Size

Each area can be positioned using the H-Pos (horizontal position), VPos (vertical position) and

sized using the H-Size (horizontal size) and V-Size (vertical size) options. The Zone Display allows

you to switch on and off the zone number.

Y-Level (1 ~ 20)

CR Level (1 ~ 20)

CB Level (1 ~ 20)

The Y-Level is the colour hue for privacy masking and the CR Level (Chrominance Red) and CB

Level (Chrominance Blue) are used to create the required colour.

The pictures below show an area that has been masked, before and after.

RETURN

Return to main menu

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TVision Caméra de sécurité

TVision

TVision SEE250L Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur